Press Alt + R to read the document text or Alt + P to download or print.
This document contains no pages.
HomeMy WebLinkAboutRS_ Lighting Impingement Study_Apron E _ 200120_v2 .pdf
RENTON, WA
Lot S1
Light Impingement Study
PROJECT # 35989
January 28, 2020
Prepared by:
RECEIVED
02/06/2020
amorganroth
PLANNING DIVISION
Lot S1 Light Impingement Study
Project # 35989
Page 2 of 10
TABLE OF CONTENTS
I. EXECUTIVE SUMMARY ..................................................................................... 3
II. BACKGROUND ................................................................................................. 3
III. OBSERVATIONS ............................................................................................... 4
IV. DATA COLLECTION ........................................................................................... 5
A. Field Light Illumination Measurements ............................................................ 5
B. Photometric Calculations & Lighting Models ................................................... 7
V. ANALYSIS ......................................................................................................... 9
A. Lighting Model .................................................................................................. 9
B. Field Light Illumination Measurements ............................................................ 9
APPENDIX:
• Lighting Fixture Cutsheets
Lot S1 Light Impingement Study
Project # 35989
Page 3 of 10
I. EXECUTIVE SUMMARY
This study evaluates the potential light impingement of nearby residents and public
waterways along Boeing’s Lot S1 property. Lighting calculations based on the proposed
Apron E layout including the 5-70 paint hangar show minimal light level contribution
impinging along the shoreline of the Cedar River and the residential housing along Burnett
Avenue North.
Casne Engineering also took field light illumination measurements just outside of the Lot S1
perimeter and along Burnett Ave North, reflecting the initial conditions of the project area
before construction. Another set of field light illumination measurement can be taken after
the construction of project site and compared to the initial field measurements to verify that
there is minimal light level contribution to the Cedar River, or residential housing along
Burnett Avenue North.
II. BACKGROUND
Boeing Parking Lot S1 is located at the south end of the Renton site, south of North 6 th Street
and west of Logan Avenue North, as shown in Figure 1. Casne Engineering has been selected
to provide the electrical design of a new 60,000 square-foot, Certified LEED Silver, paint
hangar building (5-70 building), and three (3) pre-flight Apron E production stalls. The
existing parking lot lighting will be demolished as part of the scope of work for this project.
Due to the project site’s close-proximity to public roadways and neighborhoods a light
impingement study has been requested to insure surrounding areas are minimally impacted.
Casne Engineering has worked on several lighting improvement projects on the Boeing,
Renton site and has conducted lighting studies for projects near public areas and waterways
where light impingement is critical. Most notably this includes site lighting projects for Apron
A, Apron D, and Apron R along the Cedar River and Lake Washington shorelines.
This study includes recording field illumination measurements around the Lot S1 perimeter
and simulated photometric calculations for the proposed Apron E pre-flight stalls and 5-70
paint hangar. Photometric models were used to assist in fixture selection, mounting heights,
and fixture aiming to maximize safety of the work area while minimizing the impact of the
surrounding areas.
Rev. 1
01.20.20
Lot S1 Light Impingement Study
Project # 35989
Page 4 of 10
Figure 1: Lot S1 Area Map
III. OBSERVATIONS
Light illumination data was collected by Casne Engineering from 10:00 PM to 12:00 AM on
May 5, 2019. Weather conditions were clear and 60°F. The sun set at 8:27 PM. The phase of
the moon was a slender crescent.
Lot S1 is a concrete parking lot area located at the southwest corner of North 6th Street and
Logan Avenue North (see Figure 1). This lot provides open-air parking to employees and staff
of the Boeing, Renton site and is well lit. To the west of Lot S1 are existing pre-flight
production stalls, identified as Apron D, with the Cedar River located further to the west. The
5-28 fire station building is located in the southwest corner of Lot S1. Directly south of Lot
S1 is a 50,000 square-foot parking area for the Renton Memorial Stadium. On both the north
and east sides of Lot S1 are public roadways.
Logan Avenue North runs parallel to Lot S1 and contains a bikeway with sidewalk lighting
installed every 150 feet and mounted at approximately 30-feet above finished grade. Further
Lot S1 Light Impingement Study
Project # 35989
Page 5 of 10
to the east of Logan Avenue is a parking area 100-feet wide that runs the length of Logan
Avenue North between North 6th Street and North 4th Street. Residential housing is located
on the east side of the parallel street Burnett Avenue North and is approximately 250-feet
away from the project site area. Logan Avenue North is well lit and designed with pedestrian
safety in mind. Several of these fixtures providing pedestrian and bikeway lighting were not
illuminated during observation. The nearby residential area is screened from the adjacent
parking lot and sidewalk lighting by a row of mature, large canopy, trees.
The shoreline of the Cedar River is approximately 600-feet west of the project site area and
bordered by the Cedar River Trail public walkway. Dense shrubbery and berm landscaping
lines the edge of the Cedar River, providing reduced exposure to adjacent lighting.
IV. DATA COLLECTION
A. Field Light Illumination Measurements
Field illumination data was collected using a Sper Scientific 840020 handheld visible light
meter with In-Range Display settings of 0-3.720 Foot Candle (fc) with a .001 fc resolution and
settings of 3.35-37.20 fc with a resolution of .01 fc. Calibration of this unit was last performed
on June 18th, 2018. Horizontal illumination readings were collected at 36” above grade at 30-
foot intervals and recorded on site plans. To establish baseline readings, t he Lot S1 parking
lot fixtures were turned off and metered readings were recorded around the project site
perimeter, along the sidewalk east of Logan Avenue North, and along the sidewalk east of
Burnett Avenue North as shown in Figure 2. Logan Avenue North sidewalk and bikeway
lighting remained energized except for fixtures observed as not illuminated.
Lot S1 Light Impingement Study
Project # 35989
Page 6 of 10
Figure 2: Lot S1 Perimeter Illumination Measurements (Lot S1 Lights Off)
The minimum, maximum, and average field readings recorded are shown in Table 1 below.
Table 1: Baseline Recorded Values
N 6th St Logan Ave N
(West Side)
South of
Lot S1 Apron D Logan Ave N
(East Side)
Burnett
Ave N
Min 0.3 0.1 0 0.6 0.5 0.1
Max 12 7.2 0.3 12 17 1.5
Average 5.0 1.1 0.0 4.3 5.2 0.4
Lot S1 Light Impingement Study
Project # 35989
Page 7 of 10
B. Photometric Calculations & Lighting Models
AGi32 Lighting Analysis software was used to create photometric calculations of the project
area. Results are displayed in foot-candles (fc) where 1 fc of illuminance is equal to the
intensity of 1 candle, measured 1-foot away from a one-square foot surface. 1 fc is equal to
10.76 lux (or 10.76 lumens). Results are rounded to the nearest one-tenth of a foot-candle.
Lighting fixture photometric data used in the calculation was provided by fixture
manufacturer .ies files with a Light Loss Factor (LLF) of .85, standard for clean, outdoor
environments with large amounts of concrete. Reflectance (p) values were calculated at .25,
standard for concrete, light gray; cement, rough. Modeled results include fixture aiming
points that should be matched during installation. See Figure 3 for lighting calculations along
the Cedar River, along Logan Avenue North, and along Burnett Avenue North.
Figure 3: Apron E Stalls and 5-70 Paint Hangar Lighting Model – Photometric Calculation (fc)
Rev. 1
01.20.20
Lot S1 Light Impingement Study
Project # 35989
Page 8 of 10
The Apron E stall lights are 440W LED fixtures, mounted on 36’ high light poles, and
systematically aimed at the airplane positions. The 5-70 Paint Hangar has three types of
exterior light fixtures. One of the fixture types is a 300W LED floodlight mounted 60’ above
the ground and aimed at the airplane tow path. The 5-70 Paint Hangar has 6 of these
floodlights. Another light fixture type is a 52W LED wall pack mounted 12’ above the ground
and located approximately every 50’ all the way around the 5-70 Paint Hangar. The third light
fixture type is a 10W LED wall pack mounted above the exterior Paint Hangar man doors.
