No preview available
HomeMy WebLinkAbout260000-00070 Traffic Signal - Signal Gear - FOR REVIEW --TENW 4-7-17Submittal Submitted By NOTES: NOTES: NOTES: tryan 4/6/2017260000-0007 For Review 04/06/2017 The only cameras in this package are 4 Iteris Cameras, but there needs to be 2 Iteris Cameras and 2 Vector Video Cameras. 13301 S.E. 26th St. Bellevue, WA 98005 • (425) 747-5200 • www.primeelectric.com GROUP HEALTH LONGACRES SIGNAL Electrical Submittal 003 • Signal Gear April 5, 2017 1122 Industry Street, Bldg B Phone (425) 438-1133 Everett, WA 98203 Fax (425) 438-1585 1 March 31, 2017 Prime Electric, Inc. 13301 SE 26th St Bellevue, WA 98005 Attention: Andrew Hollenback Regarding: City of Renton GHC Longacres Materials List –SUBMITTALS Bid Item #1; Traffic Signal System - SW 27th Street @ Naches Avenue SW P PLUS CABINET: ITEM QTY DESCRIPTION 1 1 Type P+ controller cabinet per City of Renton specifications and including: (1) Type TS2-1 P+ aluminum enclosure three door (unfinished inside and outside) with two 19” equipment rack, Best Green CX core locks, terminal facilities including; loadbay, auxiliary panel, detector panel, fan & thermostat assembly and power supply interface panel. Western Systems Part # 2510510001, 3012500000 To include the following: (1) Controller EPAC M62; ATC / ATC COMM HUB / LINUX CPU / SEPAC 3.55A (1) (1) (1) (4) (16) (1) (6) (1) (1) (1) (1) Siemens ITS Part # M62 ATC/SEPAC3.55D Sub-Assembly Data Key 2MB 5V Flash (2070/Nema) Data Key Part # DATA KEY 2M / 611-0105-000A Smart Monitor (MMU2-16LE) 16 Channel Enhanced MMU w/FYA Support EDI Part # MMU2-16LE Power Supply (PS250) Shelf Mount (TS2) EDI Part # PS250 BUS Interface Unit TS2 EDI Part # BIU700 Load Switch 200 Reno A&E PDC Part # SSS-87I/O Flasher (SSF88) Discrete Caltrans (PDC) PDC Part # SSF-87 Flasher Transfer Relay (430) Detrol Detrol Part # 295 UPS Power Module 1100W w/ (6) Relays & 120V input/output IP/SNMP Alpha Part # 017-230-23 Automatic Transfer Switch Assembly with surge & RPA 120V Alpha Part # 020-168-25 Battery Heater Mat (3 Batteries) 13.5x8 1-Mast/2-Slave (P+) Alpha Part # 189-208-10 Battery Heater Mat (1 Batteries) 13.5x8 1-Mast/2-Slave (P+) Alpha Part # 189-209-10 1122 Industry Street, Bldg B Phone (425) 438-1133 Everett, WA 98203 Fax (425) 438-1585 2 ITEM QTY DESCRIPTION (2) Battery Equalizer for 1 string of 48v batteries Alpha Part # 012-306-21 (2) Battery Cable Harness Kit Alpha Part # 740-678-22 (8) Battery Alphacell 100XTV (56AH/39LB) 5Y Warranty Alpha Part # 1810226 (1) Patch Cable Cat 6 20FT (yellow) Evans Part # EVNSL624-0020 (2) Video Processor Iteris 2 Camera 24VCD Iteris Part # VEC-EDGE2-2N-PAK (1) Edgeconnect (MPEG4) Package (1) Module (4) ECM (1) RJ45 Mouse & Cables Iteris Part# EDGECONECT-PAK (1) Vantage Live Hosted Data Service / 3 Year Service Iteris Part # VLIVE-10-3YR (1) Monitor Color LCD 10.4” Defender Part # MON-10LCD (1) Opticom 764 Phase Selector 4CH GTT Part # 764 (1) Opticom 768 Auxiliary Interface Panel GTT Part # 768 (1) Cabinet / Shelf mounted central control unit iNavigator 2-wire system; Custom cable harness 50-pin connector used with ICCU-S (12’); Interconnect board for ICCU-S; SDLC Cable Polara Eng. Part # ICCU-S, 850-216, iN2-ICB, iN2-SDLC-CABLE (1) Power Cable 18AWG No Lugs 6FT Ruggedcom Part # 99-43-10-0008-001 (1) Ethernet Switch (6) 10/100TX ports & (2) 100Base SFP/GBIC Open Ports (Din Rail) w/ power cable Ruggedcom Part # RS940G-HI-D-2SFP (2) Mini GBIC/SFP Transceiver SM/LC 1310NM, 10KM Distance Ruggedcom Part # 25-101-0100 (1) Fiber wall mount (12 port) with (1) coupler plate 6 pack SM (SC) Simplex and (1) patch cord plates Bejed Part # BJ-2113B-002, BJ-6662S-106, BJ-6600U-100 Enclosed are (1) copy of submittal data sheets for the equipment on the above referenced project. Please return to Western Systems (1) submittal package with comments once approval has been granted. Any additional equipment required that changes the scope of the project will be addressed as a change order. Your order is currently not scheduled for a beginning delivery pending return of approved submittals. If a specific date is appropriate please confirm by written communication and we will do our best to meet your requirements. Sincerely, WESTERN SYSTEMS Shawna Storms Estimator 2017W1570 / WSQ WA-SS509A More Integration. More Power. Western Systems, the leader in innovative solutions for the transportation industry, introduces a new signal cabinet with an Integrated Battery Backup System (BBS). The patent pending P-Plus is the best All-In-One control cabinet with a BBS. UNIQUE FEATURES:  Combines a Traffic Signal Control and the Battery Back- up System, into one standard NEMA cabinet. Available in NEMA TS1 and TS2 Accommodates up to 16 position Load-Bay Provides up to 64 channels of detection Includes BBS generator bypass and batteries  Cabinet sizes: Type M36, P, Stretched-P, and R  Front door generator by-pass compartment Close, Lock & Secure it - while under generator power  Isolated battery compartment with side door access UNIQUE ADVANTAGES & BENEFITS:  Accommodates existing infrastructure Eliminates the need for an additional BBS cabinets  Savings on foundation construction Utilizes existing P cabinet foundations  Adding a Traffic Cabinet and BBS just got easier Requires no additional space to add BBS to congested street corners 1122 Industry St. Bldg. B | Everett, WA 98203 | P: 425.438.1133 | F:425.438.1585 www.WesternSystems-Inc.com P-Plus Patent No.13/624747 P-Plus More Power. More Integration. Standard Enclosure Specification 1. Completely fabricated from .125” - thick type 5052 +32 mill finished aluminum utilizing con- tinuously welded construction for maximum protection from contaminants. 2. Internal attaching components include twelve (12) ‘C’ mounting channels, (4) per side Wall and (2) on rear wall for attaching equipment panels. 3. The door opening is completely double-flanged to prevent water drops. 4. Thermoconvection air ventilation system utilized with provisions for mounting fan for forced-air cooling. 5. Exhaust outlet opening are provided under the roof-overhang. 5. Louvered inlet with filter to prevent dirt from entering with air flow. 7. All external & internal hardware is fabricated from stainless steel. 8. Continuous hinge is fabricated from stainless steel. 9. 3/4” diameter stainless steel inward turning han- dle with provisions for padlocking. 10. Automatic door stop to hold main door open at 90, 120, & 135 degrees. 11. Provided with Best Locks with a blue construc- tion core. 12. Enclosure is UL listed. 13. Powdercoated finishes, interior white & exterior gray 1122 Industry St. Bldg. B | Everett, WA 98203 | P: 425.438.1133 | F:425.438.1585 www.WesternSystems-Inc.com Patent No.13/624747 usa.siemens.com/mobility Description The Siemens m60 series ATC complies with the industry’s latest Advanced Traffic Controller (ATC) standard 5.2b. Built on the proven m50 hardware architecture, combined with powerful industry-leading SEPAC software, the Linux-based m60 series ATC provides a host of functions to meet the needs of traffic agencies of all sizes. The m60 series ATC provides multiple Ethernet, USB and other industry-specific interfaces, facilitating both backwards and forwards compatibility. The m60 series ATC also enables easy hosting of third-party applications. In addition, the m60 series ATC exceeds industry standards by providing usability features that include the new Siemens Multiview Display concept (SMD) with real-time active status, context-sensitive HELP screens and user-programmable favorite buttons. The m60 series ATC is truly a nerve center for the connected intersection of the future. usa.siemens.com/mobility m60 Series ATC An Advanced Traffic Controller for NEMA-style cabinets Features • ATC standard 5.2b compliant • 5 1/8-inch active TFT backlit LCD display with Siemens Multiview Display technology – Easily removable display and keypad – Easily identifiable discrete HELP button – Real-time context sensitive HELP screens – User programmable function buttons • Modular Communications hub – ENET1 and ENET2 network switches – 4 10/100 TCP/IP ports – 4 USB 2.0 ports – Datakey – SP8 port for GPS • Convenient field upgrade packages – Linux upgrade package – m50 USB package – m60 ATC upgrade package Benefits The Siemens m60 series ATC provides a vast array of benefits compared with other similar products in the industry. At the heart of the m60 series ATC is the Siemens Multiview Display (SMD) concept. The SMD provides the user with multiple time-saving mechanisms to operate and program traffic controllers. For ease of operation, the 16 line display is split into an active programming view at the top and a dynamically updated active status view – or the context- sensitive HELP – at the bottom. This dual view enables users to dynamically visualize the impact of their programming changes on the overall efficiency of the intersection. M62 ATC/Sepac 3.55D usa.siemens.com/mobility Subject to change without prior notice Printed in USA Order No.: RCM-DS-0025 © 2014 Siemens Industry, Inc. Siemens Industry, Inc. 8004 Cameron Road Austin, Texas 78754 1.512.837.8300 The information provided in this flyer contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract. All product designations may be trademarks or product names of Siemens AG or supplier companies whose use by third parties for their own purposes could violate the rights of the owners. In addition, the ability to program customized function buttons to a specific menu item ensures quick navigation, making the operation of an m60 series ATC fast and efficient. Having built upon the proven Siemens m50 hardware platform, the m60 series ATC offers a range of possibilities to address financial and technological constraints faced by traffic agencies. Controllers by Siemens Central Processor Unit (CPU) • Open architecture platform with standard Linux operating system • MPC 8270 266MHz processor • 512MB FLASH, 64MB DRAM and 1MB SRAM • TOD Clock with automatic daylight savings time adjustment • Power supply will power the SRAM during power failures Keyboard and Display • Siemens Multiview Display with duel view screens • Removable light-emitting diode backlit LCD Display with 16 lines of 40 characters with adjustable contrast setting • Emulation of terminal per Joint NEMA/AASHTO/ITE Standard • Key quantity and function per Joint NEMA/AASHTO/ITE Standard Communications Module • 10 Base-T Ethernet with built-in switch and 5 front panel RJ-45 connectors • 4 USB 2.0 Ports and a Datakey Port • Dedicated GPS Port • Unique MAC address assigned by the Institute of Elec-trical and Electronic Engineers (IEEE) • EIA-232 port for uploading/downloading applications software and OS updating • Single and multi-mode fiber optic options • 1200 bps Frequency Shift Keying (FSK) modem (optional) Controller Housing • 7 expansion slots with card guides for standard size Versa Modules and 2 slots with card guides for standard Joint NEMA/AASHTO.ITE ATC modems (optional) • Polycarbonate construction (excluding back panel), rear mounting tabs and aluminum power supply mounting plate for electrical grounding • Carrying handle All Siemens controllers and accessories are built with the highest standards in quality and manufacturing. With a long standing history of technological innovations, well renowned customer service, and high quality products and services, Siemens is the leader in traffic technology products and solutions. For more information on our product line see our website at www.usa.siemens.com/mobility. www.itssiemens.com SEPAC® Local Controller Software Effective traffic control software Giving high priority to public transportation without interrupting the general traffic flow has been a major challenge for conventional traffic control software in the past. Siemens’ SEPAC® local controller software is focused on enhancing performance of traffic signal control for customers who use Light Rail Transit, Bus Rapid Transit and regular Traffic Signal Priority functionality. Its features improve the use of low and full priority, with minimal impact on pedestrian and vehicle traffic. SEPAC is unparalleled traffic signal priority software that enables mobility, safety and a better environment in order to improve the quality of life in cities. The software is designed for Siemens “M” series and CalTrans 2070 style controllers. Incorporating more than 25 years of actual “on-street” traffic control experience, SEPAC is user-friendly and accommodates a large variety of traffic control requirements through its diverse configuration capabilities. Programming advantages ƒUser-friendly, 8 line menu driven software ƒEach parameter viewable with a menu and the cursor movable to that parameter for changes ƒEasy verification with related parameters visible simultaneously ƒOn-screen programming area identification and editing prompts ƒStandard traffic nomenclature used throughout the programming ƒKeystrokes identical on any hardware platform ƒLogically laid out programming for easy setup and startup Modes of operation SEPAC’s traffic capabilities include five modes of operation that allow for Time of Day (TOD) operations, week plans, time of year or holiday plans, which include: coordination, free and flash functions. Modes include: ƒStandalone – All functionality is operational as a standalone unit. Time updates available through GPS syncs. Controller can be programmed to use the GPS output for keeping its internal TOD clock accurate. ƒMaster Control – In conjunction with a Marc Master Controller, SEPAC will work within a closed loop system.** ƒSystem Control – SEPAC has the ability to communicate to TACTICS® and operate under system control. ƒManual – SEPAC can be controlled manually to run specific coordination routines when set to manual, including free operation. ƒAdaptive Control – SEPAC can accept commands from SCOOT® and ACS Lite for adaptive control, if available. Siemens M50 controller running SEPAC® local controller software Siemens Industry, Inc. 8004 Cameron Road Austin, Texas 78754 Tel: +1.512.837.8300 Fax: +1.512.837.0196 © 08.2012, Siemens. All rights reserved. Trademarks used are property of Siemens or their respective owners. Siemens is your partner to develop an intelligent and economical transportation solution that will increase the quality of life in your city by improving safety, energy efficiency and traffic-flow, while generating capital that can be invested in additional infrastructure upgrades. With the most comprehensive portfolio of integrated transportation products, services and solutions, Siemens keeps America moving. Siemens reserves the right to alter any of the Company’s products or published technical data relating thereto at any time without notices. www.itssiemens.com Siemens SEPAC® Local Controller Software Features Phases • 16 vehicle phases • 8 pedestrian phases • 4 phase banks • 4 timing rings • 15 alternate sequences • 16 overlaps Coordination • 6 modes of coordination • Locally based traffic responsive routines • 250 events • 5 modes for transition • 3 auxiliary and 8 special functions • 99 day and 10 week programs • Free / flash / dimming • 16 phase function maps Detection/Inputs • 64 vehicle detectors* • 8 pedestrian detectors* • 8 system detectors* • Ethernet detection interface for Sensys Ethernet Access Points (optional) Communications • Supports Siemens SCOOT® communication via Ethernet • IP / Serial / FSK communications to TACTICS® • IP standard on “M” series and 2070 1-B, 1-C and 1-E cards (2009 TEES) Priority and Preemption • 6 preempts • 6 LRT / TSP (high / low) priority routines • 4 priority banks with unique timing • Allows for 24 specific actions • 6 detectors per approach • 19 vehicles tracked simultaneously • Up to six directions at one time • Tracks vehicles at any distance from intersection using up to 6 inbound detectors and one exit detector • Tested and verified with: Opticom® by GTT, EMTRAC®, E-Views® and Wayside Detection • Allows for seamless operation between transit and vehicle traffic • Adjusts splits, skips phases when necessary, and adjusts lead/lag in order to make the transitions between normal operation and priority service more fluid • Low and high priority can be used for both bus and light rail vehicles Miscellaneous • Collision avoidance routines (Red Protect) • Available when used with a speed detector such as Iteris’ new Vantage Vector™ video and radar camera • Bike timing with specific times for large bike traffic areas • Any detector can be used for bike detection • Advanced and delayed WALK operation • Advance Warning Flasher functions • SPaT output for Connected Vehicle® operations • Logging and diagnostics, including: cycling, coordination, preemption, detection, outputs, alarms and communications • Anti-Backup (yellow trap avoidance) • Password protection • Unit to Unit transfer • External back-up - USB or DataKey® • Help screen • Illinois Rail Road security available • International timing • Extensive reporting capabilities Hardware Platforms • OS-9 or Linux Operating System • NEMA or CalTrans specifications • Meets all current NTCIP requirements for traffic signal control • Cabinet types include: TS-1, TS-2, TS-2 Type 2, CalTrans 332 style, ITS and CBD • External Memory Storage • OS-9 uses DataKey® • Linux uses USB memory sticks or DataKey® * 80 total detectors defaulted to listed configuration but can be programmed as different types, if necessary. ** SEPAC has been developed to be used in combination with SEMARC (Master Controller Software) in the same controller, eliminating the need for two controllers in one cabinet. MMU2-16LE Catalog Sheet – 120312 Designed, Manufactured and Tested in the United States of America ISO 9001:2008 Registered SmartMonitor and LEDguard are registered trademarks of Eberle Design Inc. U.S. Pat. No. 7,246,037 Complies With The New NEMA MMU2 Standard and MUTCD Requirements MMU2-16LE SERIES NEMA LCD MALFUNCTION MANAGEMENT UNIT  MMU2-16LEip with Ethernet Port  MMU2-16LE with EIA-232 Port Whether you’re a NOVICE or EXPERT  Use a built-in SETUP WIZARD to quickly and accurately configure the Signal Monitor to the exact requirements of the cabinet and intersection? Signal Technician, wouldn’t it be great if you could:  Use a MENU DRIVEN LCD interface to view vital cabinet operational details such as field signal voltages, historical event logs, and monitor configuration data?  