Loading...
HomeMy WebLinkAboutCAG-20-065 - Duvall - Underground Drainage i Washington State ♦/ Department of Transportation, Request for Approval of Material Contract Number FA Number N/A SR Duvall Ave NE Date CAG 20-065 8/23/2021 Section/Title of Project Duvall Ave NE County King Contractor Reed Trucking & Excavating, Inc. !Subcontractor Northwest Linings & Geotextile Products, Inc. This form shall be completed prior to submittal.If this form is not compete at time of submittal It may For WSDOT Use Only be returned for information that was omitted. RAM# 01 PE Use Bid Item Material or Name and Location of Fabricator, Specification PEIQPL HdgtrJQPL HQ Use No. Product/Type Manufacturer or Pit Number Reference Code Code A33 Propex Geo 601 Propex Operating Co INC Chattanooga TN 2-12 2 roject E gineer-,, . : r dye Date State Materials Engineer/Representative Date ..df�_ 8 7.,%1 • ptance • • ion Codes for use by Engineer and State Materials Laboratory 1. Acce.1 nce «" aria: Acceptance based upon"Satisfactory'Test Report for samples of materials to be incorporated into prof 0 Acceptance Criteria: Mfg.Cert.of Compliance for'Acceptance'prior to use of material. 3. Acceptance Criteria: Catalog Cuts for'Acceptance'prior to use of material.Catalog Cut Approved ❑Yes ❑No 4. Acceptance Criteria: Submit Shop Drawings for'Approval'prior to fabrication of material. 5. Acceptance Criteria: Only'Approved for Shipment','WSDOT Inspected'or'Fabrication Approved Decal'material shall be used. 6. Acceptance Criteria: Submit Certificate of Materials Origin to Project Engineer Office. 7. Acceptance Criteria: Request Transmitted to State Materials Laboratory for Approval Action. 8. Source Approved: 9. Approval Withheld: Submit samples for preliminary evaluation. 10. Approval Withheld: 11. Miscellaneous Acceptance Criteria. Remarks (PE): Remarks (HO): DOT Form 350-071 Project Engineer Distribution Revised 03/2021 ®Contractor Region Operations Engineer El Fabrication Inspection El Region Materials El State Materials Lab-MS 47365 GEOTEX Product Data Nonwoven GEOTEX® 601 GEOTEX® 601 is a polypropylene, staple fiber, needle-punched nonwoven geotextile produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. The fibers are needled to form a stable network that retains dimensional stability relative to each other. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX® 601 conforms to the property values listed below,. Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute - Laboratory Accreditation Program (GAI-LAP). This product is NTPEP tested for AASHTO standards. MARV2 PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS %U.S. Manufactured 100% 100% MECHANICAL Grab Tensile Strength ASTM D-4632 160 lbs 712 N Grab Elongation ASTM D-4632 50% 50% CBR Puncture ASTM D-6241 410 lbs 1824 N Trapezoidal Tear ASTM D-4533 60 lbs 267 N Mass (typical) ASTM D-5199 6 oz/yd2 203 g/m2 ENDURANCE UV Resistance at 500 hrs ASTM D-4355 70% 70% HYDRAUUC Apparent Opening Size(AOS)3 ASTM D-4751 70 US Std.Sieve 0.212 mm Permittivity ASTM D-4491 1.5 sec-1 1.5 sec-1 Water Flow Rate ASTM D-4491 110 gpm/ft2 4482 I/min/m2 ROLLSIZES4 12.5 ft x 360 ft 3.81 m x 109.8 m 15 ft x 300 ft 4.57 m x 91.5 m NOTES: 1. The property values listed above are effective 12/17/2018 and are subject to change without notice. 2. Values shown are in weaker principal direction.Minimum average roll values(MARV)are calculated as the typical minus two standard deviations. Statistically,it yields a 97.7%degree of confidence that any samples taken from quality assurance testing will exceed the value reported. Values represent testing at time of manufacture. 3. Maximum average roll value. 4. Contact your local Territory Business Manager(TBM)for custom widths and colors.Lead times may vary depending on customer requirements and volume requested. 40 Propex" TM ENGINEERED EARTH SOLUTIONS 40 G►' GEOSOLUTIONS www.propexglobal.com Propex Operating Company,LLC•4019 Industry Drive Chattanooga,TN 37416•ph 800 621 1273 ph 423 855 1466 ARMORMAXe,PYRAMATe,LANDLOKe, X3e,PYRAWALLe,SCOURLOKe,GEOTEX',PETROMAT',PETROTAC',REFLECTEXe,and GRIDPROT°are registered trademarks of Propex Operating Company,LLC. This publication should not be construed as engineering advice.While information contained in this publication is accurate to the bast of our knowledge,Propex does not warrant its accuracy or completeness The ultimate customer and user of the products should assume sole responsibility for the final determination of the suitability of the information and the products for the contemplated and actual use The only warranty made by Propes for its products is set forth in our product data sheets for the product,or such other written warranty as may be agreed by Propex and individual customers Propex specifically disclaims all other warranties,express or implied,including without limitation,warranties of merchantability or fitness for a particular purpose,or arising from provision of samples,a course of dealing or usage of trade. 0 2019 Propex Operating Company,LLC Washington State 3d# Department of Transportation Qualified Product List Product Information Manufacturer : Propex Operating Co. LLC (Formerly Propex, Inc. - Ringgold, GA), Chattanooga - TN Product Name : Geotex 601 Standard Spec : 9-33.2(1), Geotextile - Underground Drainage - Tables 1 and 2 Product Description : Underground Drainage: Nonwoven fabric; Low and Moderate Survivability Class A and B Product Restriction : Acceptance Code : 7021 Code Description : A Aeccptancc of gcotcxtHc for • meet r-he reguiremen} of thp�rp cIfirrati ns under which it is lisi:ed Samplco oLaLL IIILIude the listed lrrforrnatlurr Iri 9-33.4(4). Samples rnusl be submitted to the State B - Acceptance of geotextile for underground drainage in quantities less than or equal to 100 sq. yards, and all quantities of geotextile for soil stabilization, separation, permanent erosion control and prefabricated drainage mat shall be an acceptable Manufacturer's Certificate of Compliance conforming to WSDOT Standard Specification 1-06.3 with each delivery. Samples shall include the listed information in 9-33.4(4). Last Updated : Mar 13, 2012 Contractors with WSDOT Click here for Contractor Product Info Page Copyright WSDOT©2016