The parking lot lights are 288W LED fixtures mounted on 40’ high light poles. See Figure 4 for
proposed lighting layout. See Table 2 for lighting fixture schedule.
Figure 4: Proposed Lighting Layout
Rev. 1
01.20.20
Lot S1 Light Impingement Study
Project # 35989
Page 9 of 10
Table 2: Fixture Schedule
V. ANALYSIS
A. Lighting Model
Simulated lighting calculations include only fixtures proposed to be installed as part of this
project. Accurate photometric information for existing fixtures outside of the project site
area could not be located and subsequently was not included in the final lighting model. The
results shown should be considered the delta between the existing conditions and the
proposed. Results are calculated and shown in horizontal foot -candles, which measures
illuminance on a horizontal axis.
Modeled results show that minimal light contribution extends outside the project site
perimeter with values decreasing to a delta of 0.0 fc within less than 150 -feet from the
project perimeter. Similar results are calculated for the shoreline of the Cedar River and
along the residential area east of Burnett Avenue.
B. Field Light Illumination Measurements
The field light illumination measurements shown in Figure 2 serve as the initial conditions,
showing the existing light levels along the perimeter of Lot S1 and residential housing along
Burnett Ave North before the Apron E Expansion Stall and 5-70 Paint Hangar lighting
installation. Another set of field light illumination measurement can be taken after the
construction of project site and compared to the initial field measurements to verify that
there is minimal light level contribution to the Cedar River, or residential housing along
Burnett Avenue North.
Type Description Voltage Watts Color Manufacturer Location Mounting
A1 LED Floodlight 480V 440W 4000K
Meteor Lighting, Bolt Series
Outdoor/Natatorium BTS-440-408-
HVT-STV-80-BLK-BRK-GSV-SLP-OUT
Stalls Pole
B1 LED Area Light 480V 188W 4000K LSI XGBM-FT-LED-SS-NW-480 Stalls Pole
B2 LED Area Light 480V 288W 4000K LSI XGBM-5-LED-HO-NW-480 Parking Lot Pole
W1 LED Wall Pack 277V 52W 4000K RAB WPLEDFC52N Building Exterior Wall
W2 LED Wall Pack 277V 10W 4000K RAB WPLED10NS Building Exterior Wall
W3 LED Floodlight 277V 300W 4000K RAB FXLED300SFN Building Exterior Wall
Lot S1 Light Impingement Study
Project # 35989
Page 10 of 10
APPENDIX
Specification
ADVANCED HIGH CEILING
METEOR LIGHTING P: 213.255.2060 F: 213.596.3704 www.meteor-lighting.com
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
2018 V1.3 | Page 1 of 6
Electrical System
- 16120lm (150W)
29274lm (220W)
34505lm (280W)
51306lm (440W)
68340lm (560W)
- Power Input: Universal (120-277V); HVT (347-480V)
- Operating Temperature: -40°F~104°F
- Surge Protection: 10KV
LED Technology EPA
- 3000K, 4000K, 5000K
- 85 CRI, 75 CRI
- Beam Angle: 15°, 30°, 60° , 80° and 100° (with diffuser)
- Rated Life > 60,000 Hours (L70)
Advanced Dimming
- Standard 0-10V: dims to 10%
Project
Type
Note
Quantity
- BTS-150 / BTS-220 / BTS-280: 1.28 ft2
- BTS-440 / BTS-560: 2.37 ft2
Warranty
- 5 year limited warranty
Housing
- Dimensions: 8.67” (220mm) x 14.96” (380mm) x 5.79” (147mm)
- Material: Die-Cast Aluminum, Tempered Glass
- Weight: 9.26lbs (BTS-150) / 17.64lbs (BTS-220) / 18.52lbs (BTS-280) /
48.5lbs (BTS-440/560)
Mounting
- Bracket
(Proprietary VX Driver is incorporated to all dimming options for video flicker-free lighting)
Not all Bolt Series are DLC qualified.
For all qualified products.
Please visit: www.designlights.org/qpl
17
Bolt Series - Outdoor/Natatorium Rating
High lumen compact modular luminaire with lumen output 13608 – 68340lm suited
for sporting facilities.
- Outdoor/Natatorium Rating
Special coating, sealant, and wiring is applied for long term operation in harsh
environments.
Standard version available, please refer to Standard spec sheet for more details.
Listing
- UL Wet Location Listed, IP65 Outdoor Rating
- DLC Listed
- FCC
- CE
A1
440
Exterior,
Stall Lighting
METEOR BTS-440-408-HVT-
STV-80-BLK-BRK-GSV-SLP-OUT
Specification
ADVANCED HIGH CEILING
METEOR LIGHTING P: 213.255.2060 F: 213.596.3704 www.meteor-lighting.com
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
2018 V1.3 | Page 2 of 6
How To Specify:
BTS
Bolt Series
Model
150 150W
220 220W
280 280W
440 440W
560 560W
Wattage
BLK Black
WHT White
Finish
UNV 120-277V
HVT 347-480V
Voltage
15 15º
30 30º
60 60º
80 80º
WD 100º (with diffuser)
Beam Angle
308 3000K / CRI85
408 4000K / CRI85
507 5000K / CRI75
CCT / CRI
STV Standard 0-10V dims to 10%
Dimming
Ordering Example: BTS-560-507-UNV-STV-15-BLK-BRK-WG
BTS
Mounting
BRK Bracket
4-5 weeks lead time on over 75% of specifications.
DesignLights Consortium™ Qualified Luminaires:
DLC QPL Model Number : BTS-560-50K, BTS-150-CC7-UNV, BTS-220-CC7-UNV, BTS-280-CC7-UNV
Not all product variations listed on this page are DLC qualified.
To ensure that a specific model is qualified, visit www.designlights.org/search.
* Please factor in change in lumen
output with diffuser (-20% with
WD ).
1 Please factor in change in lumen output of -14%.
2 Please factor in change in lumen output of -40%.
3 Please factor in change in lumen output of -25%.
4 Please factor in change in lumen output with
diffuser (-20% with DF).
Bolt Series - Outdoor/Natatorium Rating
Accessories Rating
WG1
GSB2
GSV3
DF4
SLP
OUT1
NAT 2
Wire Guard
Glare Shield Baffle
Glare Shield Visor
Diffuser
Slipfitter
Outing Rating
Natatorium Rating
1 Outdoor rating: Coating and wiring will
be changed to high UV resistant and
corrosion resistant materials for long
term operation in outdoor environments.
2 Natatorium rating: Coating and sealant
will be changed to high corrosion
resistant materials to prevent damage from
long term exposure to chlorine vapors.