Use a built-in DIAGNOSTIC WIZARD to automatically diagnose cabinet malfunctions and pinpoint faulty signals? If your answer is Yes, the MMU2-16LE SmartMonitor® is for YOU! NEW MMU2-16LE SmartMonitor® ENHANCED FEATURES NEMA TS2-2003 (R2008) Standard Including Amendment #4: The MMU2-16LE SmartMonitor® meets all specifications of the NEMA Standard TS2-2003 (R2008) for the MMU2 configuration while maintaining compatibility with NEMA TS1-1989 Assemblies. NEMA Standard Flashing Yellow Arrow PPLT: The MMU2-16LE SmartMonitor® supports MUTCD Flashing Yellow Arrow PPLT operation and meets / exceeds the NEMA Standard MMU2 requirements of TS-2 Amendment #4-2012, providing modes for both TS-2 or TS-1 cabinet configurations. Standardized Communications: Real-time SDLC communications with the Controller Unit exchanges field input status, Controller Unit output status, fault status, MMU programming, and time and date. Full Intersection & Status Display: Two high contrast, large area Liquid Crystal Displays (LCD) continuously show full RYG(W) intersection status. A separate graphic LCD provides a menu driven user interface to status, signal voltages, configuration, event logs, and the Help system. Event Logging: A time-stamped nonvolatile event log records the complete intersection status as well as AC Line events, configuration changes, monitor resets, temperature and true RMS voltages. Setup Wizard: Use the built-in Setup Wizard to configure the Nema Enhanced settings of the SmartMonitor® by answering a short series of questions regarding intersection design and operation. Diagnostic Wizard: and Help System The Diagnostic Wizard automatically pinpoints faulty signals and offers trouble-shooting guidance. The integrated Help System provides context sensitive operational assistance. TS-1 Type 12 with SDLC Mode: The MMU2-16LE SmartMonitor® can be configured to operate with the Port 1 SDLC function and Diagnostic Wizard enabled in a TS-1 twelve channel cabinet with no cabinet wiring changes. Program Card Memory: Enhanced settings of the MMU2-16LE SmartMonitor® are stored in nonvolatile memory on the EDI Program Card. Moving the Program Card to another MMU2-16LE automatically transfers all settings. Signal Sequence History Log: The five Signal Sequence History logs stored in nonvolatile memory graphically display up to 30 seconds of signal status prior to each fault event. LEDguard®: This EDI innovative signal threshold technique can be used to increase the level of monitoring protection when using LED based signal heads. EDI RMS-Engine: A DSP coprocessor converts AC input measurements to True RMS voltages, virtually eliminating false sensing due to changes in frequency, phase, or sine wave distortion. ECcom PC Software: Access to the MMU2-16LE data is provided by the industry standard EDI ECcom Windows based software for status, event log retrieval, configuration, and data archival. PS-250 Catalog Sheet – 052206 Designed, Manufactured and Tested in the United States of America ISO 9001:2000 Registered HHHeeeaaavvvyyy DDDuuutttyyy CCCaaabbbiiinnneeettt PPPooowwweeerrr SSSuuupppppplllyyy The ideal power source when using high current devices such as video detection cards. The PS-250 Cabinet Power Supply is a shelf mounted unit which supplies regulated DC power, unregulated AC power, and a line frequency reference for the Detector Rack, BIUs, load switches, and other auxiliary equipment. The PS-250 meets and/or exceeds all requirements of the NEMA TS2-2003 Standard. All TS-2 Type 1 cabinet assemblies require the use of this unit as well as any TS-2 Type 2 cabinet assemblies that utilize Bus Interface Units (BIU). Each EDI PS-250 Cabinet Power Supply is put through a rigorous three part Total Quality Assurance program and tested under the extreme environmental conditions experienced on the street. It is this commitment to quality and performance that EDI products are known for, providing years of trouble free operation. PS-250 OPERATIONAL FEATURES Basic Functions: The PS-250 provides four outputs rated over the full -30oF to 165oF (-34oC to +74oC) Nema operating temperature range: ; +12 VDC rated at 5 Amps ; +24 VDC rated at 2 Amps ; 12 VAC rated at 0.25 Amps ; 60 Hz Line Frequency Reference rated at 50 mAmps ; Input Voltage Operating Range is 89 Vac to 135 Vac at 50 Hz Display Indicators: A separate LED indicator is provided to display output status and fuse integrity for the three supply outputs. The Line Frequency Reference LED indicator pulses to show 60 Hz activity. Input / Output Pins: Pin Function A AC Neutral B Line Frequency Reference Output C AC Line Input D +12 VDC Output E +24 VDC Output F Reserved G Logic Ground H Earth Ground I 12 VAC Output J Reserved Test Points: Individual test jacks are provided for the +12 VDC output, +24 VDC output, and Logic Ground reference. Output Protection: The +12 VDC, +24VDC, and 12 VAC outputs are fused for over-current protection. Each output is protected against voltage transients by a 1500 Watt suppressor. Dimensions: 8.2 inches High x 4 inches Wide x 8 inches Deep BIU-700 Catalog Sheet – 011712 Designed, Manufactured and Tested in the United States of America ISO 9001:2008 Registered NEMA TS-2 BUS INTERFACE UNIT The BIU-700 Bus Interface Unit (BIU) performs the interface between Port 1 of the Controller Unit and the Loop Detector Racks, Terminals and Facilities, and other devices in a NEMA TS-2 Cabinet Assembly. Its functions include controlling load switch outputs, detector resets, communicating with Inductive Loop Detectors and other devices, and the conditioning and conversion of Terminals and Facilities and Loop Detector call inputs for the Controller Unit. The EDI BIU-700 is compatible with all Controller Units and Cabinets compliant with the requirements of NEMA Standard TS2-2003. Each EDI BIU-700 is put through a vigorous three part Total Quality Assurance program and tested under the extreme environmental conditions experienced on the street. It is this commitment to quality and performance that EDI products are known for, providing years of trouble free operation. Model Options: BIU-700 Standard product (BIU Configuration) BIU-700H Half Width product (BIU Configuration) BIU-700 OPERATIONAL FEATURES Basic Functions: The BIU-700 Bus Interface Unit meets or exceeds all requirements of the NEMA Standard TS2-2003 for the BIU configuration. Display Indicators: Separate Power, Receive, and Transmit LED indicators display DC power status and SDLC Port 1 status. Input / Output Pins: Signal I/O Configuration:  15 DC Output pins  24 Programmable Input / Output pins  8 DC Input pins  4 Optically isolated input pins  1 Line Frequency Reference input pin  4 Address Select input pins Output Drivers: All outputs are rated at 150mA continuous sink current. Each output provides a 500mA typical current limit. Outputs are rated to 50 volts and utilize a voltage clamp for inductive transient protection. Isolated Inputs: Four optically isolated inputs provide isolation for Pedestrian Detector and Remote Interconnect inputs. These inputs are intended for direct connection to 12 Vac from the cabinet power supply for Pedestrian Detector applications. They may also be connected for 'Low True' DC applications when the Opto Common pin is connected to a 24Vdc supply. NEMA BIU2 Support The BIU-720, BIU-730, and BIU-740 models can be configured to meet the BIU2 configuration as defined by TS2-2003, clause 8.3. These models provide detector rack communication capabilities plus an optional front panel EIA-232 or Ethernet communication port. Consult the factory for details. unun DATA SHEET SSS-87IO Solid State Loadswiteh: Description: The PDC SSS-871/O Loadswiteh series isa tri-pack.modular,solidstaterelaydesignedspecificallyto meetNEMA specillcations.as wellas Californiaand NewYork"Model200''specifications.Each loadswiteh contains3 individually replaceable modules that are enclosed in a dust resistant, metal enclosure providing mechanical protection and excellent heat sinking for the modules. The modules are easily accessible with the use of a screwdriver. Each loadswiteh also features a L.E.D. indicator on each output circuit. Installation: Theswitchpae intermates with anystandard NEMA loadbay or with the model 332cabinet outputfileas well as with any NEMA loadbay.Itiseasily installedor removed bygraspingthe handle.ConnectorPI pinoutsarc shown in FIG I. The connector mates with a PDC BCS-12 or equal. PIN FUNCTION 1 +1I5VAC.60 11/. 2 Chassis Ground 3 A Output (Red.Don't Walk) 4 Not Assigned 5 B Output (Yellow) 6 A Input (Red,Don't Walk) 7 C Output (Green, Walk) 8 B Input (Yellow) 9 +24 VDC 10 C Input (Green.Walk) 11 AC- 12 Not Assigned General Characteristics: PI (PI as viewed from the outside of the product looking directly at the connector) FIG I. |2 1| | 4 3| 5| I8 7| |10 |l2 " 9| 11 1 Model SSS-871/0 Series Uses Module it SSR-87 Meets Specs for Nema.Caltrans.NY (model 200) Load voltage 120 VAC current (max)15.0 Amps (Tungsten Filament Load) Control Signal voltage +24VDC current 20.0 MA (max) Switching 1stalternation after +10Degrees of linevoltageat thezero signalisapplied.crossoverpoint. Succeedingalterations +5 Degrees of linevoltageat the zero crossover point. dv/dt 100 V per microsecond line to load resistance 15 K Ohms Min leakage current less than 20 MA voltage 2500 VDC Min resistance 10Meg Ohms Min one cycle 175Amps RMS Min one second 40 Amps RMS Min operations 30 million Min length 8.40 inches width 1.74 inches height 4.185 inches weight 1.135 LBS Guarantee:The SSS-871/0 series is fully guaranteed against all failures duetomanufacturing defects for two years. P.O. Box 7172 #205 Stateline. NV. 89449 • PII(916)786-2957 • FAX (916)786-2950 Off State Isolation Surge Current Life Mechanical Specifications subject to change without notice 295 POWER RELAY 295 Applications Rev 10/16/06 Page 1 of 2 Power relay rated for 20 amps Tungsten (2.4 KW @ 120/240 VAC) switching on all contacts in a DPDT configuration. • Traffic controller equipment Features • 20 amp Tungsten switching on all contacts • Molded class F (155º C) coil construction • Contacts designed for superior switching performance • Contact wiping action results in long contact life • PPS molded panel for superior physical characteristics Contact Data Expected Life   • Configuration: DPDT   • Electrical: 200,000 operations min. @ rated load • Material: Silver Cadmium Oxide   • Mechanical: 5,000,000 operations min. @ no load • Size: 3/8” diameter Dielectric Strength Contact Ratings   • Across open contacts: 1200 VRMS • Tungsten load rating   • Contacts to coil: 2200 VRMS • 20 Amps @ 120 VAC (2.4 KW)  • Contacts to frame: 2200 VRMS • 10 Amps @ 240 VAC (2.4 KW)  • Pole to pole: 2200 VRMS Coil Data Mechanical Data   • Nominal input voltage: 120/110 VAC, 60/50 Hz   • Operating position: Any   • Nominal coil power: 7.0 VA   • Mounting: Cinch-Jones 2408 8 pin socket or equiv.   • Coil resistance: 970 Ohms ±10%  • Terminals: 0.250” x 0.055” (6.35mm x 1.40 mm)   • Coil insulation: Molded Rynite® class F system   • Insulation material: Thermoplastic 94V-O rating   • Insulation resistance: 100 Megohms minimum   • Cover material: Clear Polycarbonate 94V-2 rating   • UL insulation system file No: E74443   • Cover protection category: 40 IP rating Operate Data   • Weight: 7.0 oz. (198 grams) approx. • Pull-in voltage: ≤ 75% of nominal voltage Agency Information • Drop-out voltage: ≥ 30% of nominal voltage   • UL recognized file No.: E37066 (US & Canada) • Operate time: 20 ms approx.  • NEMA: Exceeds NEMA Standard TS 2-2003 • Release time: 20 ms approx.  • D.O.T. Approvals: Temperature Data • Operating ambient: -40ºC to +65ºC • Storage ambient: -40ºC to +130ºC Rynite® is a registered trademark of EI du Pont de Nemours and Company Specifications subject to change without notice 295 Rev 10/16/06 Page 2 of 2 Outline Dimensions (Dimensions shown in inches and [millimeters] Wiring Diagram (Viewed from pin end] Your Power Solutions Partner > 1100W/VA UPS module designed to operate in extreme environments and provide maximum flexibility while ensuring critical loads remain protected and running during power outages and other power disturbances > Wide range Automatic Voltage Regulation (AVR) lengthens battery life by providing protection without transferring to backup mode during voltage surge or sag > Independently programmable control and report dry contacts allow monitoring and controlling of key functions > Temperature compensated battery charging protects batteries from overcharging or undercharging at extreme temperatures, extending the life of the battery > Local and remote monitoring and control via RS232 port and Ethernet SNMP interface* > UPS panels can be rotated, improving usability and viewing convenience FXM 1100 Rugged UPS Module FXM 1100 Alpha FXM is a line of rugged UPS power modules used worldwide in the most demanding environments where clean backup power is needed. Designed to perform in the most extreme demanding environments, Alpha FXM units ensure equipment in security, communications, traffic, industrial environments, and many other critical applications remains safe and protected from power disturbances. Thanks to its powerful programmable battery charger, the FXM is capable of providing the runtime you need. All FXM models are available in 120Vac and 230Vac. *Ethernet SNMP card is standard on the 120Vac model and optional on the 230Vac model Part # 017-230-23 Alpha Technologies Ltd. For more information visit www.alpha.ca member of The Group™ Canada: Burnaby, British Columbia Tel: 604 436 5900 Fax: 604 436 1233 United States: Bellingham, Washington Tel: 360 647 2360 Fax: 360 671 4936 Alpha Technologies reserves the right to make changes to the products and information contained in this document without notice. Copyright © 2013 Alpha Technologies. All Rights Reserved. Alpha® is a registered trademark of Alpha Technologies. member of The Alpha Group™ is a trademark of Alpha Technologies. #0480013-00 Rev D (01/2013) FXM 1100 Rugged UPS Module Consult your Alpha representative for P/N configurations Electrical >120Vac Model Battery string voltage: .......48Vdc Nominal voltage: ...............120Vac Frequency: ........................60/50Hz ±5% (auto-detection) Input: Voltage range: ................85 to 175Vac Current: ...........................9.8A nominal Output: Waveform:.......................Pure sinewave Nominal voltage: ............120Vac Voltage regulation: .........+/- 10% over input voltage range Power at 50°C:................1100W/VA Frequency: .....................Output frequency = Input frequency >230Vac Model Battery string voltage: .......48Vdc Nominal voltage: ...............230Vac Frequency: ........................60/50Hz ±5% (auto-detection) Input: Current: ...........................5.1A nominal Voltage range: ................150 to 328Vac Output: Waveform:.......................Pure sinewave Nominal voltage: ............230Vac Voltage regulation ..........+/- 10% over input voltage range Power: .............................1100W/VA Mechanical Dimensions: mm: .................................133H x 394W x 222D inches: ............................5.22H x 15.5W x 8.75D Weight: ..............................16kg (35lbs) Environmental Operating temp range*: .....-40 to 74°C (-40 to 165°F) Audible noise @ 25°C: ......45dBa @ 1 meter (39in) *Derates after 55°C Performance Typical output voltage THD: ........<3% Typical efficiency: ......................>98% (resistive load) Typical transfer time: .................<5ms Power Connector Options Agency Compliance*** Electrical safety: ................UL1778, CSA 22.2 No 107.3-03 Marks: EMI: ...................................Class A FCC/CISPR [EN 50091-2:1995] *** Compliance only applies to units with standard input and output connectors. Contact us for compliance information on models with optional power connectors ****CE applies to 230Vac version only 120Vac Model Input Output Standard Terminal Block Terminal Block Optional Terminal Block Terminal Block + Dual 5-15R IEC**IEC** 230Vac Model Standard Terminal Block Terminal Block * *FXM models with IEC connectors come with 4 lines LCD display instead of the traditional 2 lines display **** Transfer and Bypass Switches ATS, MBP, GTS and ABP > Available in four dependable power transfer options > Cost-effective transfer and bypass solutions > Ensures continuous power to equipment > Eliminates operation downtime due to maintenance > Offers easily mountable wall, shelf or rack configurations Alpha Technologies’ Automatic Transfer Switch (ATS), Automatic Bypass Switch (ABS), Manual Bypass Switch (MBS) and Generator Transfer Switch (GTS) are ideal for the Novus UPS series, particularly for outdoor traffic applications. The Automatic Transfer Switch transfers the critical load to the UPS when the utility line fails or is out of tolerance range. The Automatic Bypass Switch acts as a fail-safe device by switching the critical load to the utility line if there is a fault on the UPS. The Manual Bypass Switch allows for a mechanical bypass of the UPS without affecting the power to the critical load. The Generator transfer Switch automatically transfers the input to the UPS from the utility line to a portable AC generator. ATS/ABS MBP GTS Part # 020-168-25 United States Bellingham, Washington Tel: 360 647 2360 Fax: 360 671 4936Canada Burnaby, British Columbia Tel: 604 430 1476 Fax: 604 430 8908 For more information visit www.alpha.com Alpha Technologies Alpha Technologies reserves the right to make changes to the products and information contained in this document without notice. Copyright © 2006 Alpha Technologies. All Rights Reserved. Alpha® is a registered trademark of Alpha Technologies. member of The Alpha Group™ is a trademark of Alpha Technologies. 049-239-10-002 (4/06) Nominal Specifications Model: Automatic Transfer Switch Generator Transfer Switch Maintenance Bypass Switch Automatic Bypass Switch Input/Output Typical Voltage: 120VAC 120VAC 120VAC 120VAC Voltage Range: 92 to 135VAC (120 nom) 93 to 135VAC (120 nom) 94 to 135VAC (120 nom) 95 to 135VAC (120 nom) Input Frequency: 50Hz or 60Hz ±5% 50Hz or 60Hz ±5% 50Hz or 60Hz ±5% 50Hz or 60Hz ±5% Current: 40A 20A 20A** 20A Performance Transfer Switch Type: Relay Relay Rotary Cam Type, Break Relay Before Make, rated at 20A Transfer Time: <150ms 30sec delay <150ms <150ms Environmental Operating Temperature: -37 to 74˚C -37 to 74˚C -37 to 74˚C -37 to 74˚C Storage Temperature: -40 to 74˚C -40 to 74˚C -40 to 74˚C -40 to 74˚C Humidity (non-condensing): <95% <95% <95% <95% Altitude* 10000ft/3000m 10000ft/3000m 10000ft/3000m 10000ft/3000m Mechanical Width (in/mm): 4.75/120.6 4.75/120.6 4.75/120.6 4.75/120.6 Depth (in/mm): 6.5/165 6.5/165 6.5/165 6.5/165 Height (in/mm): 4.6/117 4.6/117 4.6/117 4.6/117 Weight (lb/kg): 7/3.2 7/3.2 4/1.8 7/3.2 Mounting: Wall mount, 4 points/shelf mount Wall mount, 4 points/shelf mount Wall mount, 4 points/shelf mount Wall mount, 4 points/shelf mount Connection AC Input: Terminal Block Terminal Block Terminal Block Terminal Block AC Output: Terminal Block w/Aux 5-15R Terminal Block Terminal Block w/Aux 5-15R Terminal Block w/Aux 5-15R UPS Input/Output: 14/3, 2 meter line cord n/a Terminal Block 14/3, 2 meter line cord Compliance Packaging: Designed to meet ISTA program Designed to meet ISTA program Designed to meet ISTA program Designed to meet ISTA program Warranty: 24 months 24 months 24 months 24 months Electrical Safety: UL-1778, CSA 22.2 No. 107.1 UL-1778, CSA 22.2 No. 107.1 UL-1778, CSA 22.2 No. 107.1 UL-1778, CSA 22.2 No. 107.1 * De-rate operating temperature above 1500m (4900ft) by 2°C per 300m (1000ft) ** 40A rack mount MBP also available Transfer and Bypass Switches Automatic Bypass Switch Electrical Diagram Transfer Switch Electrical Diagram Your Power Solutions Partner > Durable polyester construction for long service life > Sealed on-mat electronics for maximum protection > On-mat thermal switch and thermal fuse for redundant safety > Insulated design directs heat to the batteries and not to the enclosure for a 30% reduction in battery heating costs > Piggyback plug standard on 120V models Battery Heater Mats Extend Battery Runtime in Cold Weather Alpha's battery heater mats are designed with safety and efficiency in mind. Alpha's battery heater mats are a low-cost way of keeping backup batteries operating at their optimal temperature, maintaining battery backup performance at >70% of nominal levels at ambient temperatures below 32°F/0°C. The heater mats' insulated bottom ensure that energy is directed to the batteries and not wasted heating the enclosure. Durable polyester outer shells protect the heating elements from damage; their redundant thermal control protection ensures against overheating; and their fused power input protects against shorts. Alpha battery heater mats are a smart addition to any backup power system. Battery Heater Mats Part # 189-208-10 & 189-209-10 Canada: Burnaby, British Columbia Tel: 604 436 5900 Fax: 604 436 1233 United States: Bellingham, Washington Tel: 360 647 2360 Fax: 360 671 4936 Alpha Technologies reserves the right to make changes to the products and information contained in this document without notice. Copyright © 2010 Alpha Technologies. All Rights Reserved. Alpha® is a registered trademark of Alpha Technologies. member of The Alpha Group™ is a trademark of Alpha Technologies. Alpha Technologies Ltd. For more information visit www.alpha.ca member of The Group™ #0470025-00 Rev A (10/2011) Battery Heater Mats Consult your Alpha representative for P/N configurations Line Cord Thermostat Turn on Temp:5 deg C Turn off Temp:15 deg C Mat Mounted Thermostat Over Temp Off:50 deg C Turn Back on:40 deg C Thermal Fuse Rating:85 deg C Optional Line Cord Thermostat Turn on Temp:0 deg C Turn off Temp:10 deg C . Typical Stand Alone Mat Typical Master/Slave Mat 1 2 3 4 51 2 3 3 4 4 5 5 6 Master Slave All Mats The main power connector (1) on the heater mat is plugged into an AC source. In low temperature conditions the main control thermistor (2) will allow power to flow to the heater mat coil (5). The thermistor is mounted on the power cord so that it reacts to the enclosure temperatures and not the mat surface temperature. A secondary thermistor (3) is mounted on the mat with significantly higher temperature settings than the main thermistor (2). This thermistor keeps the mat from overheating during extended run periods. A thermal fuse (4) is a final fail safe device. The power connector (1) has an AC receptacle so that additional mats can be plugged in. Its parallel wiring keeps the failure of the first mat from affecting the operation of others in the string. Note: Battery Heater Mats are one element in providing an optimal thermal environment for your batteries. Properly installed and used in conjunction with Alpha's robust batteries and outdoor enclosures, the battery heater mats will improve battery performance and effective service life. AlphaGuard™ Battery Charge Management System Extends battery life Replace single batteries, not the entire string Spreads charge voltage equally across batteries Compensates for battery differences as they age Optional status-monitoring communications-interface modules Safe unattended operation designed to CSA C22.2 No. 107.1 and UL 1778 Standards AlphaGuard monitors and protects your batteries by spreading the charge voltage equally across all the batteries in the string, ensuring that every battery, whether old or new, is properly charged. With an ideal voltage always across each battery, life and runtime are optimized. Individual batteries in a string can be replaced as they fail, allowing batteries to be left in service longer. This stops the wasteful and costly practice of replacing batteries based on a scheduled maintenance programs or disposing of batteries that may have years of useful life left because one battery has failed. Part # 012-306-21 United States Bellingham, Washington Tel: 360 647 2360 Fax: 360 671 4936Canada Burnaby, British Columbia Tel: 604 430 1476 Fax: 604 430 8908 For more information visit www.alpha.com Alpha Technologies Alpha Technologies reserves the right to make changes to the products and information contained in this document without notice. Copyright © 2006 Alpha Technologies. All Rights Reserved. Alpha® is a registered trademark of Alpha Technologies. The Alpha Group™ is a trademark of Alpha Technologies. 