HomeMy WebLinkAboutR-397822CAT6
ANTENNA CABLE
ACCESS F
OMNID
DETAIL 1: ANTENNA AND ACCESS POINT MOUNTING
NOT TO SCALE
NOTES:
0 1. THE ROUTE 101 ANTENNA, ACCESS POINT, AND ACCESS POINT MOUNTING ASSEMBLY WILL
BE PROVIDED BY KING COUNTY. THE CONTRACTOR SHALL INSTALL THE ANTENNA, ACCESS
POINT, AND MOUNTING ASSEMBLY ON THE LUMINAIRE ARM OR MAST ARM AS NOTED IN THE
PLANS.
Z 2. SEE PLAN SHEET FOR INTERSECTION SPECIFIC MOUNTING LOCATION FOR ACCESS POINTS
a
� INSTALLED ON MAST ARM. ACCESS POINT SHALL BE MOUNTED ON THE OPPOSITE SIDE OF
THE MAST ARM FROM THE SIGNAL HEADS. VERIFY LOCATION WITH PROJECT REPRESENTATIVE
0 PRIOR TO INSTALLATION.
Of
3. CHASE NIPPLES SHALL BE FILLED WITH SILICONE RUBBER, ROOM TEMPERATURE VULCANIZED
o (RTV) OR OTHER APPROVED SEALANT.
0
a
i 0 4. CONTRACTOR SHALL CONNECT THE CAT6 CABLE TO THE ACCESS POINT.
5. COIL CAT6 CABLE INTO 6—INCH DRIP LOOP PRIOR TO PULLING CABLE INTO LUMINAIRE ARM/MAST
a ARM. SECURELY FASTEN DRIP LOOP WITH TIE WRAP TO THE LUMINAIRE ARM OR MAST ARM.
4 y o
s 3 �
r T�
O U
—cE3a
ola
� o p
N � �
�no pU
O M f
io 4 �1g0AK7
aF Wasyr f
N N m - FEDAID: CM-1292(002) ti Rw
719SecondAw.Suit. UM F RECORD DRAWING
n
z° ^ a Seattle, Washin ton 98104 mformodon shown on tms po—rdn. dmnd
O. CALL 48 HOURS 9 desndbesns-desi a d9
a yne nomponen s nn /or
o (206) 382-9800 a E4 as constructed components. Information
M� w BEFORE YOU DIG sSr � gnrdi.9 ns-n—t—tk —ponents —
aO W Q WNM1V.di(SaseoClates.Com ONAL provided by others and was not verified.
1-800-424-55555 NO
xax:�
DETAIL 2: LUMINAIRE ARM/MAST ARM MOUNTED
ANTENNA AND ACCESS POINT
REVISION
NOT TO SCALE
BY I DATE I APPR I --m.
DATUM
CAMERA / HOUSING
Li
DRIP LOOP
H
0
Li
w
0
0
r,
TILT Fc PAN BRACKET
VIDEO SPLICE ENCLOSURE WITH
WEATHER TIGHT CABLE ENTRANCES
CABLE CLAMP
(BAND CLAMP IS UNACCEPTABLE)
ARM
DETAIL 3: MAST ARM MOUNTED VIDEO DETECTION
NOT TO SCALE
GENERAL NOTES:
1. ALL GROMMET ENTRANCES SHALL BE SUITABLE FOR THE SIZE
AND SHAPE OF CABLE.
2. CAMERA ROTATION IN HOUSINGS TO BE ADJUSTED TO PROVIDE
LEVEL MONITOR PICTURE.
3. DRIP LOOP SHALL BE 6 TO 8 INCHES.
4. ALL HARDWAYRE FASTENERS SHALL BE STAINLESS STEEL,
TORQUED TO MANUFACTURER'S RECOMMENDATIONS WITH
LOCKNUTS.
5. POWER LEADS SHALL BE INSTALLED WITH SUITABLE COPPER
OPEN SPACES.
6. BNC CONNECTORS SHALL CONFORM TO VIDEO VENDORS
RECOMMENDATION.
7. CONTRACTOR SHALL UTILIZE TOOLS AS RECOMMENDED BY VIDEO
VENDOR.
8. TILT AND PAN BRACKET, SENSOR BRACKET SHALL BE ALODINED
ALUMINUM.
9. THE UNIVERSAL HUB PLATE SHALL BE CAST ALUMINUM —
6063—T6.
10. ALL FASTENER PENETRATIONS OF CABINET SHALL BE SEALED
WITH APPROVED METHOD.
Approved For Bid
Robert M. Hanson P.E. Date
(a CITY OF
RENTON VIDEO DETECTION DETAIL
Public Works Department
Approved For Construction ANTENNA DETAIL
Robert M. Hanson P.E. Date
SD-2