-OUT
Specification
ADVANCED HIGH CEILING
METEOR LIGHTING P: 213.255.2060 F: 213.596.3704 www.meteor-lighting.com
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
2018 V1.3 | Page 3 of 6
22896 lm13608 lm 27324 lm 40174 lm
24486 lm14256 lm 29160 lm 42930 lm
29274 lm16120 lm 34505 lm 51306 lm 68340 lm
57240 lm
53530 lm
CCT
3000K
5000K
280W220W150W 440W 560W
4000K
Delivered Lumens*
*Tolerance±8%
Current Consumption
120V 277V
150W 1.38A 0.60A
0.87A
1.11A
1.75A
2.22A
2.02A
2.57A
4.03A
5.13A
220W
280W
440W
560W
Beam Angle: 15°
Wattage
Wattage
Volt
Bolt Series - Outdoor/Natatorium Rating
Specification
ADVANCED HIGH CEILING
METEOR LIGHTING P: 213.255.2060 F: 213.596.3704 www.meteor-lighting.com
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
2018 V1.3 | Page 4 of 6
150W / 220W / 280W
18.26”
10.6”
3.9”Ø0.87”Ø7.87”
0.87”
0.4”
8.7”
3.03”7.87”Dimensions
Bolt Series - Outdoor/Natatorium Rating
Specification
ADVANCED HIGH CEILING
METEOR LIGHTING P: 213.255.2060 F: 213.596.3704 www.meteor-lighting.com
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
2018 V1.3 | Page 5 of 6
Dimensions
Bolt Series - Outdoor/Natatorium Rating
Dimensions
440W / 560W
90º
0.87”
0.41”
30º
30º2.8”
10.78”
9.13”
18.74”
11.41”
9.84”
3.14”
4.72”
17.91”
7.87”
0.55”
Stainless Steel
Specification
ADVANCED HIGH CEILING
METEOR LIGHTING P: 213.255.2060 F: 213.596.3704 www.meteor-lighting.com
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
2018 V1.3 | Page 6 of 6
Bolt Series - Outdoor/Natatorium Rating
Accessory
Glare Shield Baffle Glare Shield Visor
Wire Guard
Slipfitter
3 ¼”
¼”
4 ½”
½”
4”
∅1
∅3
Tenon slipfitter; fits 2-3/8" to
2-7/8" OD tenon.
5.3”
5.3”5.3”
1’- 5¼”
1’- 4¼”
© 2017
LSI INDUSTRIES INC.
Project Name Fixture Type
Catalog #
10/16/17
DOE LIGHTING FACTS
Department of Energy has verified representative product test
data and results in accordance with its Lighting Facts Program.
Visit www.lightingfacts.com for specific catalog strings.
SMARTTEC™ THERMAL CONTROL - LSI drivers feature integral sensor which reduces
drive current when ambient temperatures exceed rated temperature.
OCCUPANCY SENSING (IMS) – Optional integral passive infrared motion sensor activates
switching of luminaire light levels. High level light is activated and increased to full bright
in 1-2 seconds upon detection of motion. Low light level (30% maximum drive current)
is activated when target zone is absent of motion activity for ~2 minutes and ramps
down (10-15 seconds) to low level to allow eyes time to adjust. Sensor is located on the
front of optical assembly and rotates with the optic. Sensor optic has a detection cone of
approximately 45°. Examples of detection – occurs 30' out from a 30' mounting height
pole; occurs 20' out from a 20' mounting height pole.
ENERGY SAVING CONTROL OPTIONS – DIM – 0-10 volt dimming enabled with controls
by others. BLS – Bi-level switching responds to external line voltage signal from separate
120-277V controller or sensor (by others), with low light level decreased to 30% maximum
drive current.
LEDS - Select high-brightness LEDs in Cool White (5000K) or Neutral White (4000K) color
temperature, 70 CRI.
DISTRIBUTION/PERFORMANCE - Types 3, 5, FT and FTA available - field rotatable
reflectors.
HOUSING - Square, die-formed aluminum. Fully enclosed weather-tight housing contains
factory prewired drivers and field connections.
TOP-ACCESS COVER - Gasketed, tethered top-access cover provides ease of installation
and allows for easy driver access. Four captive stainless-steel fasteners secure the top-
access cover to the housing.
OPTICAL UNIT - Clear tempered optical grade flat glass lens sealed to aluminum housing
creates an IP67 rated, sealed optical unit (includes pressure stabilizing breather). Optical
unit can be easily field rotated in 90o increments. Directional arrow on optics allows
alignment without the unit being energized.
MOUNTING - 2-1/2” x 5-3/8” x 12” extruded aluminum arm mounting bracket shipped
standard. Use with 5” traditional drilling pattern. Round Pole Plate (RPP2) required for
mounting to 3”– 5” round poles. (See Accessory Ordering Information chart.)
ELECTRICAL - Two-stage surge protection (including separate surge protection built into
electronic driver) meets IEEE C62.41.2-2002, Location Category C. Available with universal
voltage power supply 120-277VAC (UE - 50/60Hz input), and 347-480VAC.
DRIVERS - Available in Low Watt (LW), Super Saver (SS) and High Output (HO) drive
currents (Drive currents are factory programmed). Components are fully encased in
potting material for moisture resistance. Driver complies with FCC 47 CFR part 15 RFI/EMI
standard.
OPERATING TEMPERATURE - -40°C to +50°C (-40°F to +122°F).
FINISH - Fixtures are finished with LSI's DuraGrip® polyester powder coat finishing process.
The DuraGrip finish withstands extreme weather changes without cracking or peeling.
DECAL STRIPING - LSI offers optional color-coordinated decals in 9 standard colors to
accent the fixture. Decals are guaranteed for five years against peeling, cracking, or fading.
WARRANTY - LSI LED fixtures carry a limited 5-year warranty.
PHOTOMETRICS - Please visit our web site at www.lsi-industries.com for detailed
photometric data.
SHIPPING WEIGHT (IN CARTON) - Fixture - 44.5 lbs (20 kg) Arm - 5 lbs. (2kg) arm
LISTING - UL listed to U.S. and Canadian safety standards. Suitable for wet locations. For
a list of the specific products in this series that are DLC listed, please consult the LED
Lighting section of our website or the Design Lights website at www.designlights.org.
LED AREA LIGHTS - (XGBM)
US patent D574994 & 7,828,456 and MX patent 29631 and US & Int'l. patents pending
Type 3 Type 5 Type FT Type FTA
LIGHT OUTPUT - XGBM
Lumens (Nominal)Watts
(Nominal)
LW 14080 13840 15020 16560 140
SS 20180 18040 20700 23030 187
HO 26750 25460 29070 31810 300
LW 11450 11290 12220 13470 136
SS 16390 15170 17230 18750 188
HO 22240 20550 23510 25410 288 Cool WhiteNeutral WhiteLED Chips are frequently updated therefore values may increase.
Shown with optional decal striping
This product, or selected versions of this product, meet the standards listed below. Please consult factory for your specific requirements.
wet location
ARRAFunding Compliant
IP67
Fixtures comply with ANSI C136.31-2010 American National Standard for Roadway Lighting
Equipment - Luminaire Vibration 3G requirements.
B1
188
Exterior, Stall
Area Lighting
LSI XGBM-FT-
LED-SS-NW-480
© 2017
LSI INDUSTRIES INC.
Project Name Fixture Type
Catalog #
10/16/17
Prefix FinishColorTemperature
XGBM1 -
LED
Greenbriar
LED CW - Cool White
(5000K)
NW - Neutral White
(4000K)
Input Voltage
UE - Universal
Voltage
(120-277)
347-480
BLK - Black
BRZ - Bronze
GPT - Graphite
MSV - Metallic Silver
PLP - Platinum Plus
SVG - Satin Verde
Green
WHT - White
Optional Color Decals
45 – Light Gold
20 – Charcoal Metallic
55 – Black
94 – Blue Metallic
59 – Dark Green
51 – Dark Red
21 – Tomato Red
50 – White
700 – Aztec Silver
Metallic
Optional Sensor/OptionsOptional ControlsLightSourceDistribution
TYPICAL ORDER EXAMPLE:
LUMINAIRE ORDERING INFORMATION
XGBM 5 LED HO CW UE WHT PCM
ACCESSORY ORDERING INFORMATION2 (Accessories are field installed)
482002 BLK7
162914BLK
123111CLR
169010CLR
144191CLR
XGBM-HSS House Side Shield (Black only)
RPP2 - Round Pole Plate
BKS-BO-WM-*-CLR - Wall Mount Plate
BKA-BO-RA-8-CLR - Radius Arm
BKU-BO-S-19-CLR - Upsweep Bracket for round or square poles
FK120 Single Fusing (120V) FK1208
FK277 Single Fusing (277V)FK2778
Description Order Number Order Number
LUMINAIRE EPA CHART2 - XGBM
Single
D180°
D90°
T90°
TN120°
Q90°
8" Bracket 12" Bracket
FOOTNOTES:
1- Use with 5" traditional drilling pattern.