049-225-10-007 (11/06) AlphaGuard The AlphaGuard employs a patented Charge Management Technology (CMT) to shuttle excess charge current to batteries requiring a greater charge, and is contained in a small plastic enclosure that installs directly on top of one the batteries in the string. A short service cable connects the AlphaGuard to each of the batteries in the string. Both 36VDC (3 battery) and 48VDC (4 battery) versions are available. One AlphaGuard is required per string. An AlphaGuard confi gured with the optional voltage sense cabling and interface module (DSM, ESM, EDSM or External DOCSIS®) allows the AlphaGuard to interface with a status-monitoring module. Two AlphaGuard modules can be connected to an interface module. Refer to individual interface module documentation for additional information. Models AG-CMT-3: AlphaGuard Charge Management SC, 36V String—including 36VDC battery interface cable AG-CMT-4: AlphaGuard Charge Management SC, 48V String—including 48VDC battery interface cable Battery Ring Lug .40” .52” Battery Cable 36V 6ft Battery Cable48V 6ft AG-DSM-S9-Cable AG-DSM-D9-Cable AG-DSM-D35-Cable AG-DSM-S35-Cable AlphaGuard Enclosure Specifi cations Confi guration Quantity: One (1) AlphaGuard is required per battery stringService Location: With the battery string Cabling AG-S9-Cable: AG-CMT-36/48SC Voltage Sense Cable, Single String, 9’AG-D9-Cable: AG-CMT-36/48SC Voltage Sense Cable, Two String, 9’AG-S35-Cable: AG-CMT-36/48SC Voltage Sense Cable, Single String, 35’AG-D35-Cable: AG-CMT-36/48SC Voltage Sense Cable, Two String, 35’ Mechanical Housing Material: High impact plasticDimensions (in): 1.44H x 4.82W x 4.25D (mm): 36H x 122W x 108DWeight (lb): 0.8 (kg): .36 Electrical Batteries: Individual 12VDC nominal batteries confi gured into 36 or 48VDC stringsCircuit Protection: Single blow fuse, reverse polarity protectedEnvironmental: -40 to 55°C (-40 to 131°F), 5 to 95% humidityQuiescent Current Draw: 1mA max. (Current consumed by AlphaGuard after low voltage total shutdown)Charge Management: Most effective during fl oat period of chargeMax. Current: 2A @ 25°CQuality of Final Balance: ±100mV max. between any two (2) batteriesCharging Effi ciency: 80 to 90%Charge Balance:±100mV typical Low Voltage Cutoff: 34.5VDC/46VDC ±5% Communication to XM2: AlphaGuard confi gured DSM status monitoring cardVoltage Sense Regulation: ±100mV Warranty 5 years Your Power Solutions Partner > Extreme temperature Absorbed Glass Mat (AGM) technology > Better cold temperature performance for outdoor applications > Longer runtimes help increase network reliability > Multiple models provide options for all network architectures > Power density gains allow more runtime from smaller sized battery > Extended service life for non-temperature controlled outdoor enclosures > Full 5-year replacement warranty* AlphaCell™ XTV AGM Top-Terminal Batteries The AlphaCell XTV Battery line is specifically designed for extreme outdoor temperature applications. It's virgin lead-alloy grids minimize corrosion and maximize life expectancy. Patented Computerized Charge/Discharge System (CCDS) provides 100% out-of-box runtime capacity. Strategic global manufacturing and distribution locations available with non-spillable transportation ratings. Optimized for remote advanced status monitoring. *When used with Alpha approved power supplies and enclosures in USA and Canada. For other regions see manual for details Part # 1810226 Alpha Technologies Ltd. For more information visit www.alpha.ca member of The Group™ Canada: Burnaby, British Columbia Tel: 604 436 5900 Fax: 604 436 1233 United States: Bellingham, Washington Tel: 360 647 2360 Fax: 360 671 4936 Alpha Technologies reserves the right to make changes to the products and information contained in this document without notice. Copyright © 2014 Alpha Technologies. All Rights Reserved. Alpha® is a registered trademark of Alpha Technologies. member of The Alpha Group™ is a trademark of Alpha Technologies. #0470133-00 Rev B (10/2014) AlphaCell XTV Extreme Temperature Batteries Nominal Specifications Battery Models 100XTV 150XTV 195XTV 240XTV Operating Temperature Range (w/ Temperature Compensation)-40 to 60°C / -40 to 140°F (charger temperature compensation @ ±3.3mVpc per °C) Storage Temperature -10 to 40°C (14 to 104°F)-10 to 40°C (4 to 104°F)-10 to 40°C (14 to 104°F)-10 to 40°C (14 to 104°F) Self Discharge Battery can be stored up to 12 months at 25°C (77°F). Higher temperatures during storage will require more frequent recharge. Voltage Per Unit 12V 12V 12V 12V Float Charge Voltage 13.5 to 13.8VDC average per 12V unit at 25°C (77°F) Refresh/Boost Charging Voltage 14.4 to 15.0VDC average 12V unit at 25°C (77°F) Maximum AC Ripple (Charger)0.5% RMS or 1.5% of float recommended for best results. Maximum voltage allowed = 4% P/P Terminal Type Threaded alloy insert terminal to accept M6 x 12mm bolt Threaded alloy insert terminal to accept M6 x 20mm bolt Terminal Hardware Torque 13.6NM / 120in-lbs 13.6NM / 120in-lbs 13.6NM / 120in-lbs 13.6NM / 120in-lbs Case Sizes 22NF 24 27 31 Dimensions mm 207H x 228L x 138W 214H x 275L x 168W 214H x 322L x 169W 217H x 343L x 170W inches 8.17H x 9.01L x 5.46W 8.44H x 10.85L x 6.65W 8.43H x 12.71L x 6.67W 8.57H x 13.50L x 6.71W Weight Approximate 17.7kg (39lbs)25.4kg (56lbs)30.5kg (67lbs)32kg (75lbs) Runtime Rating 25A (@ 25°C/77°F to 1.75Vpc)100 minutes 150 minutes 195 minutes 240 minutes Amp Hour Capacity 20Hr Rate (@ 25°C/77°F to 1.75Vpc)56Ah 80Ah 100Ah 112Ah Maximum Discharge Current 300A 800A 800A 850A Short Circuit Current 1450A 1900A 2250A 2650A Impedance 60Hz (approximate)0.005Ω0.0045Ω0.0039Ω0.0034Ω Conductance Range Fully Charged New Battery (@ 25°C/77°F) 700 - 800 900 - 1100 1050 - 1250 1250 - 1550 Terminal hardware included with every battery Constant Current Nominal Ratings in Amps (@ 25°C / 77°F to 1.75V per Cell) Discharge Time (Hours)1 2 3 4 5 6 8 10 12 20 100XTV 39.4 22.1 15.8 12.4 10.3 8.7 6.7 5.4 4.6 2.8 150XTV 53.0 30.6 21.6 16.8 13.9 11.9 9.3 7.7 6.5 4.0 195XTV 65.5 37.6 26.9 21.0 17.3 14.7 11.3 9.4 7.9 5.0 240XTV 81.7 45.5 32.1 25 19.8 16.6 13 10.5 9 5.6 Estimated Runtime Minutes Using XM3-918HP (Deduct 4-6% for Legacy XM Power Supplies) 90VAC @ 4A 8A 12A 18A XTV Models 100 150 195 240 100 150 195 240 100 150 195 240 100 150 195 240 3 Batteries 280 401 506 581 133 190 245 289 81 117 153 188 47 69 92 118 6 Batteries 597 869 1083 1240 298 427 538 617 188 269 344 399 113 163 211 251 9 Batteries 914 1349 1673 1927 465 672 841 961 300 430 542 621 185 264 337 391 Estimated Runtime Minutes Using XM3-624HP (Deduct 4-6% for Legacy XM, VMX, and GMX Power Supplies) 60VAC @ 4A 8A 12A 18A XTV Models 100 150 195 240 100 150 195 240 100 150 195 240 100 150 195 240 3 Batteries 416 599 751 858 203 290 369 427 126 181 234 276 74 108 142 175 6 Batteries 869 1280 1588 1828 441 637 797 912 284 407 513 589 174 249 319 371 9 Batteries 1321 1941 2441 2832 681 995 1237 1419 444 461 803 918 278 398 503 577 Based on .92 cable plant factor @ 25°C / 77°F click photo to enlarge GigaTrue CAT6 Channel Patch Cable with Basic Connectors, Yellow, 20-ft. (6.0-m) Get CAT6 performance in an end-to-end Black Box® GigaTrue® channel. EVNSL624-0020 Extended Double Diamond™ Warranty Available (Lifetime) Product Highlights Get high-level CAT6 performance in an end-to-end BLACK BOX® GigaTrue® channel. • Meets or exceeds CAT6 specifications.• Tested to 550 MHz.• Guaranteed for life!• Click the tabs below for more information on this product. Description GigaTrue CAT6 Channel Patch Cable with Basic Connectors, Yellow, 20-ft. (6.0-m) Quick Facts Get high-level CAT6 performance in an end-to-end BLACK BOX® GigaTrue® channel. • Meets or exceeds CAT6 specifications.• Tested to 550 MHz.• Guaranteed for life!• Further Details Cable construction: stranded, 24 AWG copper wire, RJ-45 connectors, 4-pair, T568B, PVC jacket, straight-pinned. • Improved attenuation provides cleaner data and video transmissions.• For 1000BASE-T, 100BASE-TX, 100BASE-VG, 155-Mbps ATM, 100- Mbps FDDI/CDDI, and other high-speed applications. • Perfect for full broadband and baseband video.• Stranded cable delivers full Power Sum performance.• Provides full-duplex operation for next-generation applications.• Meets balance requirements (LCL/LCTL), resulting in better transmission. • NOTE: This product works with all standard jacks, wallplates, and other RJ-45 hardware. Questions? Contact our FREE Tech Support. This cable works with: GigaStation High-Density Multimedia Patch Panels• GigaTrue CAT6 Patch Panels• GigaTrue CAT6 Jacks• GigaTrue2 CAT6 Jacks• GigaStation Wallplates• GigaStation2 Wallplates• GigaStation2 Surface-Mount Housings• Snap Fittings• GigaStation2 Snap Fittings• Questions? Contact our FREE Tech Support. Technical Specifications for GigaTrue CAT6 Channel Patch Cable with Basic Connectors, Yellow, 20-ft. (6.0-m): Attenuation — 23.6 dB at 100 MHz; 39.1 dB at 250 MHz Conductor Gauge — 24 AWG Delay Skew (Maximum) — 25 ns/100 m (328 ft.) Impedance — 100 ± 15 ohms at 100 MHz; 100 ± 22 ohms at 100–550 MHz Mutual Capacitance — 56 pF/m (maximum) 1 Lifetime Included $14.95 Add to Cart Price: $14.95 Quantity Available: 59 Quantity Warranty Total Shipping Info In Stock - orders received before 5PM ET ship same day Weight: 0.5 lbs. HxWxD: 0.8 x 6 x 6 in. 45-day return policy Tip: Click here to open a list of our current online promotions. Back to Search Results Cables > Copper Patch Cables Yourshopping cart is empty Cable Selectors Use these handy tools to quickly find the exac CAT5/5e/6/6a/7, fiber, or custom cable—or custom adapter—you need. Choose a Selector: Details Tech Specs Resources Warranty Similar Products Page 1 of 3GigaTrue CAT6 Channel Patch Cable with Basic Connectors, Yellow, 20-ft. (6.0-m) - EV... 8/13/2013http://www.blackbox.com/Store/Detail.aspx/GigaTrue-CAT6-Channel-Patch-Cable-with-... Part # EVNSL624-0020 GigaTrue CAT6 Channel Patch Cable with Basic Connectors (Yellow) PDF Drawing PDF Drawing of the EVNSL624 Series Black Box Explains...Solid vs. stranded cable. Black Box Explains...What to look for in a channel solution. Black Box Explains...Category 5, 5e, and 6 copper wiring standards. Black Box Explains…Component vs. channel testing. Standard Manufacturer's Warranty A warranty is included. NEXT — 45.0 dB at 100 MHz; 39.0 dB at 250 MHz PS-ACR — 32 dB (typical) at 100 MHz PS-NEXT — 43.0 dB at 100 MHz; 37.0 dB at 250 MHz Resistance (Maximum) — 9.09 ohms/100 m (328 ft.) Return Loss — 22.5 dB at 100 MHz; 20.5 dB at 250 MHz Standards — TIA/EIA-568-B.2-1 Category 6 Structured Return Loss — 22.5 dB at 100 MHz; 20.5 dB at 250 MHz Cable construction: stranded, 24 AWG copper wire, RJ-45 connectors, 4-pair, T568B, PVC jacket, straight- pinned. Improved attenuation provides cleaner data and video transmissions. For 1000BASE-T, 100BASE-TX, 100BASE-VG, 155-Mbps ATM, 100-Mbps FDDI/CDDI, and other high-speed applications. Perfect for full broadband and baseband video. Stranded cable delivers full Power Sum performance. Provides full-duplex operation for next-generation applications. Meets balance requirements (LCL/LCTL), resulting in better transmission. NOTE: This product works with all standard jacks, wallplates, and other RJ-45 hardware. Questions? Contact our FREE Tech Support. This cable works with: GigaStation High-Density Multimedia Patch Panels GigaTrue CAT6 Patch Panels GigaTrue CAT6 Jacks GigaTrue2 CAT6 Jacks GigaStation Wallplates GigaStation2 Wallplates GigaStation2 Surface-Mount Housings Snap Fittings GigaStation2 Snap Fittings Questions? Contact our FREE Tech Support. NOTE: Technical specification weight is the unit weight. It is not the packaged shipping weight. For shipping weight, please contact Black Box customer service at 877-877-2269. Resources for GigaTrue CAT6 Channel Patch Cable with Basic Connectors, Yellow, 20- ft. (6.0-m): Pdf Drawings Black Box Explains Double Diamond™ Warranty (Standard) Coverage: Take the risk out of equipment purchases with the Double Diamond™ Warranty from Black Box Network Services. The Double Diamond™ Warranty is our no-questions-asked warranty that protects your Black Box® brand products* from accidental damage, including drops, water, and power surges. Most of our products come with a one- or two-year warranty. Some products—such as copper cables, manual switches, cabinets, and racks—are even guaranteed for life! During the warranty period, Black Box Network Services will repair or replace your damaged equipment within one week of receipt at NO CHARGE! Plus, get an Extended Double Diamond Warranty. You can also extend your warranty or protect a previously purchased Black Box® brand product* for an additional year—for only 10% of the purchase price! Or, extend your coverage for a full three years for only 20% of the purchase price! That's getting three years for the price of two. Ordering an extended warranty is easy: When viewing a product in your shopping cart, just select the one or three years of additional coverage in the dropdown menu under “Warranty Options.” For details, contact Customer Service at 724-746-5500. * Certain products may not be eligible. Warranty Compared Black Box® Double Diamond™ Warranty The Competition Warranty Length One Year to Lifetime, Depending on the Product. Read the fine print. Guaranteed for Life! Black Box® Brand Copper Cables, Manual Switches and More! No. Page 2 of 3GigaTrue CAT6 Channel Patch Cable with Basic Connectors, Yellow, 20-ft. (6.0-m) - EV... 8/13/2013http://www.blackbox.com/Store/Detail.aspx/GigaTrue-CAT6-Channel-Patch-Cable-with-... Vantage Edge®2 A machine vision processor that delivers superior performance State-of-the-art video detection processor The Vantage Edge®2 processor is a key component in the family of Vantage® video detection solutions. The module combines state-of-the-art technology with sophisticated algorithms to deliver dependable vehicle detection required for today’s complex transportation systems. The Edge2 processor features single, dual, or quad video inputs to maximize configuration efficiencies for intersection control, highway monitoring, and ramp metering flow control applications. Maximum flexibility with optional modules The processor module is complimented by multiple Input/Output and Extension Modules that provide flexible and expandable solutions to meet the needs of larger and more complex intersection configurations. The Edge2 processor module and its associated expansion modules fit into standard detector racks to simplify installation and set up. All modules are designed as a simple and cost-effective replacement for the inductive loop amplifier module configuration. Benefits of the Vantage Edge2 System Simple to use interface reduces training time and improves productivity Includes SmartCycle® bicycle detection and differentiation algorithms Ease of set up and minimal lane closure time reduces manpower cost and keeps traffic flowing during equipment installation Copyright © 2017 Iteris, Inc. All rights reserved. NOTICE: Iteris, Inc. reserves the right to change product specifications without notice. Information furnished is for informational purposes only. This information may not be complete or the latest revision. For the most up-to- date information, please contact Iteris, Inc. VantageEdge®2 A machine vision processor that delivers superior performance January 2017 Rev1SPECIFICATIONS The Edge2 processor and all of its associated modules can be completely configured by using a mouse and video monitor only, eliminating the need for expensive laptops or PDA devices. More Benefits • “Plug and play” operation enables use of existing detector rack • Expandable and modular system allows for optimal configuration that helps to reduce cost while preserving room for incremental growth Power Consumption 12 or 24 VDC, 7W maximum  @12VDC - 490mA  @24VDC - 280mA Video Input type NTSC, PAL  75 Ohm 1 Vpp 1 input channel  Single BNC connector 2 input channel  Dual BNC connector 4 input channel  DB15 video input connector (cable supplied) Output – All models  Single BNC connector Communication Ports Single/Dual Quad RS232 p USB A Mouse p p USB A Thumbdrive p USB B Comms p Detector I/O Outputs (open collector +24VDC nominal 50mA)  4 on rear edge of module Inputs  4 on rear edge of module 24 detection zones per camera channel Status Indicators 4 LEDs indicate output detection state 4 LEDs indicate video source Environmental -35oF to +165oF (-37oC to +74oC) 0% to 95% humidity non-condensing 0.5Gm, 3 axes, 5-30Hz vibration tested 10G in all 3 axes for shock testing Mechanical 7” L x 4.5” H x 2.31” W. (17.78cm x 11.43cm x 5.86cm) 0.8lb (.363Kg) Warranty 3 years limited warranty Regulatory NEMA TS-2 Compliant FCC part 15, Class A Vantage EdgeConnect™ Quad-view remote communications module Ethernet connectivity with streaming video Vantage EdgeConnectTM is a unique “technology first” product that enhances connectivity between systems in the field and a remote management system. Iteris’ EdgeConnect quad-view remote communications module provides both local and remote management of data and Vantage EdgeConnect Quad-view remote communications module video over Ethernet — enabling system operators to manage their Vantage® video detection systems more efficiently and effectively by allowing the user to view real-time video and move data from the field to a central location. Highly flexible for unique user experience Vantage EdgeConnect’s advanced MPEG4/H.264 video compression ability minimizes bandwidth usage, and is scalable to fit the bandwidth available. Data rates can be set as low as 32 kbps or as high as 7 Mbps. Variable video frame rates between 5 and 30 frames per second also allow the user to optimize the streaming video to fit their specific application. Benefits of Vantage EdgeConnect Quickly review the operation of an entire intersection on one screen Enhances connectivity between systems in the field and a remote management system Simple-to-use interface reduces training time and improves productivity Copyright © 2017 Iteris, Inc. All rights reserved. NOTICE: Iteris, Inc. reserves the right to change product specifications without notice. Information furnished is for informational purposes only. This information may not be complete or the latest revision. For the most up-to- date information, please contact Iteris, Inc. Vantage EdgeConnect™ Quad-view remote communications module The EdgeConnect module provides the ability to view up to four camera feeds through a single IP connection, enabling the user to quickly review the operation of an entire intersection on one screen. The easy-to-use, browser-based user interface simplifies the management of video streams.January 2017 Rev1SPECIFICATIONS Connections 4 BNC connectors for video input (via DB15 spider cable) 4 RJ45 Edge2 Extension Module interface 1 RJ45 Ethernet connector 1 EIA-232 local access port USB mouse port 1 BNC composite video out connector Mechanical Size 7.0” long, 4.5” high, 2.3” wide (17.8 cm long, 11.4 cm high, 5.8 cm wide) Weight 0.64 lbs. (0.29 kg) Temperature -35° F to +165° F (-37° C to +74° C) Humidity 0% to 95% non-condensing Vibration 0.5G, 3 axes, 5-30 Hz Shock 10G in all 3 axes Electrical 12/24 VDC (500/260 mA) - 6.25 W max Warranty 3 Years limited warranty More Benefits • MPEG4/H.264 video compression ability is scalable to fit the bandwidth available • “Plug and play” operation enables use of existing detector rack, minimizing the need for reconfiguring the controller cabinet • Ease of setup and remote access reduces time and cost of installation and maintenance of equipment • Single quad view video stream or four independent single streams Innovation for better mobility View | Collect | Manage | Report Innovation for better mobility Iteris’ VantageView is the ultimate tool to complement your Iteris video detection system, with the map-based functionality of a Traffic Management Center (TMC) and the cost savings of a remote, web-based video detector management and data collection tool — to provide unparalleled value for real-time traffic monitoring. In these times of doing more with less and striving to be more efficient with staff time and budgets, VantageView enables: ►►Remote traffic camera management and configuration ►►Traffic data collection ►►Viewing of as many as nine intersections at a time For the city, county, regional, provincial, state, or federal agency, VantageView provides all of the functionality needed to manage highway and intersection video detection remotely. Access can be granted to VantageView users on a continuous or an as-needed basis for emergencies, temporary assignments, or long-term contracts. VantageView™ Agencies Need VantageView™ VantageView’s map-based functionality makes it simple to see where detectors are located and easy to click and view the camera’s video feed. VantageView becomes a powerful tool for the agency that doesn’t need a costly central management facility, or one who needs the ability to access some of their most critical TMC information on a laptop. Sensor Management, Data Collection, and Surveillance Applications include: ►►Remote Configuration of Video Cameras ►►Real-time street and intersection surveillance ►►Data collection (traffic and