2- For wireless controls information and accessories, see Controls section.
3- Requires a SiteManager and override switch. Not compatible with BLS or
IMS option.
4- Not compatible with IMS or BLS option.
5- Not compatible with wireless controls system, DIM or IMS option.
LW - Low Watt
SS - Super Saver
HO - High Output
DriveCurrent
DFK208,2408
DFK480 Double Fusing (480V) DFK4808
FK347 Single Fusing (347V) FK3478
PMOS120 - 120V Pole-Mount Occupancy Sensor 518030CLR9
PMOS208/240 - 208, 240V Pole-Mount Occupancy Sensor 534239CLR9
PMOS277 - 277V Pole-Mount Occupancy Sensor 518029CLR9
PMOS480 - 480V Pole-Mount Occupancy Sensor 534240CLR9
Description
FT - Forward Throw
FTA - Forward Throw
Automotive
3 - Type III
5 - Type V
2.3
4.7
2.4
4.8
4.7
7.2
7.3
8.8
12" Bracket
Required
6- Not compatible with wireless controls system, DIM or BLS option.
7- House Side Shields add to fixture EPA. Consult factory.
8- Fusing must be located in the hand hole of pole.
9- To be used with any of the PCM/GCM wireless controls systems in the
fixture. Consult factory.
10-Photocell must be ordered separately. 7 pin standard. See Accessories.
Note: House Side Shield adds to fixture
EPA. Consult Factory.
SensorWireless Control System2,3
(blank) - None
PCM - Platinum Control System
PCMH - Host/Satellite Platinum Control
System
GCM - Gold Control System
GCMH - Host/Satellite Gold Control System
DIM - 0-10 volt dimming
(required for satellite fixtures)
ALSC - AirLink Synapse Control System
ALSCH - AirLink Synapse Control System -
Host/Satelite
IMS - Integral Motion Sensor6
PCI120 - 120V Button-Type Photocell
PCI208 - 208V Button-Type Photocell
PCI240 - 240V Button-Type Photocell
PCI277 - 277V Button-Type Photocell
PCI347 - 347V Button-Type Photocell
Options
8BK - 8" Bracket (S and D180 only)
TB - Terminal Block
Stand-Alone Control
(blank) - None
DIM - 0-10 volt dimming4
(from external signal)
BLS - Bi-level Switching5
(from external signal - required
120-277V controls system voltage)
LED AREA LIGHTS - (XGBM)
DIMENSIONS
24” sq. (610 mm)
9”
(229 mm)
12”
(305 mm)
3 15/16”
(99 mm)
13 5/16”
(339 mm)
House Side Shield (482002BLK)
9”
(229 mm)
5/8”
(16 mm)
1-3/8”
(35 mm)
OPTIONAL IMS
2-1/4”
(57 mm)
4-1/8”
(105 mm)
DFK208, 240 Double Fusing (208V, 240V)
© 2017
LSI INDUSTRIES INC.
Project Name Fixture Type
Catalog #
10/16/17
BUG LISTING
CW 26,754 300 89 B3-U0-G3
HO CW-HSS 17,316 288 60 B2-U0-G2
NW 22,240 289 77 B3-U0-G2
NW-HSS 13,941 288 48 B2-U0-G2
CW 14,082 140 100 B2-U0-G2
LW CW-HSS 9205 137 67 B1-U0-G2
NW 11,,451 137 84 B2-U0-G2
NW-HSS 7513 136 55 B1-U0-G2
CW 20181 187 108 B3-U0-G2
SS CW-HSS 13,034 187 70 B2-U0-G2
NW 16,394 189 87 B3-U0-G2
NW-HSS 10,384 189 55 B2-U0-G2
XGBM - Type 3
HO CW 25,464 300 85 B4-U0-G2
NW 20,549 288 71 B4-U0-G2
LW CW 13,842 140 99 B3-U0-G2
NW 11,291 136 83 B3-U0-G2
SS CW 18,044 186 97 B4-U0-G2
NW 15,173 189 80 B4-U0-G2
XGBM - Type 5
CW 31,808 301 106 B4-U0-G4
HO CW-HSS 20,838 288 72 B3-U0-G3
NW 25,407 289 88 B3-U0-G3
NW-HSS 16,855 289 58 B3-U0-G3
CW 16,560 140 118 B3-U0-G2
LW CW-HSS 11,440 137 84 B2-U0-G2
NW 13,473 136 99 B3-U0-G2
NW-HSS 9277 136 68 B2-U0-G2
CW 23,033 187 123 B3-U0-G3
SS CW-HSS 15,213 187 81 B3-U0-G2
NW 18,752 189 99 B3-U0-G3
NW-HSS 12,516 189 66 B2-U0-G3
,
XGBM - Type FTA
CW 29,070 301 97 B2-U0-G4
HO CW-HSS 20,964 288 73 B1-U0-G4
NW 23,512 289 81 B2-U0-G4
NW-HSS 17,191 289 60 B1-U0-G3
CW 15,019 141 107 B1-U0-G3
LW CW-HSS 11,519 137 84 B1-U0-G3
NW 12,217 136 90 B1-U0-G3
NW-HSS 9365 136 69 B1-U0-G3
CW 20,700 187 111 B2-U0-G3
SS CW-HSS 15,273 187 82 B1-U0-G3
NW 17,230 189 91 B1-U0-G3
NW-HSS 12,597 189 67 B1-U0-G3
XGBM - Type FT
Drive Current Color Temp.* Lumens Watts LER BUG Rating Drive Current Color Temp.* Lumens Watts LER BUG Rating
Drive Current Color Temp.* Lumens Watts LER BUG Rating
Drive Current Color Temp.* Lumens Watts LER BUG Rating
* Color Temperature: NW-4000K, CW-5000K
LED AREA LIGHTS - (XGBM)
10/12/17LSI Industries Inc. 10000 Alliance Rd. Cincinnati, OH 45242 • www.lsi-industries.com • (513) 372-3200 • ©LSI Industries Inc. All Rights Reserved.
Optional IMS Coverage Diagram
enabled by Synapse®
Wireless Lighting Controller
The AirLink integrated controller is a California Title 24 compliant lighting
controller that provides real-time light monitoring and control with
utility-grade power monitoring. It includes a 24V sensor input and power
supply to connect up to two (2) sensors into the outdoor AirLink wireless
lighting system.
The wireless integrated controller and twist lock controller are compatible
with this fixture.
Features
• 2% Utility Grade Power Monitoring
• Up to 80% Savings through smart dimming
• True On/Off functionality via switched relay
• Seamlessly integrates into the outdoor AirLink wireless lighting control
solution & Self-healing Mesh Networking
• Relay closes on power loss
• Supports a wide range of LED drivers and fixtures
• Class 1 / Class 2 0-10V Dimming Control
• Direct Connect up to two (2) to 24V Occupancy Sensors and
Photocells (consult sales for compatible list)
• Secure, over-the-air upgrades to support future enhancements
• Excellent RF Range — 1,000ft LoS between controllers
• Available in a metal cased version with quick connect
terminal blocks
• Lights default to on for safety
Specifications
Regulatory Approvals
• FCC, IC, CE certified
• cULus Listed
• California Title 24 compliant
Power and Performance
• Operating environmental: -40°F to 131°F (-40°C to 55°C)
• Input power: 100–277 VAC +/- 10% (Max 305V)47/64 Hz
• Switched output: Default ON; Zero Cross Switching
• Load rating: 5A @ 100V to 277V (+/- 10%)
• Dimming: 0–10V control; Output: Class 1/2 - 20mA Source
Max / 50mA Sink Max
• Power monitoring: Utility grade - 2% accuracy
• Sensors inputs: 0–10V (photocell sensors), 0–24V (all other
sensors); Sensor power supply: 24VDC @ 50mA
Other
• Dimensions: 8.2” L x 2.3” W x 1.3” H (209mm L x 59mm W x
33mm H) without antennas
• Radio: SNAP 2.4 GHz; 802.15.4; +20 dBm Transmit Power;
-105 dBm Receive Sensitivity
• Warranty: 5 years
Sales
controls.sales@lsi-industries.com
Support
controls.support@lsi-industries.com
1 (800) 436-7800 (support, option 8)
More information
For more information on AirLink, visit our
website at www.lsi-airlink.com/airlink
Contact LSI Controls
© 2017
LSI INDUSTRIES INC.
Project Name Fixture Type
Catalog #
10/16/17
DOE LIGHTING FACTS
Department of Energy has verified representative product test
data and results in accordance with its Lighting Facts Program.
Visit www.lightingfacts.com for specific catalog strings.
SMARTTEC™ THERMAL CONTROL - LSI drivers feature integral sensor which reduces
drive current when ambient temperatures exceed rated temperature.
OCCUPANCY SENSING (IMS) – Optional integral passive infrared motion sensor activates
switching of luminaire light levels. High level light is activated and increased to full bright
in 1-2 seconds upon detection of motion. Low light level (30% maximum drive current)
is activated when target zone is absent of motion activity for ~2 minutes and ramps
down (10-15 seconds) to low level to allow eyes time to adjust. Sensor is located on the
front of optical assembly and rotates with the optic. Sensor optic has a detection cone of
approximately 45°. Examples of detection – occurs 30' out from a 30' mounting height
pole; occurs 20' out from a 20' mounting height pole.
ENERGY SAVING CONTROL OPTIONS – DIM – 0-10 volt dimming enabled with controls
by others. BLS – Bi-level switching responds to external line voltage signal from separate
120-277V controller or sensor (by others), with low light level decreased to 30% maximum
drive current.
LEDS - Select high-brightness LEDs in Cool White (5000K) or Neutral White (4000K) color
temperature, 70 CRI.
DISTRIBUTION/PERFORMANCE - Types 3, 5, FT and FTA available - field rotatable
reflectors.
HOUSING - Square, die-formed aluminum. Fully enclosed weather-tight housing contains
factory prewired drivers and field connections.
TOP-ACCESS COVER - Gasketed, tethered top-access cover provides ease of installation
and allows for easy driver access. Four captive stainless-steel fasteners secure the top-
access cover to the housing.
OPTICAL UNIT - Clear tempered optical grade flat glass lens sealed to aluminum housing
creates an IP67 rated, sealed optical unit (includes pressure stabilizing breather). Optical
unit can be easily field rotated in 90o increments. Directional arrow on optics allows
alignment without the unit being energized.
MOUNTING - 2-1/2” x 5-3/8” x 12” extruded aluminum arm mounting bracket shipped
standard. Use with 5” traditional drilling pattern. Round Pole Plate (RPP2) required for
mounting to 3”– 5” round poles. (See Accessory Ordering Information chart.)
ELECTRICAL - Two-stage surge protection (including separate surge protection built into
electronic driver) meets IEEE C62.41.2-2002, Location Category C. Available with universal
voltage power supply 120-277VAC (UE - 50/60Hz input), and 347-480VAC.
DRIVERS - Available in Low Watt (LW), Super Saver (SS) and High Output (HO) drive
currents (Drive currents are factory programmed). Components are fully encased in
potting material for moisture resistance. Driver complies with FCC 47 CFR part 15 RFI/EMI
standard.
OPERATING TEMPERATURE - -40°C to +50°C (-40°F to +122°F).
FINISH - Fixtures are finished with LSI's DuraGrip® polyester powder coat finishing process.
The DuraGrip finish withstands extreme weather changes without cracking or peeling.
DECAL STRIPING - LSI offers optional color-coordinated decals in 9 standard colors to
accent the fixture. Decals are guaranteed for five years against peeling, cracking, or fading.
WARRANTY - LSI LED fixtures carry a limited 5-year warranty.
PHOTOMETRICS - Please visit our web site at www.lsi-industries.com for detailed
photometric data.
SHIPPING WEIGHT (IN CARTON) - Fixture - 44.5 lbs (20 kg) Arm - 5 lbs. (2kg) arm
LISTING - UL listed to U.S. and Canadian safety standards. Suitable for wet locations. For
a list of the specific products in this series that are DLC listed, please consult the LED
Lighting section of our website or the Design Lights website at www.designlights.org.
LED AREA LIGHTS - (XGBM)
US patent D574994 & 7,828,456 and MX patent 29631 and US & Int'l. patents pending
Type 3 Type 5 Type FT Type FTA
LIGHT OUTPUT - XGBM
Lumens (Nominal)Watts
(Nominal)
LW 14080 13840 15020 16560 140
SS 20180 18040 20700 23030 187
HO 26750 25460 29070 31810 300
LW 11450 11290 12220 13470 136
SS 16390 15170 17230 18750 188
HO 22240 20550 23510 25410 288 Cool WhiteNeutral WhiteLED Chips are frequently updated therefore values may increase.
Shown with optional decal striping
This product, or selected versions of this product, meet the standards listed below. Please consult factory for your specific requirements.
wet location
ARRAFunding Compliant
IP67
Fixtures comply with ANSI C136.31-2010 American National Standard for Roadway Lighting
Equipment - Luminaire Vibration 3G requirements.
B2
288
Exterior, Parking
Lot Area Lighting
LSI XGBM-S-LED-
HO-NW-480
© 2017
LSI INDUSTRIES INC.
Project Name Fixture Type
Catalog #
10/16/17
Prefix FinishColorTemperature
XGBM1 -
LED
Greenbriar
LED CW - Cool White
(5000K)
NW - Neutral White
(4000K)
Input Voltage
UE - Universal
Voltage
(120-277)
347-480
BLK - Black
BRZ - Bronze
GPT - Graphite
MSV - Metallic Silver
PLP - Platinum Plus
SVG - Satin Verde
Green
WHT - White
Optional Color Decals
45 – Light Gold
20 – Charcoal Metallic
55 – Black
94 – Blue Metallic
59 – Dark Green
51 – Dark Red
21 – Tomato Red
50 – White
700 – Aztec Silver
Metallic
Optional Sensor/OptionsOptional ControlsLightSourceDistribution
TYPICAL ORDER EXAMPLE:
LUMINAIRE ORDERING INFORMATION
XGBM 5 LED HO CW UE WHT PCM
ACCESSORY ORDERING INFORMATION2 (Accessories are field installed)
482002 BLK7
162914BLK
123111CLR
169010CLR
144191CLR
XGBM-HSS House Side Shield (Black only)
RPP2 - Round Pole Plate
BKS-BO-WM-*-CLR - Wall Mount Plate
BKA-BO-RA-8-CLR - Radius Arm
BKU-BO-S-19-CLR - Upsweep Bracket for round or square poles
FK120 Single Fusing (120V) FK1208
FK277 Single Fusing (277V)FK2778
Description Order Number Order Number
LUMINAIRE EPA CHART2 - XGBM
Single
D180°
D90°
T90°
TN120°
Q90°
8" Bracket 12" Bracket
FOOTNOTES:
1- Use with 5" traditional drilling pattern.
2- For wireless controls information and accessories, see Controls section.
3- Requires a SiteManager and override switch. Not compatible with BLS or
IMS option.
4- Not compatible with IMS or BLS option.
5- Not compatible with wireless controls system, DIM or IMS option.