turning movement counts) ►►Average Daily Traffic (ADT) statistics ►►Average Annual Daily Traffic statistics (AADT) ►►High Performance Monitoring System (HPMS) report ►►Average Summer Daily Traffic (ASDT) ►►Vehicle Miles Traveled (VMT) ►►Monthly Average Daily Traffic (MADT) VantageView can also function as a remote, web-based, laptop emergency street surveillance management tool for law enforcement, Homeland Security, natural disaster, or civil unrest issues VantageView’s data collection tool enables agencies to acquire accurate turning movement counts and traffic flow data from highways and intersections. Volume, speed, occupancy, vehicle size, and video status data can be collected, time and date stamped, and recorded. VantageView’s configurable dashboard displays include: ►►Data ►►Charts ►►Graphs ►►Live camera video feeds Desktop point-and-click functionality make it easy to see traffic count information or camera views that are most needed. Trending graphs, histograms, and links to camera configurations provide quick access to information that must be acted upon — providing information by lane, zone, and time frame. Data can be exported for further analysis or reporting using additional software or processing programs. Traffic Data Collection & Reporting Helping agencies generate the following reports:Homeland Security or Emergency Management: Innovation for better mobility ►►Web-based — making access easy from internet connections ►►Map-centric — saves time and allows quick, visual locating of video detectors ►►Works with: ►» Iteris EdgeConnect, eAccess ►» Select 3rd party communication devices ►►One mouse click access to live video Benefits ►►Real time visual monitoring of roads or intersections using video camera feeds ►►Remote configuration capability reduces the need to dispatch workers to the field ►►Easy, centralized configuration of zones and camera setup functions to optimize performance straight from the desktop in the traffic center or any other location with web access View the Streets VantageView provides camera data feeds in a variety of configurations. With VantageView’s intuitive graphical user interface (GUI), users can archive video and intersection configuration information, as well as collect, store, and further process field data into actionable information from one central location. Drag and drop functionality allows a user to drag a smaller view into a larger window or mosaic as many as nine camera views into a three by three matrix to keep an eye on nine camera feeds at one time. Using a web-based and map-centric approach, VantageView allows the user to see a street map display or ‘bird’s eye view’ of the road network with all devices. Working with Iteris’ EdgeConnect™ remote communications module, VantageView allows the user to view streaming video of each connected and compatible camera. One mouse click provides real-time access to live video to see what is happening in the streets. ►►Excellent return on investment versus field maintenance calls and manual data collection ►►Obtain video detector operational status from any web connection ►►Centralized maintenance scheduling and record keeping ►►Remote configuration of video detection devices from any web connection ►►Multiple users can access VantageView over a standard web browser from any location with Internet access VantageView’s device management capabilities reduce the need to send staff into the field to reconfigure video detectors. The system provides for easy, centralized configuration of zones and camera setup functions to optimize performance, right from the desktop in the traffic center or any other location with internet access. This includes the ability to: ►►Capture camera characteristics and settings ►►Schedule maintenance ►►Configure camera settings ►►Create zones ►►Monitor video feeds The ability to manage sensor assets remotely saves agency staff and travel time as well as keeps field technicians out of harm’s way and inclement weather. Employees are more productive and liability exposure can be reduced. Remote Detector Configuration & Management Innovation for better mobility VantageView is a web-based application that works seamlessly with Iteris’ Vantage® video detection systems and many other cameras as well. With its comprehensive central management capabilities for managing and configuring Iteris Video detectors, a powerful data collection function and a highly configurable reporting engine, VantageView can deliver a significant return on investment in short order. In addition, VantageView can be pre-loaded on its own server, for ease of installation, to get the system up and running quickly, or it can be provided for your server. Designed by leaders in the traffic management and sensors industry, with over 80,000 detectors installed in over 20 countries worldwide, VantageView has the power to cut costs, streamline traffic flow, and reduce the risks and liability of field maintenance. Technologically Superior Software Technical Specifications System: Multi-user, web based Browser: Internet Explorer 8 Server Processor: Intel Xeon® X3430, 2.4 GHz Server RAM: 4 GB, 1333 MHz Server Hard Drive: 250 GB Server Mounting: Standard Rack Mount Server Network Adapter: On-Board Dual Gigabit Server Database: Microsoft® SQL Server™ 2008 Express Server Operating System: Win 7 Professional, 32 Bit Iteris has a broad and modular product line that allows users to tailor our detection systems for specific applications and controller cabinet configurations. Our large selection of easy- to-use, high performance, and cost-effective hardware options suit a wide variety of requirements. ►►Broad product portfolio offering unprecedented versatility and value ►►Industry-leading performance, functionality, and ease-of-use ►►Superior product support ►►Dedication to quality — ISO 9001:2008 certified Iteris’ highly-trained and IMSA-certified product support engineers support the deployment and maintenance of our video detection systems. Our nationally-recognized team has an outstanding reputation for superior installation, maintenance, and trouble-shooting, and can provide on-the- spot field training, when necessary. Why Iteris? By applying advanced engineering, experience, and imagination, Iteris develops end-to-end solutions that solve traffic problems today and allow for future growth and flexibility. Innovation for better mobility Sensor Management, Data Collection, and Surveillance Iteris’ VantageView is the ultimate tool to complement your Iteris video detection system, with the map-based functionality of a Traffic Management Center (TMC) and the cost savings of a remote, web- based video detector management and data collection tool — to provide unparalleled value for real-time traffic monitoring.> < Iteris Roadway Sensors Toll-free | 888-867-2288 Direct | 949-270-9400 www.iteris.com Building critical traffic connectionssm OPTICOM™ PRIORITY CONTROL SYSTEM OPTICOM™ MODEL 764 MULTIMODE PHASE SELECTOR OPTICOM™ SYSTEM COMPONENT FOR ENVIRONMENTS WITH INFRARED AND GPS TECHNOLOGY Description The Opticom™ Model 764 Multimode Phase Selector is a plug-in, four-channel, dual-priority, multimode encoded signal device designed for use with both Opticom™ infrared system emitters and detectors and Opticom™ GPS radio/GPS intersection units and vehicle equipment. It can be installed directly into the input files of Type 170 traffic controllers equipped with priority phase selection software and in virtually any other traffic controller equipped with priority phase selection inputs and related software. Phase selectors are powered from AC mains or 24 VDC and contain their own internal power supply to support Opticom™ infrared system detectors and Opticom™ GPS radio/GPS units. The Opticom™ Model 764 may be used in IR only applications, GPS only applications, or IR and GPS applications simultaneously. The Opticom™ Model 760 Card Rack is required when input file space is not available. When used in GPS only mode, the Model 1040 card rack may also be used. Opticom™ Model 764 recognizes and discriminates among three distinct Opticom™ IR emitter frequency rates via Opticom™ detectors: high priority, low priority and probe priority. Within each of these three frequency rates, the phase selectors further discriminate among 10 classes of vehicle identification codes, with 1,000 individual vehicle codes per class — 10,000 total per frequency rate. The Opticom™ Model 764 also recognizes three different priority levels transmitted by Opticom™ GPS vehicle equipment: high priority, low priority and probe priority. Within each of these three priority levels, the phase selectors further discriminate among 254 agency IDs, 15 classes of vehicle identification codes, with 10,000 individual vehicle codes per class — for more than 38 million total per priority level. Opticom™ Model 764 Phase Selector internally records each system activation. Each entry contains: • Intersection name • Date and time of the activity • Vehicle class code of the activating vehicle • Activating vehicle’s ID number • Agency ID (GPS only) • Channel called • Priority of the activity • Final green signal indications displayed at the end of the call • Time spent in the final greens • Duration of the activation • If preempt has been requested and reason if not • Turn signal status at the end of the call (GPS only) • Entry, exit and average speed (GPS only) • Relative priority level • Capability to playback up to the last 250 seconds of the 100 most recent calls Global Traffic Technologies, LLC (GTT), formed in 2007 from 3M’s pioneering Intelligent Transportation Systems business, is the manufacturer of Opticom™ priority control systems and Canoga™ traffic sensing systems. Features • IR only operation, GPS only operation, or simultaneous IR and GPS operation • Four channels of detection • Two auxiliary detectors per channel (IR) • Records green signal displayed at end of preemption • Compatible with encoded signal and non-encoded signal Opticom™ IR Emitters • High and low priority as well as probe frequency discrimination • “First-come, first-served” priority within each priority level • Priority-by-class setting via the interface software • Priority-by-direction setting via the interface software • Direct installation into CA/NY Type 170 input files • Automatic range setting using an encoded emitter (IR) • Call bridging for both IR and GPS calls including mixed mode • Low-priority output may be configured for first-come, first-served or all-channel active • User-adjustable range setting up to 2,500 feet of operation • Compatible with most traffic controllers • 10/100Mb Ethernet communication on the front panel • USB 2.0 communication on the front panel • RS232 communications front port, and rear backplane and Auxiliary Interface Panel • User-selected communications baud rate of 1,200 to 230,400 bits per second • Customizable ID code validation • Flexible programming options for priority control parameters • Detailed current Opticom™ System parameter information • History log of most recent Opticom™ infrared and GPS system activities (10,000 entries) • Call playback-logs 100 of the most recent calls-250 seconds long • 30,000 frequency/class/vehicle code ID combinations (IR) • More than 38 million agency/class/vehicle code combinations (GPS) • Front panel switches and diagnostic indicators for testing • Accurate infrared signal recognition circuitry • Precise output pulse • Definitive call verification • Regulated detector power supply (IR) • Optically isolated outputs • Two character display and keypad to enable diagnostics and test calls to each channel • Display LED Indicators - High- and low-priority test calls - Reset to default parameters - Range setting • User-settable range setting by ETA and/or distance (GPS only) • Varied outputs depending on turn signal status of requesting vehicle (GPS only) • Diagnostic test • Advanced built-in diagnostics and testing • Tested to NEMA and Caltrans environmental and electrical test specifications Accessories • On-site Interface software package • Model 768 Auxiliary Interface Panel • Opticom™ Model 755 Four-Channel Adapter Card (optional) • 760 Card Rack Operating Parameters • Four dual-priority and probe frequency channels • “First-come, first-served” for vehicles with the same priority level (high or low) • Priority override: always higher over lower • Opticom™ GPS Radio/GPS Unit input • Opticom™ Infrared System Detector input(s): one per channel on the card edge connector and two auxiliary per channel through the Model 768 auxiliary interface panel • Optional interface software for flexible programming options and call history • LED indicators - Status - Radio (GPS mode) - Link (GPS mode) - High signal/call per channel - Low signal/call per channel - Two-digit status display • Two character display and keypad to enable diagnostics and test calls to each channel • Voltage: 89 to 135 VAC, 60 Hz at up to 500mA or 24 VDC at up to 1 Amp • Temperature: -37°C to +74°C (-34.6°F to +165.2°F) • Humidity: 5% to 95% relative • CE certified • NEMA TS-2 compliance • FCC compliance Physical Dimensions Length: 7.0 in. (17.8 cm) x 8.2 in. (20.8 cm) including handle Width: 2.3 in. (5.8 cm) Height: 4.5 in. (11.4 cm) Weight: 0.60 lbs. (272 g) For complete warranty information visit www.gtt.com. OPTICOM™ MODEL 764 MULTIMODE PHASE SELECTOR OPTICOM™ SYSTEM COMPONENT FOR ENVIRONMENTS WITH INFRARED AND GPS TECHNOLOGY Building critical traffic connectionssm Global Traffic Technologies, LLC 7800 Third Street North St. Paul, Minnesota 55128-5441 1-800-258-4610 651-789-7333 www.gtt.com Opticom and the GTT logo mark are trademarks of Global Traffic Technologies, LLC. Used under license in Canada. Please recycle. Printed in U.S.A. © Global Traffic Technologies, LLC 2011 All rights reserved. 79-1000-0524-0 (A) Global Traffic Technologies Canada, Inc. 157 Adelaide Street West Suite 448 Toronto, ON M5H 4E7 Canada 1-800-258-4610 Building critical traffic connectionssm OpticOm™ priOrity cOntrOl SyStem OpticOm™ mOdel 768 AuxiliAry interfAce pAnel OpticOm™ SyStem cOmpOnent fOr envirOnmentS with infrared and GpS technOlOGy description Opticom™ Model 768 Auxiliary Interface Panel (AIP) provides a convenient method to interconnect Opticom™ Model 762 and 764 Phase Selectors with terminals inside a traffic cabinet. The 768 AIP is designed specifically for use with the Model 762 and 764 phase selectors. It is not intended to be used with other model phase selectors. The Opticom™ Model 768 contains terminal blocks for wiring to the traffic cabinet signals, two DB-9 RS-232 communication ports, and a 44-pin connector for connecting legacy auxiliary interface panels and auxiliary harnesses. A twelve foot cable is included which connects the AIP to the Model 762 or 764 Phase Selector. Global traffic technologies, llc (Gtt), formed in 2007 from 3m’s pioneering intelligent transportation Systems business, is the manufacturer of Opticom™ priority control systems and canoga™ traffic sensing systems. features • Accessible interconnections to cabinet wiring along the edge of card • Rugged construction - circuit card affixed to 16 AWG aluminum mounting plate • Connectors for auxiliary detector inputs and power can accommodate 16 to 28 AWG wires • Connectors for all other inputs and outputs can accommodate 16 to 22 AWG wires • Easy-to-read terminal designations Applications: The Model 768 AIP is used when any of the following features and/or capabilities is needed: • Green sensing or green light verification • Auxiliary infrared detector inputs • Additional preempt outputs - Turn signal dependent operation (For 764 in GPS operation) - Separate outputs for high and low priority • Clock sync input (In IR operation) • Clock sync output (For 764 in GPS operation) • Confirmation light outputs • Disable outputs • Two additional RS-232 COM ports - GPS data input (In IR operation) - GPS data output (For 764 in GPS operation) - Additional Serial COM port The Model 768 AIP includes a connector for connecting an existing auxiliary harness or auxiliary interface panel to green sense and/or auxiliary detectors. Simply remove the old AIP or harness and connect it directly to the 768. If the existing harness or AIP is being used for other functions, it will be necessary to move the wires to the Model 768 AIP. physical dimensions Length: 7.25 in. (18.4 cm) Width: 4.5 in. (11.4 cm) Height: 1.0 in. (2.5 cm) Weight (with cable): 1.4 lbs. (635 g) Cable: 12 ft (3.6M) For complete warranty information visit www.gtt.com. Global Traffic Technologies, LLC 7800 Third Street North St. Paul, Minnesota 55128-5441 1-800-258-4610 651-789-7333 www.gtt.com Opticom and the Gtt logo mark are trademarks of Global traffic technologies, llc. Used under license in canada. please recycle. printed in U.S.A. © Global traffic technologies, llc 2011 All rights reserved. 79-1000-0656-0 (A) Global Traffic Technologies Canada, Inc. 157 Adelaide Street West Suite 448 Toronto, ON M5H 4E7 Canada 1-800-258-4610 ENGINEERING INC.9153 STELLAR CT., CORONA, CA 92883 (888) 340-4872 © 2017 Polara Engineering, Inc. Doc. iCCU-C Rev. A-24681 01/20/2017 Page 1 of 1 www.polara.com iCCU-C – iNTELLIGENT CENTRAL CONTROL UNIT RACK MOUNT CARD The iCCU-C is designed for use in Cal-Trans or 300 Series cabinets and is the intelligent control unit for Polara’s iN2 accessible push button stations (PBS). The system is provided with a special cable adapter which detects the low voltage pedestrian load switch control signals present on the C4 connector. The special cable adapter (P/N: 850-382) connects between C4S and C4P and routes to the iCCU-C front panel. The iCCU-C installs in the input file in place of the typical pair of Type 242 isolators used for pedestrian detection. A small interconnect panel (P/N: iN2-ICB-C) provides connection to 16+ PBSs. Each iN2 PBS requires only two wires. All PBSs connect in parallel and do not have a polarity requirement. A required separate power supply (P/N: iN2-150WPS-C) connects to the interconnect panel to power the iN2 PBSs. The iCCU-C front panel includes a backlit LCD for displaying system status information. Front panel buttons are used during setup, placing test calls, and to enable Wi-Fi. All setup functions can be performed via Ethernet or Wi-Fi using a PC. Setup is also supported using an iPhone or iPad via Wi-Fi. In addition, configuration via Bluetooth is supported by pairing with any connected iN2 PBS using a PC, iPhone, or iPad. All of the connection options provide full access to setup and configuration of both the iCCU-C and all connected iN2 PBSs. Polara provides free apps for both Windows PCs (Win 7+) and iOS (8.0+) devices. Multiple configurations are supported, with the ability to change operational features based on time of day. The system has internal conflict monitoring and health log data capture that is both downloadable and contains extensive status/fault reporting. Remote Monitoring can be done over Ethernet. Ped Walk / Don’t Walk Inputs: 0 – 24 VDC (Active Low) Ped Outputs: Optically Isolated 36 Volts AC/DC peak 300mA Solid State Fused Contact Closure Environmental: Operating: -34ºC (-30ºF) to +74ºC (+165ºF)* Storage: -45ºC (-50ºF) to +85ºC (+185ºF) Warranty: 3 year limited *The LCD temperature range is limited to -20°C to +70°C operational. Dimensions are in inches. All dimensions are reference only and subject to change without notice. Notes:1. The iCCU-C is compatible with Cal-Trans TEES and 300 Series cabinets with a standard C4 connection to the output file.2. Preemption messaging though the APS system is not available on this unit. 2.29 4.50 6.98 1.17 This Interconnect Board and Power Supply (purchased separately, PN iN2-150WPS-C) is required for landing of intersection/field button wires when an iCCU-C Control Unit is used. Allows for connection of up to 16 iN2 pushbutton stations. The Power Supply connects to the Interconnect Board and provides the necessary additional power to operate the push button stations. The part number for ordering the interconnect board is iN2-ICB-C. The part number for ordering the power supply is iN2-150WPS-C. iN2-ICB-C: Interconnect Board for iCCU-C www.polara.com Dimensions are in inches. www.polara.comDoc. IN2-ICB-C-CutSheet Rev. A 03/17/17 ENTERPRISES www.polara.com Dimensions are in inches. www.polara.comDoc. IN2-ICB-C-CutSheet Rev. A 03/17/17 ENTERPRISES iN2-C4-CABLE-C: This cable is used to interface the iCCU-C to a 300 series traffic cabinet. The C4 cable connects between the existing C4 socket and C4 plug in the cabinet and routes the low voltage load switch outputs to the front of the iCCU-C. www.polara.com Dimensions are in inches. www.polara.comDoc. iN2-C4-CABLE-C-CutSheet Rev. A 03/17/17 ENTERPRISES www.polara.com Dimensions are in inches. www.polara.comDoc. iN2-C4-CABLE-C-CutSheet Rev. A 03/17/17 ENTERPRISES Mechanical Specifications: Supply’s enclosure is rated for IP67 or greater protection from ingress of water and dust.• Overall dimensions of the enclosure, excluding cabling, does not exceed 9” long x 3” wide x 2” tall.