LW - Low Watt
SS - Super Saver
HO - High Output
DriveCurrent
DFK208,2408
DFK480 Double Fusing (480V) DFK4808
FK347 Single Fusing (347V) FK3478
PMOS120 - 120V Pole-Mount Occupancy Sensor 518030CLR9
PMOS208/240 - 208, 240V Pole-Mount Occupancy Sensor 534239CLR9
PMOS277 - 277V Pole-Mount Occupancy Sensor 518029CLR9
PMOS480 - 480V Pole-Mount Occupancy Sensor 534240CLR9
Description
FT - Forward Throw
FTA - Forward Throw
Automotive
3 - Type III
5 - Type V
2.3
4.7
2.4
4.8
4.7
7.2
7.3
8.8
12" Bracket
Required
6- Not compatible with wireless controls system, DIM or BLS option.
7- House Side Shields add to fixture EPA. Consult factory.
8- Fusing must be located in the hand hole of pole.
9- To be used with any of the PCM/GCM wireless controls systems in the
fixture. Consult factory.
10-Photocell must be ordered separately. 7 pin standard. See Accessories.
Note: House Side Shield adds to fixture
EPA. Consult Factory.
SensorWireless Control System2,3
(blank) - None
PCM - Platinum Control System
PCMH - Host/Satellite Platinum Control
System
GCM - Gold Control System
GCMH - Host/Satellite Gold Control System
DIM - 0-10 volt dimming
(required for satellite fixtures)
ALSC - AirLink Synapse Control System
ALSCH - AirLink Synapse Control System -
Host/Satelite
IMS - Integral Motion Sensor6
PCI120 - 120V Button-Type Photocell
PCI208 - 208V Button-Type Photocell
PCI240 - 240V Button-Type Photocell
PCI277 - 277V Button-Type Photocell
PCI347 - 347V Button-Type Photocell
Options
8BK - 8" Bracket (S and D180 only)
TB - Terminal Block
Stand-Alone Control
(blank) - None
DIM - 0-10 volt dimming4
(from external signal)
BLS - Bi-level Switching5
(from external signal - required
120-277V controls system voltage)
LED AREA LIGHTS - (XGBM)
DIMENSIONS
24” sq. (610 mm)
9”
(229 mm)
12”
(305 mm)
3 15/16”
(99 mm)
13 5/16”
(339 mm)
House Side Shield (482002BLK)
9”
(229 mm)
5/8”
(16 mm)
1-3/8”
(35 mm)
OPTIONAL IMS
2-1/4”
(57 mm)
4-1/8”
(105 mm)
DFK208, 240 Double Fusing (208V, 240V)
© 2017
LSI INDUSTRIES INC.
Project Name Fixture Type
Catalog #
10/16/17
BUG LISTING
CW 26,754 300 89 B3-U0-G3
HO CW-HSS 17,316 288 60 B2-U0-G2
NW 22,240 289 77 B3-U0-G2
NW-HSS 13,941 288 48 B2-U0-G2
CW 14,082 140 100 B2-U0-G2
LW CW-HSS 9205 137 67 B1-U0-G2
NW 11,,451 137 84 B2-U0-G2
NW-HSS 7513 136 55 B1-U0-G2
CW 20181 187 108 B3-U0-G2
SS CW-HSS 13,034 187 70 B2-U0-G2
NW 16,394 189 87 B3-U0-G2
NW-HSS 10,384 189 55 B2-U0-G2
XGBM - Type 3
HO CW 25,464 300 85 B4-U0-G2
NW 20,549 288 71 B4-U0-G2
LW CW 13,842 140 99 B3-U0-G2
NW 11,291 136 83 B3-U0-G2
SS CW 18,044 186 97 B4-U0-G2
NW 15,173 189 80 B4-U0-G2
XGBM - Type 5
CW 31,808 301 106 B4-U0-G4
HO CW-HSS 20,838 288 72 B3-U0-G3
NW 25,407 289 88 B3-U0-G3
NW-HSS 16,855 289 58 B3-U0-G3
CW 16,560 140 118 B3-U0-G2
LW CW-HSS 11,440 137 84 B2-U0-G2
NW 13,473 136 99 B3-U0-G2
NW-HSS 9277 136 68 B2-U0-G2
CW 23,033 187 123 B3-U0-G3
SS CW-HSS 15,213 187 81 B3-U0-G2
NW 18,752 189 99 B3-U0-G3
NW-HSS 12,516 189 66 B2-U0-G3
,
XGBM - Type FTA
CW 29,070 301 97 B2-U0-G4
HO CW-HSS 20,964 288 73 B1-U0-G4
NW 23,512 289 81 B2-U0-G4
NW-HSS 17,191 289 60 B1-U0-G3
CW 15,019 141 107 B1-U0-G3
LW CW-HSS 11,519 137 84 B1-U0-G3
NW 12,217 136 90 B1-U0-G3
NW-HSS 9365 136 69 B1-U0-G3
CW 20,700 187 111 B2-U0-G3
SS CW-HSS 15,273 187 82 B1-U0-G3
NW 17,230 189 91 B1-U0-G3
NW-HSS 12,597 189 67 B1-U0-G3
XGBM - Type FT
Drive Current Color Temp.* Lumens Watts LER BUG Rating Drive Current Color Temp.* Lumens Watts LER BUG Rating
Drive Current Color Temp.* Lumens Watts LER BUG Rating
Drive Current Color Temp.* Lumens Watts LER BUG Rating
* Color Temperature: NW-4000K, CW-5000K
LED AREA LIGHTS - (XGBM)
10/12/17LSI Industries Inc. 10000 Alliance Rd. Cincinnati, OH 45242 • www.lsi-industries.com • (513) 372-3200 • ©LSI Industries Inc. All Rights Reserved.
Optional IMS Coverage Diagram
enabled by Synapse®
Wireless Lighting Controller
The AirLink integrated controller is a California Title 24 compliant lighting
controller that provides real-time light monitoring and control with
utility-grade power monitoring. It includes a 24V sensor input and power
supply to connect up to two (2) sensors into the outdoor AirLink wireless
lighting system.
The wireless integrated controller and twist lock controller are compatible
with this fixture.
Features
• 2% Utility Grade Power Monitoring
• Up to 80% Savings through smart dimming
• True On/Off functionality via switched relay
• Seamlessly integrates into the outdoor AirLink wireless lighting control
solution & Self-healing Mesh Networking
• Relay closes on power loss
• Supports a wide range of LED drivers and fixtures
• Class 1 / Class 2 0-10V Dimming Control
• Direct Connect up to two (2) to 24V Occupancy Sensors and
Photocells (consult sales for compatible list)
• Secure, over-the-air upgrades to support future enhancements
• Excellent RF Range — 1,000ft LoS between controllers
• Available in a metal cased version with quick connect
terminal blocks
• Lights default to on for safety
Specifications
Regulatory Approvals
• FCC, IC, CE certified
• cULus Listed
• California Title 24 compliant
Power and Performance
• Operating environmental: -40°F to 131°F (-40°C to 55°C)
• Input power: 100–277 VAC +/- 10% (Max 305V)47/64 Hz
• Switched output: Default ON; Zero Cross Switching
• Load rating: 5A @ 100V to 277V (+/- 10%)
• Dimming: 0–10V control; Output: Class 1/2 - 20mA Source
Max / 50mA Sink Max
• Power monitoring: Utility grade - 2% accuracy
• Sensors inputs: 0–10V (photocell sensors), 0–24V (all other
sensors); Sensor power supply: 24VDC @ 50mA
Other
• Dimensions: 8.2” L x 2.3” W x 1.3” H (209mm L x 59mm W x
33mm H) without antennas
• Radio: SNAP 2.4 GHz; 802.15.4; +20 dBm Transmit Power;
-105 dBm Receive Sensitivity
• Warranty: 5 years
Sales
controls.sales@lsi-industries.com
Support
controls.support@lsi-industries.com
1 (800) 436-7800 (support, option 8)
More information
For more information on AirLink, visit our
website at www.lsi-airlink.com/airlink
Contact LSI Controls
WPLED52N
LED 52W Wallpacks. 3 cutoff options. Patent Pending thermal management system.
100,000 hour L70 lifespan. 5-year, no-compromise warranty.
Color: Bronze Weight: 17.6 lbs
Project:Type:
Prepared By:Date:
Driver Info
Type:Constant Current
120V:0.51A
208V:0.33A
240V:0.29A
277V:0.24A
Input Watts:58W
Efficiency:89%
LED Info
Watts:52W
Color Temp:4000K
Color Accuracy:72 CRI
L70 Lifespan:100000
Lumens:7236
Efficacy:124 LPW
Technical Specifications
Listings
UL Listing:
Suitable for wet locations
DLC Listed:
This product is on the Design Lights Consortium (DLC)
Qualified Products List and is eligible for rebates from
DLC Member Utilities.
DLC Product Code: P00001742
IESNA LM-79 & IESNA LM-80 Testing:
RAB LED luminaires have been tested by an
independent laboratory in accordance with IESNA LM-
79 and 80, and have received the Department of
Energy "Lighting Facts" label
LED Characteristics
Lifespan:
100,000-hour LED lifespan based on IES LM-80
results and TM-21 calculations
LEDs:
Two (2) multi-chip, high-output, long-life LEDs
Color Consistency:
3-step MacAdam Ellipse binning to achieve consistent
fixture-to-fixture color
Color Stability:
LED color temperature is warrantied to shift no more
than 200K in CCT over a 5 year period
Color Uniformity:
RAB's range of CCT (Correlated Color Temperature)
follows the guidelines of the American National
Standard for Specifications for the Chromaticity of
Solid State Lighting (SSL) Products, ANSI C78.377-
2017.
Electrical
Drivers:
Two drivers, constant current, 720mA, Class 2, 100 -
277V, 50 - 60 Hz, 100 - 277VAC .8 Amps.
THD:
6.5% at 120V, 7.8% at 277V
Power Factor:
99.3% at 120V, 97.2% at 277V
Surge Protection:
6kV
Construction
Ambient Temperature:
SuitableFor use in 40°C (104°F) ambient temperatures
Cold Weather Starting:
Minimum starting temperature is -40°C (-40°F)
Housing:
Precision die cast aluminum housing, lens frame
Mounting:
Die-cast aluminum wall bracket with (5) 1/2" conduit
openings with plugs. Two-piece bracket with tether for
ease of installation and wiring.
Arm:
Die-cast aluminum with wiring access plate
Cutoff:
Standard (15°)
Reflector:
Specular vacuum-metallized polycarbonate
Gaskets:
High temperature silicone
Lens:
Tempered glass
Finish:
Formulated for high-durability and long lasting color
Green Technology:
Mercury and UV-free. RoHS compliant components.
Polyester powder coat finish formulated without the
use of VOCs or toxic heavy metals.
Other
Warranty:
RAB warrants that our LED products will be free from
defects in materials and workmanship for a period of
five (5) years from the date of delivery to the end user,
including coverage of light output, color stability, driver
performance and fixture finish.
Patents:
The WPLED design is protected by patents in the U.S.
Pat D653,377, Canada Pat. 142252, China Pat.
ZL201130356930.8, and Mexico Pat. 36921 and
pending patent in TW.
Replacement:
Replaces 250W HID
Need help? Tech help line: (888) RAB-1000 Email: sales@rabweb.com Website: www.rabweb.com
Copyright © 2018 RAB Lighting Inc. All Rights Reserved Note: Specifications are subject to change at any time without notice
Page 1 of 2
W1
52
Building
Exterior
RAB WPLEDFC52N
WPLED52N
Technical Specifications (continued)
Other
Buy American Act Compliance:
RAB values USA manufacturing! Upon request, RAB
may be able to manufacture this product to be
compliant with the Buy American Act (BAA). Please
contact customer service to request a quote for the
product to be made BAA compliant.
Optical
BUG Rating:
B0 U2 G3
Dimensions Features
High performance LED light engine
Maintains 70% of initial lumens at 100,000 hours
Weatherproof high temperature silicone gaskets
Superior heat sinking with die cast aluminum housing and external fins
Replaces 250W MH
Traditional wallpack look from the front
3 cutoff options
5-year, no-compromise warranty
Ordering Matrix
Family Cutoff Wattage Color Temp Finish Driver Options Options
WPLED 52 N
Blank = Standard (15°)
C = Cutoff (7.5°)
FC = Full Cutoff (0°)
80 = 80W
52 = 52W
Blank = 5000K (Cool)
N = 4000K (Neutral)
Y = 3000K (Warm)
Blank = Bronze
W = White
Blank = 120-277V
/480 = 480V
/BL = Bi-Level
/D10 = 0-10V Dimming
Blank = No Option
/PCS = 120V Swivel Photocell
/PCS2 = 277V Swivel Photocell
/PCS4 = 480V Swivel Photocell
/LC = Lightcloud®
Need help? Tech help line: (888) RAB-1000 Email: sales@rabweb.com Website: www.rabweb.com
Copyright © 2018 RAB Lighting Inc. All Rights Reserved Note: Specifications are subject to change at any time without notice
Page 2 of 2
WPLED10N
LED 10W & 13 Wallpacks. Patent Pending thermal management system. 100,000
hour L70 lifespan. 5-year, no-compromise warranty.
Color: Bronze Weight: 3.3 lbs
Project:Type:
Prepared By:Date:
Driver Info
Type:Constant Current
120V:0.1A
208V:0.07A
240V:0.06A
277V:0.05A
Input Watts:12W
Efficiency:82%
LED Info
Watts:10W
Color Temp:4000K
Color Accuracy:83 CRI
L70 Lifespan:100000
Lumens:1208
Efficacy:99 LPW
Technical Specifications
Listings
UL Listing:
Suitable for Wet Locations as a Downlight. Suitable for
Damp Locations as an Uplight. Wall Mount only.
Suitable for Mounting within 4ft. of ground.
Dark Sky Approved:
The International Dark Sky Association has approved
this product as a full cutoff, fully shielded luminaire
IESNA LM-79 & IESNA LM-80 Testing:
RAB LED luminaires have been tested by an
independent laboratory in accordance with IESNA LM-
79 and 80, and have received the Department of
Energy "Lighting Facts" label
LED Characteristics
Lifespan:
100,000-hour LED lifespan based on IES LM-80
results and TM-21 calculations
Color Consistency:
3-step MacAdam Ellipse binning to achieve consistent
fixture-to-fixture color
Color Stability:
LED color temperature is warrantied to shift no more
than 200K in CCT over a 5 year period
Color Uniformity:
RAB's range of CCT (Correlated Color Temperature)
follows the guidelines of the American National
Standard for Specifications for the Chromaticity of
Solid State Lighting (SSL) Products, ANSI C78.377-
2017.
Lumen Maintenance:
The LED will deliver 70% of its initial lumens at
100,000 hours of operation
Construction
Finish:
Formulated for high-durability and long lasting color
Cold Weather Starting:
Minimum starting temperature is -40°C (-40°F)
Maximum Ambient Temperature:
Suitable for use in 40°C (104°F) ambient temperatures
Thermal Management:
Cast aluminum Thermal Management system for
optimal heat sinking. The LPACK is designed for cool
operation, most efficient output and maximum LED life
by minimizing LED junction temperature.
Housing:
Precision die cast aluminum housing, lens frame
Mounting:
Surface plate and Junction box
Green Technology:
Mercury and UV-free. RoHS compliant components.
Polyester powder coat finish formulated without the
use of VOCs or toxic heavy metals.