• Electrical Specifications: Input/Output Isolation meets or exceeds 2500 VDC• Nominal power supply rating of 150W• Input supply range of 90 to 130 VAC• Input Frequency 50/60Hz +/- 2 Hz• NEMA operating temperature range of -34 C to +74 C• Supply output is 24 VDC +/- 2 V over operating temperature range• CE/UL Certified• Short Circuit/Overcurrent Protection• iN2-150WPS-C: This power supply is used in conjunction with the iN2-ICB-C interconnect board to power 2 Wire iNavigators connected to an iCCU-C. www.polara.com Dimensions are in inches. www.polara.comDoc. iN2-150WPS-C-CutSheet Rev. A 03/17/17 ENTERPRISES ALPHA WIRE COMPANY CUSTOMER PRODUCT SPECIFICATION Part Number: 775 Issue: 3 Page 1 of 2 Pages Issue Date: 5/25/2004 Effective Date: 6/30/2004 A. Cordage Construction 1) Conductor a) Material Bare Copper, per ASTM B-3 b) AWG, Stranding 18, 41/34; Finer stranding may be used. 2) Insulation a) Material Rubber b) Min. Avg. Wall Thickness 0.015 c) Nominal Diameter 0.077 3) Core Assembly a) Number of Conductors 3 b) Color Code Black, White & Green/Yellow or Black, White & Green within Munsell® Component extended limits of deviation. [Note: The stripe of the Green/Yellow insulation shall be 50% +/- 20%.] c) Fillers Optional d) Separator Tissue Paper 4) Jacket a) Material Rubber b) Surface Finish Smooth, non-striated c) Min. Avg. Wall Thickness 0.030 d) Nominal Diameter 0.260 e) Color Black; within Munsell® Component limits of deviation f) UL, CSA Type SV**, Minimum g) Jacket Marking Per UL Standard 62 and CSA C22.2 No. 49. ** Cordage Types with a UL/CSA rating greater than Type SV may be substituted. B. Cord Configuration 1) End 1 Molded Vinyl Grounding Plug, NEMA 5-15P 2) End 2 Jacket Stripped 1.5” +/- .125” Insulation Stripped 0.625” +/- 0.0625” 3) Mold Color Black 4) Overall Length 72” +/- 1” Part # 99-43-0008-001 ALPHA WIRE COMPANY CUSTOMER PRODUCT SPECIFICATION Part Number: 775 Issue: 3 Page 2 of 2 Pages Issue Date: 5/25/2004 Effective Date: 6/30/2004 C. Industry Approvals and Ratings 1) UL UL Standard 817 2) CSA CSA C22.2 No. 21 3) Voltage Rating 125 Vrms 4) Current Rating 10 Amps 5) Temperature Rating 60°C, Minimum www.RuggedCom.com 1RuggedSwitchTMRS940G RuggedSwitchTM RS940G 8-Port Managed Gigabit Ethernet Switch The RuggedSwitch™ RS940G is an industrially hardened, fully managed Ethernet switch providing six or eight ports of Gigabit Ethernet. Six 10/100/1000BaseTX triple speed copper ports are standard. An additional two gigabit fiber or copper ports can be added. The RS940G provides a cost effective way of connecting a cluster of field devices to a Gigabit Ethernet backbone. Designed to operate reliably in harsh industrial environments the RS940G provides a high level of immunity to electromagnetic interference and heavy electrical surges typical of environments found in electric utility substations, process control or in curb side traffic control cabinets. An operating temperature range of -40°C to +85°C coupled with hazardous location certification, optional conformal coating and a galvanized steel enclosure allows the RS940G to be placed in almost any location. The embedded Rugged Operating System (ROSTM) provides advanced networking features such as Enhanced Rapid Spanning Tree (eRSTPTM), Port Rate Limiting and a full array of intelligent functionality for high network availability and manageability. The versatility and wide selection of fiber optics allows the RS940G to be used in a variety of applications. The RS940G provides two fiber optical Gigabit Ethernet ports for creating a fiber optical backbone with high noise immunity and long haul connectivity. The embedded Rugged Operating System (ROS™) provides advanced layer 2 and layer 3 networking functions, and advanced cyber security features. Coupled with the ruggedized hardware design, RS940G is ideal for creating mission-critical, real-time, control applications where high reliability and availability is of paramount importance. Ethernet Ports .6 - 10/100/1000BaseTX Triple Speed Copper Ports Standard .Optional 2 additional 1000LX SFP Pluggable Gigabit Fiber .2 - 10/100/1000BaseTX copper ports .Long haul optics allow Gigabit distances up to 70km Cyber Security Features .Multi-level user passwords .SSH/SSL encryption .Enable/disable ports, MAC based port security .Port based network access control (802.1x) .VLAN (802.1q ) to segregate and secure network traffic .Radius centralized password management .SNMPv3 encrypted authentication and access security RuggedRatedTM for Reliability in Harsh Environments .Immunity to EMI and heavy electrical surges .Meets IEEE 1613 (electric utility substations) .Exceeds IEC 61850-3 (electric utility substations) .Exceeds IEC 61800-3 (variable speed drive systems) .Exceeds IEC 61000-6-2 (generic industrial) .Exceeds NEMA TS-2 (traffic control equipment) .Hazardous Location Certification: Class 1 Division 2 .-40 to +85°C operating temperature (no fans) .Conformal coated printed circuit boards (optional) Rugged Operating System (ROSTM) Features .Simple plug and play operation - automatic learning, negotiation, and crossover detection .RSTP (802.1w) and Enhanced Rapid Spanning Tree (eRSTP™) network fault recovery (<5ms) .Quality of Service (802.1p) for real-time traffic .VLAN (802.1q) with double tagging and GVRP support .Link aggregation (802.3ad) .IGMP Snooping for multicast filtering .Port Rate Limiting and Broadcast Storm Limiting .Port configuration, status, statistics, mirroring, security .Industrial automation features (eg. Modbus) Management Tools .Web-based, Telnet, CLI management interfaces .SNMP v1/v2/v3 .Remote Monitoring (RMON) .Rich set of diagnostics with logging and alarms Universal Power Supply Options .Fully integrated power supply .Universal high-voltage range: 88-300VDC or 85-264VAC .Dual low-voltage DC inputs: 24VDC (9-36VDC) or 48VDC (36-72VDC) .Terminal blocks for reliable maintenance free connections .CSA/UL 60950 safety approved to +85°C ISO 9001:2000ISO 9001:2000ISO 9001:2000 CERTIFIED RUGGEDCOM eRSTPeRSTPeRSTPeRSTPeRSTP TM eRSTPeRSTP eRSTPeRSTP Features and Benefits eRSTPeRSTP eRSTPeRSTP www.RuggedCom.com 2RuggedSwitchTMRS940G RuggedSwitchTM RS940G 8-Port Managed Gigabit Ethernet Switch Optional Dual Gigabit Fiber Ports: Pluggable Optics (SFP) LC or SC connectors Distances up to 70km Integrated Power Supply Universal high-voltage range: 88-300VDC or 85 - 264VAC Popular low voltage DC ranges: 24VDC (9-36VDC), 48VDC (36-59VDC) Dual Isolated DC power inputs Gigabit Copper Ports: 6 - Triple Speed Copper Ports (10/100/1000BaseTX) Critical Alarm Relay Form-C failsafe contact relay: 1A@30VDC RuggedSwitch™ RS940G Rugged Construction: 20 AWG. galvanized steel enclosure Conformal coating (optional) Operating Temperature -40oC to +85oC No Fans Mounting Options Din Rail Panel Mount Hazardous Location Certification Class1, Division2 www.RuggedCom.com 3RuggedSwitchTMRS940G RuggedSwitchTM RS940G 8-Port Managed Gigabit Ethernet Switch Cyber Security Cyber security is an urgent issue in many industries where advanced automation and communications networks play a crucial role in mission critical applications and where high reliability is of paramount importance. Key ROS™ features that address security issues at the local area network level include: .Passwords - Multi-level user passwords secures switch against unauthorized configuration .SSH / SSL - Extends capability of password protection to add encryption of passwords and data as they cross the network .Enable / Disable Ports - Capability to disable ports so that traffic can not pass .802.1q VLAN - Provides the ability to logically segregate traffic between predefined ports on switches .MAC Based Port Security - The ability to secure ports on a switch so only specific Devices / MAC addresses can communicate via that port .802.1x Port Based Network Access Control - The ability to lock down ports on a switch so that only authorized clients can communicate via this port .Radius - Provides centralized password management .SNMPv3 - encrypted authentication and access security The ROS™cyber security features are included to help address the various industry specific security standards such as NERC CIP, ISA S99, AGA 12, IEC 62443, ISO 17799:2005 and PCSRF SPP-ICS. Enhanced Rapid Spanning Tree Protocol (eRSTP™) RuggedCom eRSTP allows the creation of fault-tolerant ring and mesh Ethernet networks that incorporate redundant links that are 'pruned' to prevent loops. eRSTP yields worst-case fault recovery1 of 5ms times the 'bridge diameter' and allows rings of up to 80 switches. For example, a ring of ten switches will have fault recovery times under 50ms. eRSTP implements both STP and RSTP to ensure interoperability with commercial switches unlike other proprietary 'ring' solutions. Quality of Service (IEEE 802.1p) Some networking applications such as real-time control or VoIP (voice over IP) require predictable arrival times for Ethernet frames. Switches can introduce latency in times of heavy network traffic due to the internal queues that buffer frames and then transmit on a first come first serve basis. ROS™ supports 'Class of Service' in accordance with IEEE 802.1p that allows time critical traffic to jump ahead to the front of the queue thus minimizing latency and reducing jitter to allow such demanding applications to operate correctly. ROS™allows priority classification by port, tags, MAC address, and IP type of service (TOS). A configurable "weighted fair queuing" algorithm controls how frames are emptied from the queues. VLAN (IEEE 802.1q) Virtual local area networks (VLAN) allow the segregation of a physical network into separate logical networks with independent broadcast domains. A measure of security is provided since hosts can only access other hosts on the same VLAN and traffic storms are isolated. ROS™ supports 802.1q tagged Ethernet frames and VLAN trunks. Port based classification allows legacy devices to be assigned to the correct VLAN. GVRP support is also provided to simplify the configuration of the switches on the VLAN. Link Aggregation (802.3ad) The link aggregation feature provides the ability to aggregate several Ethernet ports into one logical link (port trunk) with higher bandwidth. This provides an inexpensive way to set up a high speed backbone to improve network bandwidth. This feature is also known as "port trunking", "port bundling", "port teaming", and "ethernet trunk". IGMP Snooping ROS uses IGMP snooping (Internet Group Management Protocol v1&v2) to intelligently forward or filter multicast traffic streams (e.g. MPEG video) to or from hosts on the network. This reduces the load on network trunks and prevents packets from being received on hosts that are not involved. ROS™ has a very powerful implementation of IGMP snooping that: .Can be enabled on a per VLAN basis. .Detects and filters all multicast streams regardless of whether subscribers exist. .Supports "router-less" operation by supporting an "active" mode. .Restores traffic streams immediately after an RSTP topology change. SNMP (Simple Network Management Protocol) SNMP provides a standardized method for network management stations the ability to interrogate devices from different vendors. SNMP versions supported by ROS™ are v1, v2c, and v3. SNMPv3 in particular provides security features (such as authentication, privacy, and access control) not present in earlier SNMP versions. ROS™ also supports numerous standard MIBs (Management Information Base) allowing for easy integration with any network management system (NMS). 1 eRSTP fault recovery times may be approximated as follows: For 100 Mbps, fault recovery performance is <5ms/hop For 1,000 Mbps, fault recovery performance is <5ms/hop + 20ms ROSTM Features www.RuggedCom.com 4RuggedSwitchTMRS940G RuggedSwitchTM RS940G 8-Port Managed Gigabit Ethernet Switch SNMP (Simple Network Management Protocol) (cont’d) A feature of SNMP supported by ROS™ is the ability to generate "traps" upon system events. A NMS can record traps from multiple devices providing a powerful network troubleshooting tool. RuggedVueTM is RuggedCom's NMS that provides graphical visualization of the network and is fully integrated with all RuggedCom products. SNTP (Simple Network Time Protocol) SNTP automatically synchronizes the internal clock of all ROS™ devices on the network. This allows for correlation of time stamped events for troubleshooting. SCADA and Industrial Automation ROS™ contains features that optimize network performance and simplify switch management based on the unique requirements found in SCADA and industrial automation applications. Features such as Modbus TCP management for retrieval of switch data using the ubiquitous Modbus protocol and DHCP Option 82, a Rockwell Automation ODVA requirement for IP address assignment based on the location of the end device, provide capabilities not found in typical "commercial" or "office grade" Ethernet switches. Port Based Network Access Control (802.1x) ROS™ supports the IEEE 802.1x standard that defines a mechanism for port-based network access control which provides a means of authenticating and authorizing devices attached to LAN ports. Port Rate Limiting ROS™ supports configurable rate limiting per port to limit unicast and multicast traffic. This can be essential to managing precious network bandwidth for service providers. It also provides edge security for denial of service (DOS) attacks. Broadcast Storm Filtering Broadcast storms wreak havoc on a network and can cause attached devices to malfunction. This could be disastrous on a network with mission critical equipment. ROS™ limits this by filtering broadcast frames with a user-defined threshold. Loss of Link Management Some intelligent electronic devices (IEDs) have dual fiber optic ports with automatic failover to a backup port should the primary fail. ROS™ ensures this mechanism works reliably under all failure modes by appropriately disabling link signals when required. ROS™ also flushes learned MAC addresses to ensure the failover occurs quickly. Port Mirroring ROS™can be configured to duplicate all traffic on one port to a designated mirror port. When combined with a network analyzer, this can be a powerful troubleshooting tool. Port Configuration and Status ROS™ allows individual ports to be 'hard' configured for speed, duplex, auto-negotiation, flow control and more. This allows proper connection with devices that do not negotiate or have unusual settings. Detailed status of ports with alarm and SNMP trap on link problems aid greatly in system troubleshooting. Port Statistics and RMON (Remote Monitoring) ROS™ provides continuously updating statistics per port that provide both ingress and egress packet and byte counters as well as detailed error figures. Also provided is full support for the RMON statistics, history, alarms, and event groups. RMON allows for very sophisticated data collection, analysis and detection of traffic patterns. Event Logging and Alarms ROS™ records all significant events to a non-volatile system log allowing forensic troubleshooting. Events include link failure and recovery, unauthorized access, broadcast storm detection, and self-test diagnostics among others. Alarms provide a snapshot of recent events that have yet to be acknowledged by the network administrator. An external hardware relay is de-energized during the presence of critical alarms allowing an external controller to react if desired. HTML Web Browser and Telnet User Interfaces ROS™ provides a simple, intuitive user interface for configuration and monitoring via a standard graphical web browser or via Telnet. All system parameters include detailed on-line help to make setup a breeze. ROS™ , presents a common look and feel and standardized configuration process allowing easy migration to other RuggedCom managed products. Configuration via ASCII Text File All configuration parameters are stored in an ASCII formatted text file that can easily be transferred via TFTP or Xmodem. The configuration file can be saved for backup purposes and easily manipulated by a text editor. The same text file can be downloaded to the switch at a later date in order to re-configure or restore a previous configuration. Command Line Interface (CLI) A command line interface can be used in conjunction with remote shell to automate data retrieval, configuration updates, and firmware upgrades. A powerful SQL-like capability allows expert users the ability to selectively retrieve or manipulate any parameters the device has to offer. ROSTM Features www.RuggedCom.com 5RuggedSwitchTMRS940G RuggedSwitchTM RS940G 8-Port Managed Gigabit Ethernet Switch EMI and Environmental Type Tests Environmental Type Tests Test Description Test Levels Severity Levels IEC 60068-2-1 Cold Temperature Test Ad -40°C, 16 Hours N/A IEC 60068-2-2 Dry Heat Test Bd +85°C, 16 Hours N/A IEC 60068-2-30 Humidity (Damp Heat, Cyclic)Test Db 95% (non-condensing), 55°C , 6 cycles N/A IEC 60255-21-1 Vibration Tests Fc 2g @ (10 - 150) Hz Class 2 IEC 60255-21-2 Shock Tests Ea 30g @ 11mS Class 2 IEC 61850-3 EMI TYPE TESTS TEST Description Test Levels Severity Levels IEC 61000-4-2 ESD Enclosure Contact +/- 8kV 4 Enclosure Air +/- 15kV 4 IEC 61000-4-3 Radiated RFI Enclosure ports 20 V/m x IEC 61000-4-4 Burst (Fast Transient) Signal ports +/- 4kV @ 2.5kHz x D.C. Power ports +/- 4kV 4 A.C. Power ports +/- 4kV 4 Earth ground ports 3 +/- 4kV 4 IEC 61000-4-5 Surge Signal ports +/- 4kV line-to-earth, +/- 2kV line-to-line 4 D.C. Power ports +/- 2kV line-to-earth, +/- 1kV line-to-line 3 A.C. Power ports +/- 4kV line-to-earth, +/- 2kV line-to-line 4 IEC 61000-4-6 Induced (Conducted) RFI Signal ports 10V 3 D.C Power ports 10V 3 A.C. Power ports 10V 3 Earth ground ports 3 10V 3 IEC 61000-4-8 Magnetic Field Enclosure ports 40 A/m continuous, 1000 A/m for 1 s N/A IEC 61000-4-29 Voltage Dips & Interrupts D.C. Power ports 30% for 0.1s, 60% for 0.1s, 100% for 0.05s N/A A.C. Power ports 30% for 1 period, 60% for 50 periods N/A IEC 61000-4-11 100% for 5 periods, 100% for 50 periods 2 N/A IEC 61000-4-12 Damped Oscillatory Signal ports 2.5kV common, 1kV diff. mode@1MHz 3 D.C. Power ports 2.5kV common, 1kV diff. mode@1MHz 3 A.C. Power ports 2.5kV common, 1kV diff. mode@1MHz 3 IEC 61000-4-16 Mains Frequency Voltage Signal ports 30V Continuous, 300V for 1s 4 D.C. Power ports 30V Continuous, 300V for 1s 4 IEC 61000-4-17 Ripple on D.C. Power Supply D.C. Power ports 10%3 IEC 60255-5 Dielectric Strength Signal ports 2kVac (Fail-Safe Relay output)N/A D.C. Power ports 2kVac N/A A.C. Power ports 2kVac N/A IEC 60255-5 H.V. Impulse Signal ports 5kV (Fail-Safe Relay output)N/A D.C. Power ports 5kV N/A A.C. Power ports 5kV N/A IEEE 1613 (C37.90.x) EMI IMMUNITY TYPE TESTS Test Description Test Levels Severity Levels IEEE C37.90.3 ESD Enclosure Contact +/- 8kV N/A Enclosure Air +/- 15kV N/A IEEE C37.90.2 Radiated RFI Enclosure ports 35 V/m N/A IEEE C37.90.1 Fast Transient Signal ports +/- 4kV @ 2.5kHz N/A D.C. Power ports +/- 4kV N/A A.C. Power ports +/- 4kV N/A Earth ground ports3 +/- 4kV N/A IEEE C37.90.1 Oscillatory Signal ports 2.5kV common mode @1MHz N/A D.C. Power ports 2.5kV common, 1kV diff. mode@1MHz N/A A.C. Power ports 2.5kV common, 1kV diff. mode@1MHz N/A IEEE C37.90 H.V. Impulse Signal ports 5kV (Fail-Safe Relay output)N/A D.C. Power ports 5kV N/A A.C. Power ports 5kV N/A IEEE C37.90 Dielectric Strength Signal ports 2kVac N/A D.C. Power ports 2kVac N/A A.C. Power ports 2kVac N/A Notes:1. Only applicable to functional earth connections separated from the safety earth connection. 2. Class 2 refers to "Measuring relays and protection equipment for which a very high security margin is required or where the vibration levels are very high, ( e.g. shipboard application and for severe transportation conditions") www.RuggedCom.com 6RuggedSwitchTMRS940G RuggedSwitchTM RS940G 8-Port Managed Gigabit Ethernet Switch Technical Specifications Power Supply .Power Consumption: 18W Max .24VDC: 9-36 VDC, 0.4A .48VDC: 36-72 VDC, 0.2A .HI Voltage AC/DC: 88-300VDC or 85-264VAC Critical Alarm Relay .Form-C failsafe contact relay: 1A@30VDC Physical .Height: 7.4" .Width: 2.6" .Depth: 5.0" .Weight: 2.7lbs .Ingress Protection: IP40 (1mm objects) .Enclosure: 20 AWG galvanized steel enclosure .Mounting: DIN rail or panel mounted Switch Properties .Switching method: Store & Forward .Switching latency: 7 us .Switching bandwidth: 5.6Gbps .MAC addresses: 8192 .MAC address table size: 32kbytes .Priority Queues: 4 .Frame buffer memory: 2 Mbit .VLANs: 4094 .IGMP multicast groups: 256 .Port rate limiting: 128kbps, 256, 512, 4, 8Mbps .No head of line blocking Approvals .Hazardous Locations: Class 1, Division 2 .ISO: Designed and manufactured using a ISO9001: 2000 certified quality program .CE Marking .Emissions: FCC Part 15 (Class A), EN55022 (CISPR22 Class A) .Safety: cCSAus (Compliant with CSA C22.2 No. 60950, UL 60950, EN60950) .Laser Eye Safety (FDA/CDRH): Complies with 21 CFR Chapter1, Subchapter J. Warranty .5 Years - Applicable to design and manufacturing related product defects. Network Management .HTTP graphical web-based .SNMP v1, v2c, v3 .Telnet, VT100 .Command Line Interface (CLI) EMI Immunity and Environmental Compliance .IEC 61000-6-2 Industrial (Generic) .IEC 61800-3 Industrial (Variable Speed Drive Systems) .IEC 61850-3 Electric Utility Substations .IEEE 1613 Electric Utility Substations .NEMA TS 2 Traffic Control Equipment (pending) IEEE Compliance .802.3-10BaseT .802.3u-100BaseTX, 100BaseFX .802.3x-Flow Control .802.3z-1000BaseLX .802.3ab-1000BaseTX .802.3ad-Link Aggregation .802.1d-MAC Bridges .802.1d-Spanning Tree Protocol .802.1p-Class of Service .802.1q-VLAN Tagging .802.1w-Rapid Spanning Tree Protocol .802.1x-Port Based Network Access Control IETF RFC Compliance .RFC768-UDP .RFC783-TFTP .RFC791-IP .RFC792-ICMP .RFC793-TCP .RFC826-ARP .RFC854-Telnet .RFC894-IP over Ethernet .RFC1112-IGMP v1 .RFC1519-CIDR .RFC1541-DHCP (client) .RFC2030-SNTP .RFC2068-HTTP .RFC2236-IGMP v2 .RFC2284-EAP .RFC2475-Differentiated Services .RFC2865-Radius .RFC3414-SNMPv3-VSM .RFC3415-SNMPv3-VACM IETF SNMP MIBS .RFC1493-BRIDGE-MIB .RFC1907-SNMPv2-MIB .RFC2012-TCP-MIB .RFC2013-UDP-MIB .RFC2578-SNMPv2-SMI .RFC2579-SNMPv2-TC .RFC2819-RMON-MIB .RFC2863-IF-MIB .draft-ietf-bridge-rstpmib-03-BRIDGE-MIB .draft-ietf-bridge-bridgemib-smiv2-03-RSTP-MIB .IANAifType-MIB www.RuggedCom.com 7RuggedSwitchTMRS940G RuggedSwitchTM RS940G 8-Port Managed Gigabit Ethernet Switch Fiber Specifications and Mechanical Drawing Fiber Optical Specifications Parameter Fiber Port Type Mode Multimode Singlemode Singlemode Singlemode Connector LC, LC-SFP SC, LC, LC-SFP SC, LC, LC-SFP LC-SFP Typical Dist.500m 10km 25km 70km Optical Wavelength (nm)850 1310 1310 1550 Cable SizeCore/Cladding (um)50/125 or 62.5/125 8/125 or 9/125 8/125 or 9/125 8/125 or 9/125 TX Power (Min/Max) (dBm)-9.5/-4 -9/-3 -7 / 3 0 / 5 RX Sensitivity (dBm)-20 -22 -26 -23 RX Saturation (dBm)0 -3 -3 0 Typical Budget (dB) 14 17 19 25 www.RuggedCom.com 8RuggedSwitchTMRS940G RuggedSwitchTM RS940G 8-Port Managed Gigabit Ethernet Switch Order Codes RS940G -__ - __ - ______ PS M P7P8 Base unit includes 6 - 10/100/1000 BaseTX ports PS: Power Supply .24 = 24 VDC (9-36 VDC) .48 = 48 VDC (36-72 VDC) .HI = 88-300VDC or 85-264VAC M: Mounting Option .D = DIN Rail .P = Panel Mount .N = None P7P8: Transceiver Options: XXXX = None 2TX = Dual 10/100/1000TX RJ45 2SFP = Dual 1000X SFP (Mini-GBIC). Order SFP Optics Separately. 