For use on LEED Buildings:
IDA Dark Sky Approval means that this fixture can be
used to achieve LEED Credits for Light Pollution
Reduction
Gaskets:
High Temperature Silicone
Electrical
Driver:
Multi-chip 10W high output long life LED Driver
Constant Current, Class II, 120V-240V, 50/60/ Hz,
350mA
Other
Patents:
The design of the LPACK is protected by U.S. Pat.
D604,004 and patents pending in Canada, China and
Taiwan.
Patents:
The LPACK design is protected under patents in the
U.S. Pat. D608,040, Canada Pat. 130,243, China Pat.
200930183252.2, and pending patents in Taiwan and
Mexico.
Warranty:
RAB warrants that our LED products will be free from
defects in materials and workmanship for a period of
five (5) years from the date of delivery to the end user,
including coverage of light output, color stability, driver
performance and fixture finish.
Equivalency:
Equivalent to 70W Metal Halide
HID Replacement Range:
Replaces 35-100W Metal Halide
Buy American Act Compliance:
RAB values USA manufacturing! Upon request, RAB
may be able to manufacture this product to be
compliant with the Buy American Act (BAA). Please
contact customer service to request a quote for the
product to be made BAA compliant.
Need help? Tech help line: (888) RAB-1000 Email: sales@rabweb.com Website: www.rabweb.com
Copyright © 2018 RAB Lighting Inc. All Rights Reserved Note: Specifications are subject to change at any time without notice
Page 1 of 2
W2
10
Building
Exterior
RAB WPLED10NS
WPLED10N
Dimensions Features
High performance LED light engine
Maintains 70% of initial lumens at 100,000 hours
Weatherproof high temperature silicone gaskets
Superior heat sinking with die cast aluminum housing and external fins
5-year, no-compromise warranty
Ordering Matrix
Family Wattage Color Temp Sensor Surface Plate Surface Place Finish Photocell
WPLED
10 = 10W
13 = 13W
Blank = 5000K (Cool)
Y = 3000K (Warm)
N = 4000K (Neutral)
Blank = No Sensor
MS = Mini Sensor
Blank = No Surface Plate S = Surface Plate Blank = Bronze
W = White
Blank = No Photocell
/PC = 120V Button
/PCS = 120V Swivel
/PC2 = 277V Button
Need help? Tech help line: (888) RAB-1000 Email: sales@rabweb.com Website: www.rabweb.com
Copyright © 2018 RAB Lighting Inc. All Rights Reserved Note: Specifications are subject to change at any time without notice
Page 2 of 2
FXLED300SFN
Ultra high output, high efficiency LED floodlight with NEMA Types: 7H x 6V, 6H x 4V,
4H x 6V, 5H x 5V and 3H x 3V. Patent Pending airflow technology ensures long LED
and driver lifespan. Use for general and security lighting for large areas, building
facades, signs and landscapes.
Color: Bronze Weight: 66.1 lbs
Project:Type:
Prepared By:Date:
Driver Info
Type:Constant Current
120V:2.65A
208V:1.59A
240V:1.38A
277V:1.17A
Input Watts:316W
Efficiency:95%
LED Info
Watts:300W
Color Temp:4000K
Color Accuracy:82 CRI
L70 Lifespan:100000
Lumens:34800
Efficacy:110 LPW
Technical Specifications
Listings
UL Listing:
Suitable for wet locations. Suitable for ground
mounting.
IESNA LM-79 & LM-80 Testing:
RAB LED luminaries have been tested by an
independent laboratory in accordance with IESNA LM-
79 and LM-80, and have been received the
Department of Energy "Lighting Facts" label
DLC Listed:
This product is on the Design Lights Consortium (DLC)
Qualified Products List and is eligible for rebates from
DLC Member Utilities.
DLC Product Code: P7HRCS9H
Electrical
Drivers:
Constant Current, 1050mA, 50/60 Hz, 120-277V, 4 kV
surge protection, 120V: 2.65A, 208V: 1.59A, 240V:
1.38A, 277V: 1.17A, THD <20%, Power Factor: 99%
THD:
7.0% at 120V, 11.0% at 277V
Optical
NEMA Type:
NEMA Beam Spread of 7H x 6V
LED Characteristics
Lifespan:
100,000-hour LED lifespan based on IES LM-80
results and TM-21 calculations
LEDs:
Multip-chip, high-output, long-life LEDs
Color Consistency:
3-step MacAdam Ellipse binning to achieve consistent
fixture-to-fixture color
Color Stability:
LED color temperature is warrantied to shift no more
than 200K in CCT over a 5 year period
Color Uniformity:
RAB's range of CCT (Correlated Color Temperature)
follows the guidelines of the American National
Standard for Specifications for the Chromaticity of
Solid State Lighting (SSL) Products, ANSI C78.377-
2017.
Construction
IP Rating:
Ingress Protection rating of IP66 for dust and water
Maximum Ambient Temperature:
Suitable for use in 40°C (104°F) ambient temperatures
Effective Projected Area:
EPA = 4
Cold Weather Starting:
Minimum starting temperature is -40°C (-40°F)
Thermal Management:
Superior thermal management with external "Air-Flow"
fins
Lens:
Tempered glass lens
Housing:
Die-cast aluminum housing and door frame
Mounting:
Heavy-duty Slipfitter for 2 3/8"OD pipe
Reflector:
Specular and semi-specular vacuum metalized
polycarbonate
Gaskets:
High-temperature silicone gaskets
Finish:
Formulated for high-durability and long lasting color
Green Technology:
Mercury and UV-free. RoHS compliant components.
Polyester powder coat finish formulated without the
use of VOCs or toxic heavy metals.
Other
Warranty:
RAB warrants that our LED products will be free from
defects in materials and workmanship for a period of
five (5) years from the date of delivery to the end user,
including coverage of light output, color stability, driver
performance and fixture finish.
American Bureau of Shipping (ABS) :
For use on Mobile Offshore Drilling Units (MODU) and
shipping vessels
Replacement:
Replaces 1000W Metal Halide
Need help? Tech help line: (888) RAB-1000 Email: sales@rabweb.com Website: www.rabweb.com
Copyright © 2018 RAB Lighting Inc. All Rights Reserved Note: Specifications are subject to change at any time without notice
Page 1 of 2
RAB FXLED300SFN
Building Exterior,
Above Hangar Doors
W3
300
FXLED300SFN
Technical Specifications (continued)
Other
BAA Compliance:
Click for BAA compliance.
Buy American Act Compliance:
RAB values USA manufacturing! Upon request, RAB
may be able to manufacture this product to be
compliant with the Buy American Act (BAA). Please
contact customer service to request a quote for the
product to be made BAA compliant.
Dimensions Features
300W replaces 1000 MH floodlights
100,000-hour LED lifespan
5-year No Compromise Warranty
Ordering Matrix
Family Wattage Mounting Color Temp NEMA Type Finish Driver Options Options
FXLED 300 SF N
200 = 200W
300 = 300W
SF = Slipfitter
T = Trunnion
Blank = 5000K (Cool)
N = 4000K (Neutral)
Y = 3000K (Warm)
Blank = 7H x 6V
B64 = 6H x 4V
B55 = 5H x 5V
B33 = 3H x 3V
B46 = 4H x 6V
Blank = Bronze
W = White
Blank = 120V
/480 = 480V
/BL = Bi-Level (Slipfitters only)
/D10 = 0-10V Dimming
Blank = No option
/PCS = 120V Swivel
/PCS2 = 277V Swivel
/PCT = 120-277V Twistlock
/PCT4 = 480V Twistlock
/PCS4 = 480V Swivel
/LC = Lightcloud® Controller
Need help? Tech help line: (888) RAB-1000 Email: sales@rabweb.com Website: www.rabweb.com
Copyright © 2018 RAB Lighting Inc. All Rights Reserved Note: Specifications are subject to change at any time without notice
Page 2 of 2