2LCMM = Dual 1000SX Multimode LC 850nm 500m 2LC10 = Dual 1000LX Singlemode LC 1310nm 10km 2LC25 = Dual 1000LX Singlemode LC 1310nm 25km 2SC10 = Dual 1000LX Singlemode SC 1310nm 10km 2SC25 = Dual 1000LX Singlemode SC 1310nm 25km SFP (MINI-GBIC) Transceiver Options (1) (2): 25-10-0111 = 1000SX SFP, Multimode, LC, 850nm, 500m (1) (3) 25-10-0100 = 1000LX SFP, Singlemode, LC, 1310nm, 10 km (1) 25-10-0101 = 1000LX SFP, Singlemode, LC, 1310nm, 25 km (1) 25-10-0109 = 1000LX SFP, Singlemode, LC, 1550nm, 70 km (1) (3) NOTES 1 Distance ratings are typical but will depend on type of cabling, number of connectors and splices. 2 Should you not find an appropriate fiber optic option listed here, please consult RuggedCom for other options. 3 These transceivers have an operating temperature range of -20 to +85°C. All other transceivers have an operating temperature range of -40° to +85°C. Options 82-01-0002 - Conformal Coating RuggedCom Inc. 30 Whitmore Road Woodbridge, Ontario, Canada L4L 7Z4 Tel: (905) 856-5288 Fax:(905) 856-1995 Toll Free:(888) 264-0006 Technical Support Center: (866) 922-7975 or (954) 922-7975 © 2007 RuggedCom Inc. RuggedSwitch is a trademark of RuggedCom Inc. Ethernet is a trademark of the Xerox Corporation. Patent Pending All specifications in this document are subject to change without notice. Rev 1-C For additional information on our products and services, please visit our web site at: www.ruggedcom.com Part #RS940G-HI-2SFP Part # 25-10-0100 BEJED, INC 14325 NE Airport Way, Suite 101 Portland, Oregon 97230 503-281-8153 800-232-3533 Fax: 503-281-3339 sales@bejed.com http://www.bejed.com [5] Economy Fiber Optic Distribution Unit BJ-2113 18 - 24 Port Bay Mount Features Terminates 24 fibers with 8 port coupler plates 19 or 23 inch rack mount NEW! Flush Mount option available Improved fiber bend radii Slide out fiber termination shelf Multiple cable entrance/exit holes Low profile Ordering Information Application Our line of economy fiber optic distribution Units is designed for adaptability. The BJ-2113 can be configured for two or three coupler plates and are available with angled orientation for easier access. Aluminum construction for a lighter unit. Part Number Description BJ-2113B-002 FDU: 1RU, 3 Plates, White BJ-2113B-102 FDU: 1RU, 3 Plates, Black BJ-2113F-001 FDU: 1 RU, 2 Plates, White BJ-2113H-008 FDU: 1 RU, 2 Plates, Flush Mount, White Specifications Capacity: Two or Three Plates Dimensions: 1.75”H (1 UI) x 17”W x 11”D Weight: 4lbs. Construction: Aluminum Color: Off-White or Black Coupler Plates All BEJED Fiber Distribution Units are designed to use modular Coupler Plates allowing the type and quantity of fiber connections to meet the needs of the customer. Push rivets allow for easy installation. Plates can be provided with standard, hybrid fiber, RJ or modular couplers and dust caps are always included. Standard plates* are available for 6, 8 or 12 fibers. How to choose coupler plates: To determine the capacity of any of our FDUs, simply multiply the number of plates by the number of positions on each plate. Plates × Positions = Total Connections BJ-66ABC-DEE BJ-6662S-106 Coupler Plates All BEJED Fiber Distribution Units are designed to use modular Coupler Plates allowing the type and quantity of fiber connections to meet the needs of the customer. Push rivets allow for easy installation. Plates can be provided with standard, hybrid fiber, RJ or modular couplers and dust caps are always included. Standard plates* are available for 6, 8 or 12 fibers. How to choose coupler plates: To determine the capacity of any of our FDUs, simply multiply the number of plates by the number of positions on each plate. Plates × Positions = Total Connections BJ-66ABC-DEE 00 BJ-6660U-100 1122 Industry Street, Bldg B Phone (425) 438-1133 Everett, WA 98203 Fax (425) 438-1585 1 March 31, 2017 Prime Electric, Inc. 13301 SE 26th St Bellevue, WA 98005 Attention: Andrew Hollenback Regarding: City of Renton GHC Longacres Materials List –SUBMITTALS Bid Item #1; Traffic Signal System - SW 27th Street @ Naches Avenue SW DISPLAY EQUIPMENT: ITEM QTY DESCRIPTION 1 8 PPBS (iNavigator) 2-Wire system w/ 9x15 HIRR R-10-3E sign with voice and no braille (BLACK) Polara Eng. Part # IN23TN1-B 2 1 iNAV Bluetooth Dongle Polara Eng. Part# iN-DGL 3 6 3sec 12" Alum, Yellow Housing / Door w/ M mount, backplate, visors (RYG) General Traffic Part # NEW 4 2 4sec 12" Alum, Yellow Housing / Door w/ M mount, backplate, visors (RYG,G/Y<) General Traffic Part # NEW 5 4 Ped Signal, Alum, Yellow, Countdown, z-crate w/ E mount General Traffic Part # NEW 6 4 Ped Signal, Alum, Yellow, Countdown, z-crate w/ D mount General Traffic Part # NEW 7 4 Opticom 721 Detector 2 Barrel, 1 Channel GTT Part # 721 8 1 Opticom 138/100 Cable 1000 FT Roll GTT Part # 138/1000 4 9 Terminal Cabinet (WSDOT) Northwest Standard (2 Blocks) Western Part # 2020060000 Enclosed are (1) copy of submittal data sheets for the equipment on the above referenced project. Please return to Western Systems (1) submittal package with comments once approval has been granted. Any additional equipment required that changes the scope of the project will be addressed as a change order. Your order is currently not scheduled for a beginning delivery pending return of approved submittals. If a specific date is appropriate please confirm by written communication and we will do our best to meet your requirements. Sincerely, WESTERN SYSTEMS 1122 Industry Street, Bldg B Phone (425) 438-1133 Everett, WA 98203 Fax (425) 438-1585 2 Shawna Storms Estimator 2017W1570 / WSQ WA-SS509A © 2017 Polara Engineering, Inc. Doc. iN2 Rev. A.07-TBD 01/13/2017 Page 1 of 2 ENGINEERING INC.9153 STELLAR CT., CORONA, CA 92883 (888) 340-4872 www.polara.com iN2 – iNavigator 2-Wire Push Button Station The iN2 Navigator 2-Wire Push Button Station (iN2 PBS) is the pedestrian interface to the iNavigator Accessible Pedestrian System. Main components of a system consists of a Control Unit (P/N: iCCU-S or iCCU-C) and two or more Push Button Stations. The iN2 is an MUTCD compliant PBS, providing valuable information and cues via both a vibrating arrow button and audible sounds, making the intersection accessible for all pedestrians. All sounds emanate from both the front and the back of the unit. A sunlight-visible red LED latches “ON” along with a tactile feedback “bounce” to confirm the button has been pushed. The vandal-resistant designed iN2 PBS includes the body which houses the ADA compliant push button (shown), a faceplate (sign), and mounting hardware. By interfacing with the Control Unit that installs in the Traffic Signal Control Cabinet, the iN2 PBS can provide the following standard features: • Operates over a single pair of wires • All push button stations wired in parallel, individually assignable to any phase • 16+ buttons can operate with a single Control Unit* • All sounds are synchronized • 4 Locate Tone selectable options • 14 Walk Sound selectable options, 3 of them custom options • 7 Clearance Sound selectable options • Walk, Clearance and Don’t Walk sounds adjust automatically to ambient • Separate ambient response settings for Locate Tone (for quiet ambient conditions) • Most sounds have independent Min/Max settable limits • Button vibrates during Walk • Button push confirmed by latching LED, tactile bounce, and audible “wait” sound • Extended button push can boost volume for next Walk and Clearance • Direction of travel message with extended button push, capable • Extended Push Priority: Mutes all but selected crosswalk, capable • Extended Push Activation Settings: 0-6 second range, .5 second increments • Beaconing and Ping Pong features available • Select audio messages, change settings, and perform firmware updates wirelessly using iOS devices, or a Windows PC with Polara’s Bluetooth Dongle (P/N: iN-DGL) • Built in Health/Event logging feature, up to 300 events • False Walk Detection: Four independent checks • External Speaker-Option at time of order • External Button Input for bike lane, horses, etc. * Dependent on/limited by power requirements and wire runs 13.41 iN25BN0-Y unit shown. Dimensions are in inches. All dimensions are reference only and subject to change without notice. 6 5 2.3 © 2017 Polara Engineering, Inc. Doc. iN2 Rev. A.07-TBD 01/13/2017 Page 2 of 2 ENGINEERING INC.9153 STELLAR CT., CORONA, CA 92883 (888) 340-4872 www.polara.com Operating Specifications Parameter Rating Operating Temperature Range -34ºC to +74ºC (-30ºF to +165ºF) Storage Temperature Range -40ºC to +85ºC (-40ºF to +185ºF) Operating Force 3.0 lbs Maximum, three adjustable programmed forces are optional Switch Operating Life Greater than 20 Million Operations Maximum Volume 100 dB @ 1 meter Design Compliance Test Type Compliance Functionality MUTCD 2009 - 4E Temperature and Humidity NEMA TS 2* Transient Voltage Protection NEMA TS 2* Transient Suppression IEC 61000-4-4, IEC 61000-4-5* Electronic Noise (Bluetooth Radio)FCC Title 47, Part 15, Class A* Mechanical Shock and Vibration NEMA TS 2* iN2 PBS Enclosure NEMA 250 - Type 4X* Electrical Reliability NEMA TS 4 Notes: 1. Applicable sections only of reference standards. 2. All specifications are subject to change without notice. 3. All specifications are Typical unless otherwise specified.* Tested and Certified by independent 3rd party laboratory. Audio Message Options0 – Standard Messages1 – Custom Messages Braille N – No Braille on Face PlateB – Braille on Face Plate Size of Front Plate Adapter(Also chooses size of Faceplate, when present) 5 – 5” x 7¾” 9 – 9” x 12”3 – 9” x 15” Navigator Family iN2 – iNavigator 2-Wire Push Button Station Additional Available Options Button Options NA – No Arrow BD – Bi-Directional Arrow Other Options WPC – with Pole CapES – External Speaker Option Faceplate MUTCD Compliant Non-MUTCD CompliantV – 9x12 R10-3 A – 5x7 – InternationalU – 9x12 R10-3b B – 5x7 – InformationalT – 9x15 R10-3e C – 9x12 – Countdown D – 5x7 or 9x12 – International O – (Letter O) – No Faceplate ––iN2 5 A N 0 B BD–ES Button Cover Color (Back Plate and Body is always black. Button Cover color is designated by -B, -G, or -Y.)B – Black Button CoverG – Green Button Cover Y – Yellow Button Cover iN23TN1-G ENGINEERING INC.9153 STELLAR CT., CORONA, CA 92883 (888) 340-4872 © 2016 Polara Engineering, Inc. Doc. iN-DGL Rev. A. 24595 08/12/2016 Page 1 of 1 www.polara.com iNavigator Bluetooth Dongle The iNavigator Bluetooth Dongle (iN-DGL) was designed to enable any PC running Windows 7 or later to communicate with Polara’s iNavigator. The Dongle plugs into any USB port on your PC and utilizes Polara’s Intelligent Config PC App for communication. The Intelligent Config PC App can only communicate with iNavigator devices by utilizing the Dongle. The driver for the Dongle is included in the installer for the Intelligent Config PC App. You can obtain the Intelligent Config PC App by contacting your distributor. Product Ordering Information iN-DGL - iNavigator Bluetooth Dongle www.mccain-inc.com ® 3-section shown in Federal yellow1-section shown in Federal yellow Cabinets Controllers Signals Signs Software Specialty Overview Benefits Product Description McCain’s Traffic Signal Housings, available in eight and twelve inch varieties, provide a durable and low-maintenance housing for standard LED modules as well as McCain incandescent optical assemblies. Manufactured from polycarbonate or aluminum, the housings are compliant with multiple agency standards including the Institute of Transportation Engineers (ITE), Caltrans, and most state Departments of Transportation (DOTs). An industry leader in signal manufacturing and supply, McCain offers an extensive range of materials, configurations, and accessories, including backplates, visors, and signal assemblies, to meet your traffic signal requirements. • Modular design promotes flexible configuration options: one to five sections, vertical, horizontal, HAWK (3-section cluster), and doghouse (5-section cluster) • Fabricated from aluminum or polycarbonate with or without10% fiberglass reinforcement • 8” or 12” diameter • Weathertight doors • Custom hardware and terminal block locations available The McCain Traffic Signal Housings are modular in design, allowing a multitude of signal housing configurations for standard LEDs as well as McCain incandescent optical assemblies. Available in polycarbonate and aluminum, each section is injection molded or cast in one piece. Reinforcement ribs and serrated ports, both top and bottom, provide strength and positive locking with other sections and mounting hardware. Positive latching of doors is achieved with stainless steel eyebolts and wing nut assemblies, and the doors feature four metal threaded inserts for visor attachment. A positive seal is assured with an E.P.D.M. rubber gasket creating a moisture-free and dust-tight atmosphere. Traffic Signal Housings are compatible with McCain backplates and visors, available in both aluminum and ABS. The top and bottom ports allow installation into many framework mounting assemblies. Traffic Signal Housing 8” Diameter 12” Diameter Aluminum Polycarbonate There are no 8" diameter lights for this signal. © 2016 McCain Inc. Updated 12/19/16. McCain reserves the right to change product specifications without notice. For the most up-to-date information, please contact McCain. To learn more about McCain’s Integrated Traffic Solutions, please contact info@mccain-inc.com or call (760) 727-8100 2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM® Front Top Side 3-Section Dimensions are approximate and may vary. 3-section 12” housing shown as an example configuration. 3-section 8” housing height dimensions is listed in parentheses. Depth for the 8” and 12” housings are approximately the same. Minor differences between the 8” and 12” may not be shown. 8” housing12” housing Typical configurations Vertical Horizontal Doghouse Mixed SizesHAWK Standard Features • Modular sections, one-piece, injection molded or cast • 72-tooth serrated boss and reinforcing ribs, top and bottom • Brass threaded inserts for visor attachment (4) • Housings have a cast boss for mounting a 5 or 6-position terminal block; one side of terminal block with fast-on terminals, the other side with screw terminals • The words red, amber, and green are cast next to each boss to identify light source lead wires • 5 or 6-position terminal block installed in center section (1) (alternate mounting is available) • Stainless steel door roll pins and eye bolt/wing nut assemblies • Integral lugs on the housing and doors with stainless steel roll pins provide effective door hinges • Weathertight E.P.D.M. rubber door gasket • Aluminum and polycarbonate, and 8” and 12” housings can be mixed in one signal head General Specifications Dimensions: (1-section) 8”: 10.0” H x 10.0” W x 7.0” D 12”: 13.5” H x 13.5” W x 7.0” D Material: Polycarbonate: Ultraviolet and heat stabilized, flame retardant, permanently colored, 10% fiber- glass reinforcement Aluminum: Type 360, reduced corrosion, increased powder coat adhesion Finish(es): Polycarbonate: Colored resins integral to housing Aluminum: Powder coated Color(s): Federal yellow, signal green, black, or custom colors Mounting: 2.0” hole top and bottom fits 1.5” NPT fittings Environmental: Operating temperature: -37 o C to +74o C Humidity: 0 to 95% (non-condensing) Shipping Weight: (empty, 1-section) Polycarbonate: 8” - 2.1 lbs 12” - 4.2 lbs Aluminum: 8” - 4.0 lbs 12” - 7.8 lbs Options • Fiberglass-free polycarbonate • Location, quantity, and type of terminal blocks • Door mounting hardware: Push pin (removable) or roll pin (permanent) • Visors • Backplates • Mounting: Various framework, orientation, and configurations • Light Source: LED or incandescent • High-performance (highly directional) signal version Traffic Signal Housing www.mccain-inc.com ® Standard backplate, 5 inch, louvered Standard backplate, 8 inch, non-louvered High performance 3-section backplate, 5 inch, louvered Hh f Standard backplate Cabinets Controllers Signals Signs Software Specialty Overview Benefits Product Description McCain’s Backplates provide a visual contrast between signal heads and the environment enhancing signal visibility. Available for standard and programmable signal heads in eight and twelve inch sizes, backplates can be configured for one to five section, HAWK (3-section cluster), doghouse (5-section cluster), or combination signals. Available in a variety of standard and custom colors to match the signal head, backplates provide an aesthetically pleasing and functional look for your intersection. • Enhances signal visibility by creating an environmental contrast • Compatible with standard and programmable signal heads • Available in a multitude of configurations • 5” or 8” borders • Standard and custom color options The McCain Backplate collection is ideal for use in conjunction with standard or programmable signal heads. Backplates are available in several types including aluminum, ABS sheet, and vacuum-formed ABS, and the aluminum is available in a louvered style. Vacuum-formed backplates incorporate a 1/2” lip for added strength. All backplates are available with five or eight inch borders. Mounting methods vary depending on the backplate type. Every backplate has a flat black front face for increased visual contrast against the background. The back face is available in a variety of colors to match your current signal housing. Backplates Standard Signal Heads Programmable Signal Heads © 2016 McCain Inc. Updated 12/19/16. McCain reserves the right to change product specifications without notice. For the most up-to-date information, please contact McCain. To learn more about McCain’s Integrated Traffic Solutions, please contact info@mccain-inc.com or call (760) 727-8100 2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM® Standard 12” Signal Standard 8” Signal 8 Inch Width 8 Inch Width 5 Inch Width 5 Inch Width High Performance 12” Signal Example of Reflective Tape (with louvers) Typical 3-section backplates shown as examples Louvered types approximately the same size as non-louvered Dimensions rounded to the nearest 0.1” Standard Features • Accommodates 8”, 12”, cluster, and combination signal heads • 5” or 8” borders (HP available only in 5”) • Aluminum available with or without louvers; ABS, non-louvered only • Aluminum, ABS, and ABS vacuum formed (high performance signal head backplates are only available in aluminum) • ABS vacuum formed have flanged edges for added strength General Specifications Dimensions: Varies based on signal configuration Material: Aluminum, ABS Finish(es): Aluminum: Powder coat ABS: Integrally molded Color(s): Face: Flat black Back: Federal yellow, signal green, black, or custom colors Construction & Attachment: Depends on style Signal Mounting: Elevator Plumbizer (MAS) and standard Shipping Weight: Varies based on signal configuration Options • Modification to allow use of reflective tape on aluminum louvered and non louvered styles • Aluminum available with flanged edges for added stiffening Backplates www.mccain-inc.com ® Cabinets Controllers Signals Signs Software Specialty Overview Benefits Product Description McCain’s backplates provide visual contrast between signal heads and enhance signal visibility for the driver. The retroreflective borders provide an aesthetically pleasing and functional look in addition to increased traffic safety for your intersections. The Federal Highway Administration approved the use of retroreflective tape after a seven-year safety study showed that the use of retroreflective backplate borders reduced total crashes at intersections by 15% to 24%. • Enhance signal visibility • Boost driver awareness • Use on most standard signals • Command attention with 1”, 2”, or 3” retroreflective tape border McCain’s backplates with retroreflective borders for standard traffic signals fit both 8” and12” signal heads, are fabricated from aluminum or polycarbonate, and havefive-inch borders. They accommodate retroreflective tape widths of one, two, or three inches around the backplate. McCain backplates are configured for one-section to five- section in-line or five-section cluster signals. All in-line backplates are fabricated from one solid piece of aluminum or polycarbonate. The five-section cluster backplate is a three- piece design. The retroreflective tape is specially designed by 3M for vertical mounting and comes in two options: 1) 3M 3930 Series High Intensity Prismatic Reflective Sheeting 2) 3M 3990 Series Diamond Grade VIP Reflective Sheeting Backplates with Retroreflective Borders 3-Section Louvered Version © 2015 McCain Inc. Updated 04/30/15. McCain reserves the right to change product specifications without notice. For the most up-to-date information, please contact McCain. To learn more about McCain’s Integrated Traffic Solutions, please contact info@mccain-inc.com or call (760) 727-8100 2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM® Dimensions rounded to the nearest 0.1”. Dimensions shown for 3-section backplate (except height) are typical of all bacplates shown for 2” width tape. 1-Section 2-Section 3-Section 4-Section 5-Section In-Line 5-Section Cluster Standard Features • 1”, 2” or 3” reflective tape border • Available in 1-section thru 5-section in-line, and 5-section cluster configurations • Fits 8” and 12” signals • 5” overall width • Standard flat black General Specifications Dimensions: Varies based on signal configuration Material: Aluminum: 0.050” thick, louvered or non-louvered Polycarbonate: 0.10” thick, non-louvered Finish(es): Aluminum: Powder coated Polycarbonate: Colored resin integral to housing Color(s): Face: Flat black Construction & Attachment: Depends on style Signal Mounting: Elevator Plumbizer (MAS) and standard Shipping Weight: Varies based on signal configuration Retroreflective Tape Specifications Type: Prismatic, Series 3930 or 3990 Color: Yellow (standard), white (optional) Width: 1”, 2”, or 3” Manufacturer: 3M Backplates with Retroreflective Borders CAD of Examples of Backplates with 2” Tape Close-up of Reflective Tape (aluminum louvered backplate) www.mccain-inc.com ® Tunnel Full Circle Cap Scoop 45° Angle Cabinets Controllers Signals Signs Software Specialty Overview Benefits Product Description McCain’s Signal Visors increase signal visibility in sunlight while still allowing an unobstructed view for multiple lanes of approaching drivers and pedestrians. McCain produces a range of standard and angled visors including tunnel, full circle, and cap, that offer a variety of signal viewing angles. Whether you are looking for aluminum or polycarbonate, Federal yellow, signal green, black, or custom colors, McCain has the visors to meet your needs. Increases signal visibility in sunlightt Available in a variety of materials, sizes, styles, and t angles to meet your specific requirements Twist-on tabs facilitate ease of installationt One-piece construction (except Scoop Visor)t McCain’s Signal Visors, molded polycarbonate or stamped and formed aluminum, are available in eight inch and 12 inch signal configurations. Integrally formed, twist-on mounting tabs make installation and maintenance a snap, and a standard three degree downward tilt facilitates signal visibility. Specialty visors include the 45° Angle Visor and the Scoop Visor. The 45° Angle Visor comes in two standard lengths, 18” and 27” and in right and left versions. It is designed to narrow visibility for locations such as an angled intersection. The Scoop Visor is designed to resist snow build-up on signal lenses in colder climates. A louvered vent on top and an open bottom contribute to the increased vertical movement of air across the face of the signal lens thereby increasing resistance to the deposit of snow. Signal Visors Aluminum Polycarbonate 45° Angle Cap Full Circle Scoop Tunnel © 2009 McCain Inc. Updated 03/05/09. McCain reserves the right to change product specifications without notice. For the most up-to-date information, please contact McCain. To learn more about McCain’s Integrated Traffic Solutions, please contact info@mccain-inc.com or call (760) 727-8100 2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM® Front Cap Tunnel Full Circle Scoop 45° (18” right angle version) Side Top Dimensions rounded to the nearest 0.1” All visors shown are 12” signal versions Dimensions shown in Cap front view and degree of tilt shown in side view are typical of all 12” visors Standard Features One-piece construction (except Scoop)t Twist-on mounting tabst 3° downward tiltt General Specifications Dimensions: Standard Visors: Diameter Depth 8” 8” 12” 12” 45° Angle Visors: 8” 18” 12” 18” 12” 27” Degree of Tilt: 3° (down) Material: Aluminum: Type 3003, very good corrosion resis- tance, 0.050” thick Polycarbonate (standard visors only): Ultraviolet and heat stabilized, flame retardant, permanently colored, 0.10” nominal thickness Finish(es): Aluminum: Powder coated Polycarbonate (standard visors only): Colored resins integral to visor Color(s): Exterior: Federal yellow, signal green, black, or custom Interior: Flat black Mounting: Twist-on tabs Shipping Weight: 1 - 4 lbs., varies based on material, size, and style Options Other lengths availablet Degree of tiltt Signal Visors www.mccain-inc.com ® © 2010 McCain Inc. Updated 10/12/10. McCain reserves the right to change product specifi cations without notice. For the most up-to-date information, please contact McCain. 2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM Cabinets Controllers Signals Signs Software Specialty Vehicle Signal Mount Mast Arm MAS Off set Green Bronze Description This Vehicle Signal Mount is installed between two signal sections, typically the red and yellow sections. Attaches vehicle signal to tenon on the traffi c signal pole mast arm. Serrations on the arm matches signal housing serrations to lock signal in place. Three set screws on the outer ring provide fi rm attachment to the mast arm. A safety bolt provides additional security. Also includes three threaded screw holes on the inner ring for additional set screws (optional). Fabricated from bronze alloy and powder coated green. Includes set screws (3), safety bolt, jamb nuts, and washers. Meets Caltrans requirements for MAS, and ADOT requirements for Type II. Part Number M18284 YELLOW The Greatest Signals Stand the Test of Time.TM VLA Model LED Signal Modules 8 and 12 inch Incandescent look (120V) GE Lighting Solutions Robust Features ß1XGTOQNFGFGNGEVTKECNEQPPGEVQTURTGXGPVYCVGT  YKEMKPIVJTQWIJYKTGU ß1RVKOCNVJGTOCNOCPCIGOGPVHQTNQPIGTNKHG ß2TQXKFGURGTHQTOCPEGWPFGTGZVTGOGõGNF  VGORGTCVWTGEQPFKVKQPU Innovative Design ß.QYRTQõNGOQFWNGRGTOKVUGHõEKGPVKPUVCNNCVKQPKPVQ  GZKUVKPIVTCHõEJQWUKPIU ß2QYGTEQPUWORVKQPNGXGNUCNNQYEQORCVKDKNKV[  YKVJOQUVEQPVTQNNGTU ß/CUMEQORCVKDNGVQõV[QWTWPKSWGUKIPCNKPIPGGFU Outstanding Performance ß*KIJDTKIJVPGUUEGPVTCNNKIJVUQWTEGCPFEWUVQOQRVKECN  NGPUKPIFKUVTKDWVGNKIJVWPKHQTON[CPFGHõEKGPVN[ ß4KIQTQWUN[VGUVGFHQTNQPINKHGFGUKIP  CPFNQYOCKPVGPCPEGEQUVU ß'ZEGNNGPVEQNQTWPKHQTOKV[ Meets Rigorous Certification & Testing Standards ß+PVGTVGM'6.8GTKõGFEQORNKCPV ß%QORNKCPVYKVJ+6'86%5*.'&%KTEWNCT5KIPCN5WRRNGOGPV  FCVGF,WPG VJ ß%5#CRRTQXGF  5QNFUGRCTCVGN[4GHGTVQOCUMUFCVCUJGGV64#( VLA Model LED Signal Modules ~'P]S !X]RW Mechanical Outline Dimensions in inches [mm] 64;XVWcX]VB^[dcX^]b~1-888-MY-GE-LED~fffVT[XVWcX]Vb^[dcX^]bR^\ 1 - 8 8 8 - 6 9 - 4 3 - 5 3 3 GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. The GE brand and logo are trademarks of the General Electric Company. © 2012 GE Lighting Solutions, LLC. 8]U^a\PcX^]_a^eXSTSXbbdQYTRcc^RWP]VTfXcW^dc]^cXRT0[[eP[dTbPaTSTbXV]^ach_XRP[eP[dTbfWT]\TPbdaTSd]STa[PQ^aPc^ahR^]SXcX^]b CA05! &A&! ! Front View Side View 275 10.8 297 11.69 64 2.5 264 10.4 77 3 Back View 8 inch 12 inch 61 2.4 51 2.01 174 6.9 208 8.2 186 7.3 Front View Back ViewSide View Operating Specifications Parameter Rating Operating Temperature Range* -40 to +74°C (-40 to +165°F) Operating Voltage Range 80 to 135 V (60Hz AC) Power Factor (PF) > 90% Total Harmonic Distortion (THD) < 20% Minimum Voltage Turn-Off (VTO) 35 V Turn-On / Turn-Off Time < 50 ms Lens & Shell Material UV Stabilized Polycarbonate Wiring 40 in, 18 AWG, Color Coded with Strain Relief * Operating Temperature Range per ITE 2005, Section 3.3.2 Design Compliance Test type Compliance ITE VTCSH- Luminous Intensity LED Circular Signal Supplement -June 2005 Chromaticity ITE VTCSH- LED Circular -June 2005 Moisture Resistance Blown Wind Rain MIL-STD-810F method 506.4 Mechanical Vibration MIL-STD-883 Method 2007 Electronic Noise FCC Title 47 Sub. B Sec 151 Sec. 2.1.6 NEMA TS2-2003, 300V, 2500W Transient Voltage Protection Sec. 2 .1.6 NEMA TS2-2003, 600V, 10μF Sec. 2.1.8 NEMA TS2-2003, 1kV, 2Ω Controller Compatibility ITE VTCSH- LED Circular Signal Supplement -June 2005 Wiring NFPA 70, National Electric Code Sec. 8.2 IEC 61000-4-5 & Sec. 6.1.2 ANSI/IEEE Transient C62.41.2 - 2002, 3KV, 2 Ω Suppression Sec. 8.0 IEC 61000-4-12 & Sec. 6.1.1 ANSI/IEEE C62.41.2 - 2002, 6KV, 30 Ω Distributed by: Standard product equipped with universal connectors (insulated spade-quick disconnect). All lamps available in tinted or clear lens. 1 Class A 2 Measured at vertical angle of -2.5° and at horizontal angle of 0°. Product Information Wavelength Maintained Model Number Front Shell Size AC Voltage Power (W) (nm) Intensity (Cd) (in) Nominal Nominal nominal Minimum2~ DR4-RTFB-VLA Tinted 8 120V - 60Hz 6.4 628 240 ~ DR4-YTFB-VLA Tinted 8 120V - 60Hz 9.9 589 760 DR4-YCFB-VLA Clear 8 120V - 60Hz 9.9 589 760~ DR4-GTFB-VLA Tinted 8 120V - 60Hz 6.4 499 450 DR4-GCFB-VLA Clear 8 120V - 60Hz 6.4 499 450~ DR6-RTFB-VLA Tinted 12 120V – 60Hz 10.2 626 365 DR6-RCFB-VLA Clear~ DR6-YTFB-VLA Tinted 12 120V – 60Hz 12.6 589 910 DR6-YCFB-VLA Clear~ DR6-GTFB-VLA Tinted 12 120V – 60Hz 10.6 502 475 DR6-GCFB-VLA Clear Bi-Modal Arrow LED Traffic Signal Modules 12 inch, Green and yellow Features and Benefits ß*KIJGHHKEKGPE[CPFNQPINKHG.'&NKIJVUQWTEG ß/QKUVWTGCPFFWUVTGUKUVCPV ß&GUKIPGFHQTPGYQTTGVTQHKVWUG ß#NNRTQFWEVUUJKRRGFYKVJICUMGVKPUVCNNGF ß2TQXKFGURGTHQTOCPEGWPFGTGZVTGOGHKGNF  VGORGTCVWTGEQPFKVKQPU 4.74" (121) 3.37" (86) 6.45" (164) 11.83" (300) 11.15" (291) Mechanical Outline Dimensions in (mm) Design Compliance Test Type Compliance Chromaticity ITE VTCSH-LED Vehicle Arrow Traffic Signal Supplement, July 2007 Moisture Resistance NEMA STD 250-1991 Mechanical Vibration MIL-STD-833 Method 2007 Electronic Noise FCC Title 47 Sub. B Sec. 15 1 Wiring NFPA 70, National Electric Code Operating Specifications Parameter Rating Operating Temperature Range -40 to +74°C (-40 to +165°F) Operating Voltage Range 80 to 135 V (60Hz AC) Power Factor (P.F.) > 90% Lens & Shell Material UV Stabilized Polycarbonate Total Harmonic Distortion (T.H.D.) < 20% Wiring 16 AWG, Color Coded with Strain Relief Product Information Model Number Dimensions AC Voltage Power (W) Color Profile (in) Nominal Nominal Type DR6-ECA6-01A 12 120V - 60Hz 10/10 Bi-Modal Green Arrow & Yellow 1 Class A. GE Lighting Solutions 64;XVWcX]VB^[dcX^]b~1-888-MY-GE-LED~fffVT[XVWcX]Vb^[dcX^]bR^\ 1 - 8 8 8 - 6 9 - 4 3 - 5 3 3 GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. The GE brand and logo are trademarks of the General Electric Company. © 2012 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions. TRAF232-R020712 www.mccain-inc.com ® shown in Federal yellow shown in black 16 inch housing 12 inch housing shown in black 12 inch housing Cabinets Controllers Signals Signs Software Specialty Overview Benefits Product Description McCain’s Pedestrian Signal Housings are designed to be used in conjunction with standard or LED pedestrian signal modules to promote pedestrian safety at intersections. McCain housings exceed the Institute of Transportation Engineers (ITE) standards, offering a low maintenance and durable housing in either die cast aluminum or injection molded polycarbonate resin. They are available in 12” or 16” styles, and the 12” housings are available in 1-section or 2-section varieties. The 12” polycarbonate housings are reinforced with a 10 percent fiberglass fill for superior strength and durability unmatched by standard polycarbonate resins. The fiberglass fill is optional on the 16” polycarbonate housings. 12” or 16” stylest Rugged aluminum or polycarbonate constructiont Designed for standard symbol or word pedestrian t signal modules including LED Door-hinge hardware can be removable and t reversible or permanently attached Highly customizable including a variety of t fabrication, mounting, and visor options 16” available with tVantage Visor™ for increased visibility and impact protection The McCain Pedestrian Signal Housing is available in 12” and 16” styles and a variety of configurations including aluminum or polycarbonate construction, with a number of options (see Options for details). The door is attached with stainless steel detent-type clevis or roll pins and eye bolt/wing nut assemblies. Two equally spaced mounting lugs, integrally cast into the top and bottom of the 16” and the sides of the 12”, allow the doors to hinge from either direction. When clevis pins are used, the door and eye bolt assemblies can be removed and rotated without the use of any tools, facilitating maintenance. All interior mounting locations on the 16” housing are symmetrically positioned, allowing the rotation of components when using the bi-directional McCain Clamshell Mount to mount to the right or left side. Pedestrian Signal Housing 12” Housing 16” Housing Aluminum Polycarbonate © 2009 McCain Inc. Updated 02/12/09. McCain reserves the right to change product specifications without notice. For the most up-to-date information, please contact McCain. To learn more about McCain’s Integrated Traffic Solutions, please contact info@mccain-inc.com or call (760) 727-8100 2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM® Top Side Front Dimensions rounded to the nearest 0.1” 12” housing 16” housing 16” Clamshell mount (sold separately) 16” Tunnel visor (sold separately) 16” Vantage Visor (sold separately) 16” with Vantage Visor12” 2-section with tunnel visors Hand/Man modules (sold separately) Standard Features Stainless steel hardware includes hinge pins (detent-type clevis or t roll) and eye bolt/wing nuts (latch) Terminal block with quick-disconnect fittings on one side of each t terminal position and screw clamps on the other side General Specifications Dimensions*: 12” Housing 16” Housing Housing:13.2” H x 13.2” W x 5.7” D 15.8” H x 17.4” W x 7.3” D Door (incl. tabs): 13.5” H x 15.0” W x 5.6” D 18.7” H x 18.5” W x 1.8” D Overall:14.0” H x 15.0” W x 11.3” D 18.7” H x 18.5” W x 9.1” D Material: Polycarbonate: Ultraviolet and heat stabilized, flame retardant, permanently colored, 10% fiberglass rein- forcement (12” standard, 16” optional) Aluminum: Type 360, reduced corrosion, increased powder coat adhesion Finish(es): Polycarbonate: Colored resins integral to housing Aluminum: Powder coated Color(s): Federal yellow, signal green, black, or custom colors Access: Front door (1), 16”: hinged top or bottom 12”: hinged left or right Latching System: Eye bolt assemblies Mounting: Standard signal hardware Environmental: Operating temperature: -37 o C to +74o C Humidity: 0 to 95% (non-condensing) Shipping Weight: 12”: Poly 5 lbs, Al 9 lbs 16”: Poly 9 lbs, Al 10 lbs Options Polycarbonate 10% fiberglass fill for added durability (optional on t 16”, standard on 12”) Modules: LED or incandescent; international Hand/Man symbol, t “WALK”/”DON’T WALK” words Visors: tVantage Visor (16” only), tunnel, or cap (12” only) Clamshell mount (16” only - housing available pre-drilled for mount)t Custom terminal blockst Door hardware permanent (roll pins) or removable (clevis pins)t Pedestrian Signal Housing * Dimensions are approximate and vary based on material used www.mccain-inc.com ® Shown Mounted on 16” Pedestrian Housing in Federal Yellow Cabinets Controllers Signals Signs Software Specialty Overview Benefits Product Description McCain’s Clamshell Mount is a quick and convenient way to mount a 16-inch pedestrian housing. Installed half on the pole and half on the housing, the dual-mount pieces easily slide together creating a singular, secure mount. When the pedestrian housing requires maintenance or needs to be replaced, the mount easily separates, allowing the housing to be quickly taken down and remounted in the field. Multiple mounting options to accommodate your t specific requirements Quick and easy to installt Can be left or right mounted or easily converted one t to the other Vandal-resistantt Available in multiple colorst The McCain Clamshell Mount is a two-piece 16-inch pedestrian housing mount. Its unique design allows multiple mounting methods to poles four inches in diameter and larger, including through-bolt, banding, and lag screw. When using through-bolts, horizontally elongated bolt holes allow the mount to be rotated on the pole for ideal positioning. The signal half of the Clamshell Mount is bolted directly onto the pedestrian housing and is secured to the pole-mount piece with stainless steel hinge pins. McCain’s pedestrian housing can be ordered pre-drilled to readily accept the clamshell bolts making installation a snap! Completing the installation, the two halves are secured to each other via a vandal-resistant flathead socket bolt. The mount is made from cast aluminum alloy for strength and longevity and is available in a variety of colors to appear as though a continuation of the pedestrian housing. Clamshell Mount © 2009 McCain Inc. Updated 02/12/09. McCain reserves the right to change product specifications without notice. For the most up-to-date information, please contact McCain. To learn more about McCain’s Integrated Traffic Solutions, please contact info@mccain-inc.com or call (760) 727-8100 2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM® Interior view Front Top Side Dimensions rounded to the nearest 0.1” Standard Features 2-part mounting assemblyt Symmetrical mounting holes allow for left or right mountt Neoprene gasket provides a weathertight sealt 3-position, 2-row terminal block mounted in the upper half of the t signal mounted portion; one side with fast-on terminals, the other side with screw terminals 28” wire leads (3) provided to wire clamshell terminal block to t pedestrian signal terminal block Field wiring is terminated on clamshell terminal blockt Flathead 3/16” hex socket closure boltt General Specifications Dimensions: 11.1” H x 5.1” W x 2.4” D Material: Cast aluminum alloy Finish(es): Powder coated Color(s): Federal yellow, signal green, black or custom colors Latching System: Flathead 3/16” hex socket bolt Mounting: Band, through-bolt, or lag screw Shipping Weight: 4.5 lbs Options Conduit entrance for wood pole mountt Pedestrian housings can be ordered pre-drilled for easy clamshell t attachment Clamshell Mount LED Countdown Pedestrian Signals 16 x 18 inch Excellent Appearance & Visibility • Robust LED system design enables high luminous intensity over product life cycle • Efficient optical system minimizes power consumption while providing excellent uniformity and viewing angles • Single piece transparent front window with internal masking to prevent: - countdown and icons display from being readily visible when not in operation - scratches and abrasions compared with external silk screen technology • Bright and clear icons • Fully uniform look • Lower profile* • Improved luminous intensity uniformity Outstanding Reliability & Robust Operation • Internal conflict monitor preventing walk and don’t walk indications to light up at the same time • Individual power supply drives each display to ensure proper indication • Reduced overall power consumption* * Compared to PS7-CFF1-27A Meets Rigorous Certification & Testing Standards • Intertek ETL Verified compliant • DOE compliant • Using MIL-STD-810F and NEMA 250-1991 Type 4 for environmental robustness, passed reliability and qualification testing including high temperature, high humidity cycling (HTHH for 1,000 hours) • Compliant (for Full Hand/Full Person) with the ITE PTCSI LED Signal Modules - version dated August 2010 The Greatest Signals Stand the Test of Time.TM GE Lighting LED Countdown Pedestrian Signals • 16 x 18 inch module Mechanical Outline Dimensions in inches. (mm) indicates metric equivalent 17.7" (449) 16.0" (406) 13.9" (354) 17.7" (449) 16.0" (406) Operating Specifications Parameter Rating Operating Temperature Range* -40 to +74°C (-40 to +165°F) Operating Voltage Range 80 to 135 V (60Hz AC) Power Factor (PF) > 90 % Total Harmonic Distortion (THD) < 20 % Voltage Turn-Off (VTO) 35 V Start-up Time < 75msec Lens & Shell Material UV Stabilized Polycarbonate Wiring 16 AWG, Color Coded with Strain Relief LED Color Hand: Portland Orange Person: Lunar White Countdown: Portland Orange Default Mode Hand only * Performed in compliance with ITE test method described in the technical notes Design Compliance Test type Compliance Luminous intensity, ITE PTCSI LED Signal Modules Uniformity & Viewing Angles version of August 2010 Chromaticity ITE PTCSI LED Signal Modules version of August 2010 MIL-STD-810F Moisture Resistance Procedure 1, Rain & Blowing Rain Mechanical Vibration MIL-STD-883 Test Method 2007 Electronic Noise FCC Title 47 Sec 15 Sub. B1 Sec. 2.1.6 NEMA TS 2-2003 Transient Voltage Protection Sec. 2.1.8 NEMA TS 2-2003 Controller Compatibility NEMA TS-2-2003 Sec. 8.2 IEC 1000-4-5 & Sec. 6.1.2 ANSI/IEEE Transient C62.41.2 - 2002, 3KV, 2 Ω Suppression Sec. 8.0 IEC 1000-4-12 & Sec. 6.1.1 ANSI/IEEE C62.41.2 - 2002, 6KV, 30 Ω Wiring NFPA 70, National Electric Code Digits MUTCD 2003, Section 4E.07, Countdown Numbers Minimum 9’’ Height & 7’’ Width 1 Class A Product Information Minimum Luminous Dimensions Symbol AC Voltage Power (W) Intensity Cd/m2 Model Number Dimensions Layout Hand Person Nominal Hand Person Countdown Hand/Digit Person PS7-CFF1-VLA 16 x 18 in Overlay Full Full 120V - 60Hz 6 6 8 1400 2200 Countdown 1 Class A. 2 Full MUTCD Compliance Test Condition : Ta = 25˚C. All values are design or typical values when measured under laboratory conditions. GE Lighting • 1-888-MY-GE-LED • www.gelighting.com 1 - 8 8 8 - 6 9 - 4 3 - 5 3 3 for North America · or · +1.216.266.2419 GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. “The Greatest Signals Stand the Test of Time” are trademarks of GE Lighting, LLC. The GE brand and logo are trademarks of the General Electric Company. © 2014 GE Lighting, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions. TRAF289-R012615 www.mccain-inc.com ® © 2009 McCain Inc. Updated 07/02/09. McCain reserves the right to change product specifi cations without notice. For the most up-to-date information, please contact McCain. 2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM Cabinets Controllers Signals Signs Software Specialty Signal Mount Pole Top 1-Way Bronze Green Caltrans TP-1 and TV-1 Description This Signal Mount attaches a pedestrian or vehicle signal to the top of a 4” to 4½” diam- eter signal pole. The single port on the top of this mount is serrated and off set. Fabri- cated from bronze alloy. Powder coated green. Includes two rows of three set screws to secure the mount to the top of the pole. Also included are a lock nut and aluminum washer. Meets Caltrans specifi cations for a TP-1 and TV-1. Part Number M18511 YELLOW Description The Opticom™700 Series Detectors transform the optical energy detected from an approaching, vehicle-mounted Opticom™ Emitter to an electrical signal. The electrical signal is transmitted along a cable to the Opticom™Phase Selector or Opticom™ Discriminator for processing. Opticom 700 series detectors are mounted at or near the intersection that permits a direct, unobstructed line-of-sight to vehicle approaches. Opticom detectors may be mounted on span wire, mast arm or other appropriate structures. Opticom™Models 711, 721 and 722 Detectors offer significant advances and flexibility for specific intersection applications. The Opticom detectors are designed for common applications in three configurations: one direction—the single channel Opticom model 711; the single channel, dual detection Opticom model 721; and two direction, two output detection—the dual channel Opticom model 722. All Opticom 700 series detectors greatly reduce installation and life cycle costs through their modular design, adjustable tubes, and compatibility with existing Opticom™Infrared System intersection and vehicle equipment. Features • Advanced electrical transient immunity • Modular design • Adjustable turret configuration: accommodates skewed approaches • Lightweight, durable, high-impact polycarbonate enclosure • Simplified installation: span wire or mast arm • Gray door identification of Opticom model 722 Opticom™Models 722, 721 (back) and 711 Detectors October 2007 Opticom™Infrared System Opticom™Models 711, 721 and 722 Detectors Opticom™Infrared System Matched Component Products Accessories • Opticom™Span Wire Clamp • Opticom™Model 138 Detector Cable Operating Parameters • Reception Range:200 ft. (60 m) adjustable up to 2,500 ft. (760 m) • Electrical:24 to 28 VDC, 50 MA minimum • Temperature Range:-30º F (-34º C) to 165º F (74º C) • Humidity:5% to 95% relative Physical Dimensions Opticom™Model 711 Detector Length: 12.0 in. (30.5 cm) Width: 4.75 in. (12.1 cm) Height: 5.63 in. (14.3 cm) Weight: 0.88 lbs. (400 g) Opticom™Models 721 and 722 Detectors Length: 12.0 in. (30.5 cm) Width: 4.75 in. (12.1 cm) Height: 7.13 in. (18.1 cm) Weight: 1.12 Ibs. (508 g) Opticom™Span Wire Clamp Opticom ™Model 138 Detector Cable Global Traffic Technologies Canada, Inc. 157 Adelaide Street WestSuite 448Toronto, ON M5H 4E7Canada1-800-258-4610 Opticom is a trademark of Global TrafficTechnologies, LLC. Used under license in Canada. Please recycle. Printed in U.S.A. © Global Traffic Technologies, LLC 2007 All rights reserved. 75-0500-1682-5 (A) Global Traffic Technologies, LLC7800 Third Street North St. Paul, Minnesota 55128-54411-800-258-4610 651-789-7333www.gtt.com Important Notice to Purchaser:EXCEPT FOR THE LIMITED WARRANTIES SET FORTH IN THIS DOCUMENT, GLOBAL TRAFFIC TECHNOLOGIES (GTT) MAKESNO OTHER WARRANTIES AND EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED,INCLUDING, WITHOUT LIMITATION, ANY WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. GTT will, at its sole option, repair, replace or refund any amounts paid for any Opticom™ Infrared System component found tobe defective in materials or manufacture within five (5) years from the date of shipment from GTT. See “Warranty and ExtendedCoverage” for details and limitations of the coverage plan. GTT will provide a functioning replacement component at a standardcharge per unit for an additional five (5) years. GTT warrants future system operability coverage as described herein. The warranties set forth in this document shall not applyto (A) incandescent lamps (confirmation lights) or (B) any Opticom infrared system components which have been (1) repaired ormodified by persons not authorized by GTT; (2) subjected to incorrect installation, misuse, neglect or accident; (3) damaged byextreme atmospheric or weather-related conditions; or (4) subjected to events or use outside the normal or anticipated course. IN NO EVENT SHALL GTT BE LIABLE FOR ANY INJURY (INCLUDING, WITHOUT LIMITATION, PERSONAL INJURY), DEATH,LOSS, OR DAMAGE (INCLUDING, WITHOUT LIMITATION, PROPERTY DAMAGE), WHETHER DIRECT, INDIRECT, INCIDENTAL,SPECIAL, CONSEQUENTIAL OR OTHERWISE, ARISING OUT OF THE USE OR INABILITY TO USE, REPAIR OR FAILURE TO REPAIR, ANY GTT PRODUCT, REGARDLESS OF THE LEGAL THEORY ASSERTED. THE REMEDIES SET FORTH IN THIS DOCUMENT ARE EXCLUSIVE. Sale and use of the Opticom infrared system is expressly restricted to authorized agencies of government customers, withintheir specific jurisdictions. However, because the infrared signal generated by the Opticom infrared system is not exclusive, GTT does not warrant exclusive activation by purchaser. Authorized users who desire to use or coordinate use of the Opticominfrared system with that of other jurisdictions must first obtain the prior written approval of each authorized user in thejurisdiction where use is sought. Description Opticom™Model 138 Detector Cable is designed and manufactured explicitly for use with Opticom™Detectors. Opticom model 138 has three color-coded conductors, a conductive shield and drain, and a black PVC jacket. This durable, high-quality cable carries the appropriate power to the detector from the Opticom™Phase Selector and delivers the necessary quality signal to the phase selector discriminator circuitry up to 1,000 feet (305 m). Features and Benefits • Optimized to interface Opticom detectors to Opticom phase selectors or Opticom™ Discriminators • Ensures effective range of 2,500 feet (760 m) with Opticom™Infrared System components • Durable construction —Suitable for direct burial —Suitable for conduit and mast arm pull —Suitable for exposed overheadinstallation* Operating Parameters •600 volt rating • 75° C (167° F) temperature range •Three-conductor AWG #20 (7x28) stranded, individually tinned copper: yellow, blue and orange • Aluminized polyester shield with 20% overlap •Drain AWG #20 (7x28) stranded, individually tinned copper • Controlled electrical characteristics Physical Dimensions •Outside diameter:0.3 in. (7.62 mm) •Weight: 0.04 lbs./ft. (65.5 g/m) •Available in: 500 ft., 1,000 ft., 2,500 ft. and 5,000 ft. (152 m, 305 m, 760 m and 15,200 m) spools Opticom™Model 138 Detector Cable is 0.3 in. (7.62 mm) in diameter and is suitable for direct burial as well as in conduit and exposed overhead installation.* October 2007 Opticom™Infrared System Opticom™Model 138 Detector Cable An Opticom™Infrared System Matched Component Product *Separate messenger wire required Global Traffic Technologies Canada, Inc. 157 Adelaide Street WestSuite 448Toronto, ON M5H 4E7Canada1-800-258-4610 Opticom is a trademark of Global TrafficTechnologies, LLC. Used under license in Canada. Please recycle. Printed in U.S.A. ©Global Traffic Technologies, LLC 2007 All rights reserved. 75-0500-4553-5 (A) Global Traffic Technologies, LLC7800 Third Street NorthSt. Paul, Minnesota 55128-54411-800-258-4610651-789-7333www.gtt.com Important Notice to Purchaser: EXCEPT FOR THE LIMITED WARRANTIES SET FORTH IN THIS DOCUMENT, GLOBAL TRAFFIC TECHNOLOGIES (GTT) MAKES NO OTHER WARRANTIES AND EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. GTT will, at its sole option, repair, replace or refund any amounts paid for any Opticom™ Infrared System component found to be defective in materials or manufacture within five (5) years from the date of shipment from GTT. See “Warranty and Extended Coverage” for details and limitations of the coverage plan. GTT will provide a functioning replacement component at a standard charge per unit for an additional five (5) years. GTT warrants future system operability coverage as described herein. The warranties set forth in this document shall not apply to (A) incandescent lamps (confirmation lights) or (B) any Opticom infrared system components which have been (1) repaired or modified by persons not authorized by GTT; (2) subjected to incorrect installation, misuse, neglect or accident; (3) damaged by extreme atmospheric or weather-related conditions; or (4) subjected to events or use outside the normal or anticipated course. IN NO EVENT SHALL GTT BE LIABLE FOR ANY INJURY (INCLUDING, WITHOUT LIMITATION, PERSONAL INJURY), DEATH,LOSS, OR DAMAGE (INCLUDING, WITHOUT LIMITATION, PROPERTY DAMAGE), WHETHER DIRECT, INDIRECT, INCIDENTAL,SPECIAL, CONSEQUENTIAL OR OTHERWISE, ARISING OUT OF THE USE OR INABILITY TO USE, REPAIR OR FAILURE TO REPAIR, ANY GTT PRODUCT, REGARDLESS OF THE LEGAL THEORY ASSERTED. THE REMEDIES SET FORTH IN THIS DOCUMENT ARE EXCLUSIVE. Sale and use of the Opticom infrared system is expressly restricted to authorized agencies of government customers, withintheir specific jurisdictions. However, because the infrared signal generated by the Opticom infrared system is not exclusive, GTT does not warrant exclusive activation by purchaser. Authorized users who desire to use or coordinate use of the Opticominfrared system with that of other jurisdictions must first obtain the prior written approval of each authorized user in thejurisdiction where use is sought. Part #2020060001 Jet Black Ral 9005 Hammer Finish 1122 Industry Street, Bldg B Phone (425) 438-1133 Everett, WA 98203 Fax (425) 438-1585 1 March 31, 2017 Prime Electric, Inc. 13301 SE 26th St Bellevue, WA 98005 Attention: Andrew Hollenback Regarding: City of Renton GHC Longacres Materials List –SUBMITTALS Bid Item #1; Traffic Signal System - SW 27th Street @ Naches Avenue SW VIDEO DETECTION: ITEM QTY DESCRIPTION 1 4 Camera (Wide Dynamic Range) Video Zoom NTSC 115VAC (Color) 2010 Iteris Part # CAM-RZ4CA(WDR)-PAK 2 4 Astro-Brac Camera Mount 74” Tube 84” Cable Pelco Products Part # AB-0175-74-84-PNC 3 1 Cable Siamese Belden 8281 & 16/30 Power combined 1000 Foot Roll General Cable Part # SIAMESE-2/1000 Enclosed are (1) copy of submittal data sheets for the equipment on the above referenced project. Please return to Western Systems (1) submittal package with comments once approval has been granted. Any additional equipment required that changes the scope of the project will be addressed as a change order. Your order is currently not scheduled for a beginning delivery pending return of approved submittals. If a specific date is appropriate please confirm by written communication and we will do our best to meet your requirements. Sincerely, WESTERN SYSTEMS Shawna Storms Estimator 2017W1570 / WSQ WA-SS509A 2 There should only be 2 Iteris Cameras and 2 Vector Video Camera Innovation for better mobilityInnovation for better mobility The industry’s most advanced video detecƟ on camera The RZ-4 Advanced WDR (RZ-4 AWDR) is Iteris’ premium video detecƟ on camera. OpƟ mized for traffi c video detecƟ on, the RZ-4 AWDR combines Iteris’ best-in-class all-weather performance video detecƟ on with Wide Dynamic Range (WDR) technology – using the advanced imager technology to handle extremes in light and dark and severe glare condiƟ ons. In harsh backlit condiƟ ons, vehicles can be detected with >100dB of dynamic range; the camera can handle the most complicated scene. The RZ-4 AWDR’s simple installaƟ on, backward compaƟ bility, and the capability to adjust the camera from the cabinet provides an advanced, easy-to-use soluƟ on for video vehicle detecƟ on. RZ-4 A—òƒÄ‘›—™ WDR Advanced video detection enhanced with wide dynamic range technology The RZ-4 AWDR detects vehicles in any lighƟ ng and weather condiƟ ons. In contrast to other CCTV type or thermal imaging cameras, the RZ-4 AWDR delivers a video signal that is opƟ mized for processing by the Vantage video detecƟ on systems. Innovation for better mobility RZ-4 A—òƒÄ‘›—™ WDR Advanced video detection enhanced with wide dynamic range technology B›Ä›¥®ãÝ • Specifi cally designed for vehicle detecƟ on applicaƟ ons • Improved color and clarity of the video image, ideal for connecƟ on to an Vantage EdgeConnect TM • Quick-click connectors and adjustable camera mount streamline installaƟ on and minimize setup Ɵ me – no crimping tools required! • Set up and confi gure at the camera or from the ground • Cable terminaƟ on located at the rear of the camera simplifi es cable connecƟ on • Performs in the most challenging lighƟ ng condiƟ ons • Advanced heater enables opƟ mal video detecƟ on performance in adverse weather condiƟ ons. Vantage LAM The LAM (Lens Adjustment Module) is an easy to use device that allows fi eld adjustment of the camera seƫ ngs. The unit is available in NTSC or PAL format, and can be used with or without a monitor. No laptop required for set up. S֛‘®¥®‘ƒã®ÊÄÝ Imager 811 x 508 eff ecƟ ve pixels 540 TV lines minimum AutomaƟ c white balance >50 dB S/N raƟ o Dynamic range >100 dB .003 lux capable 3D-DNR Noise ReducƟ on Lens Focal length and focus adjustable at the rear of housing for a horizontal fi eld of view ranging from 2.3°tele to 58° wide 27x zoom Focus Adjustable/auto focus ConnecƟ ons Terminal block type connecƟ on Physical Dimensions 17” (43.2cm) long x 5” (12.7cm) diameter (without mounƟ ng bracket) Weight 5.7 pounds (2.6 Kg), including camera, lens, using, sunshield, and mounƟ ng bracket Environment Temperature –31° F to +165° F (–35° C to +74° C) Humidity 0% to 100% VibraƟ on 0.5G, 3 axes, 5-30 Hz Shock 10G in all 3 axes Power Standard 115/230 VAC (5W typical, 25W max.) 50/60 Hz Heater Indium Tin Oxide, proporƟ onal power Easier to install and maintain The RZ-4 AWDR camera also gives technicians the opƟ on to set up the fi eld of view (FOV) from the bucket truck or from the ground at the cabinet. ISO 9001:2008 Copyright © 2012 Iteris, Inc. All rights reserved. NOTICE: Iteris, Inc. reserves the right to change product specifi cations without notice. Information furnished is for informational purposes only. This information may not be complete or the latest revision. For the most up-to-date information, please contact Iteris, Inc. July 2012 Ver1 www.iteris.com Page T7-1www.pelcoinc.com - sales@pelcoinc.com - 405-340-3434 - fax: 405-340-343507/01/11CAMERA MTGSAstro-Brac 1-Piece Camera Bracket Stellar Series Note: 1. All assemblies are supplied standard with stainless steel fasteners. 2. 1-piece bracket for mounting Iteris, Odetics, or Econolite Solo Pro type cameras. 3. See Reference Section for available paint colors. Note: Stainless steel upgrade available: includes stainless cable. Specify by including -SS in the part number, i.e., AS-0175-23-62-SS-PNC. Camera Bracket, 1-Piece, Extended Tilt & Pan Stellar Series Cable Mount, Alum AS-0175 - - - Cable Length 62=62” Cable 84=84” Cable 96=96” Cable Coating PNC=Process No ColorP_ _=Paint Tube Length 23=23” Tube37=37” Tube 46=46” Tube 58=58” Tube 74=74” Tube Note: Stainless steel upgrade available: includes stainless clamp screw kit. Specify by including -SS in the part number, i.e., AS-0170-23-29-SS-PNC. Camera Bracket, 1-Piece, Extended Tilt & Pan Stellar Series Band Mount, Alum AS-0170 - - - Band Length 29=29” Band 36=36” Band 42=42” Band 48=48” Band 56=56” Band Coating PNC=Process No Color P_ _=Paint Tube Length 23=23” Tube 37=37” Tube 46=46” Tube 58=58” Tube 74=74” Tube Camera Bracket, 1-Piece, Extended Tilt & Pan Stellar Series Tenon Mount, Alum AS-0629 - - Coating PNC=Process No Color P_ _=Paint Tube Length 23=23” Tube 37=37” Tube 46=46” Tube 58=58” Tube74=74” Tube AS-3009Clamp Kit SH-0514 Mounting Bracket AS-3004Clamp Kit AS-3010Clamp Kit SH-0514 Mounting Bracket SH-0514 Mounting Bracket Pelco makes adjustable brackets for cameras, sensors and antennas that can mount a variety of traffic industry devices. Video Detection camera brackets are available for mast arm, post top, span wire or side-of-pole applications. 74 84 PNC Vantage Field Service Bulletin Page 1 of 1 Questions? Call the Vantage Product Support Team at (888) 254-5487 Vantage Product Support FIELD SERVICE BULLETIN UPDATE to previous FSB IsotechFSB_3_04.pdf March 2004 Subject: Additional Approved Siamese Cable for Vantage Use Date: October 26, 2006 Re: To All Vantage Dealers Because of continued interest in additional Iteris approved Siamese type video/power cables, and because of the potential problems that have been identified with the use of non-approved cables, a second Siamese cable has been approved for use. The use of the Belden 8281 coaxial cable and a separate power cable that meets our specifications is still the standard, however, if a Siamese cable must be used the following cables are acceptable. The cables must be the manufacturers exact part numbers as listed, use of unapproved cables may negatively affect Vantage system performance and can result in the invalidation of Vantage product and performance warranties. • ISOTEC I59PVCC-00 • Advanced Digital Cable 99163SFX This is a picture of the ISOTEC Siamese cable. It is recommended that the outer cable jacket be cut away completely on the drip loop portion, to reduce strain on the camera BNC and Deutsch connectors. A suitable waterproofing compound should also be used to seal the “Y” junction were the video and power cable exit the outer jacket. This will help to prevent water from wicking down the cable and accumulating inside. 100% SWEEP TESTED 1MHz TO 1GHz 75W Precision Video Coaxial Cable/ Double Braided RG 59/U Type 20 AWG SOLID BC 1 ST COMPONENT AWG (Strand)Dielectric Shield Type Jacket Cable Color Nom. Cap.Vel. Of Nom. Imp. Size/Type Type Coverage Type &&pF/ft.Prop. Nom. D.C.R.Nom. Od Nom. D.C.R.Thickness Jacket OD pF/m. 20 AWG Solid Polyethylene 98% TC X 2 Polyethylene Black 20.9 pF/ft 67%75W Solid BC .198"1.1 W/M'.035".304"68.7 pF/m 10.2 W/M'3.6 W/km 33.1 W/km Frequency Nom. Atten.Nom. Atten.Frequency Nom. Atten.Nom. Atten. MHz (dB/100ft)(dB/100m)MHz (dB/100ft)(dB/100m) 1 0.14 0.46 135 2.58 8.46 3.58 0.47 1.54 143 2.62 8.59 5 0.54 1.77 180 2.79 9.15 7 0.62 2.03 270 4.36 14.30 10 0.68 2.23 360 4.98 16.33 67.5 2.02 6.63 540 6.68 21.91 71.05 2.10 6.89 720 7.82 25.65 100 2.50 8.20 1000 9.18 30.11 2 ND COMPONENT No. of Conductor Insulation Color Nom.Nom.Jacket type Jacket O.D. Conductors Size and Type & Code Capacitance Impedance && Material Thickness Thickness Color 3 16 AWG PVC Black, White,19 pF/ft 80%PVC Pressure .340" +/- .005" 19/29 BC .032"Green 62.3 pF/ft with tape & fillers Black .040" +/- .003" Isotec Product Jacket Cable Color Copper Shipping Number Type &&Weight Weight UL Style Thickness Jacket OD LBS/MFT LBS/MFT I59PVCC-00 PE BLACK 59.86 LBS/MFT 168 LBS/MFT .030".592" UL: n/a +/- .005"+/- .005" CSA: n/a PRINT LEGEND: I59PVCC-00 TRAFFIC CONTROL CABLE 16-3C 600V/PRECISION VIDEO "DIR BUR" "SUN RES" MFG BY ISOTEC ACCEPTANCE OF ABOVE DESIGN:__________________________________________________DATE:___________________________________ Shipping Tolerance: +/- 10% Length Tolerance: +/- 10% Random/Odd Length Tolerance: May ship up to 15% of order total on random/odd lengths. Isotec makes every effort to provide accurate specifications. Printing errors are subject to correction. Standard product specifications are subject to change without notice. Contact your Isotec sales person for current specifications. Rev: 02/09/04 ATTENUATION