HomeMy WebLinkAboutTR_Tree_Retention_Worksheet_200207.pdfDEPARTMENT OF COMMUNITY
AND ECONOMIC DEVELOPMENT
TREE RETENTION WORKSHEET
Planning Division
1055 South Grady Way-Renton, WA 98057
Phone: 425-430-7200 | www.rentonwa.gov
1.Total number of trees over 6” diameter 1, or alder or cottonwood
trees at least 8” in diameter on project site trees
2.Deductions: Certain trees are excluded from the retention calculation:
Trees that are dangerous 2 trees
Trees in proposed public streets trees
Trees in proposed private access easements/tracts trees
Trees in critical areas3 and buffers trees
Total number of excluded trees: trees
3.Subtract line 2 from line 1:trees
4.Next, to determine the number of trees that must be retained 4, multiply line 3 by:
0.3 in zones RC, R-1, R-4, R-6 or R-8
0.2 in all other residential zones
0.1 in all commercial and industrial zones trees
5.List the number of 6” in diameter, or alder or cottonwood trees
over 8” in diameter that you are proposing5 to retain4:trees
6.Subtract line 5 from line 4 for trees to be replaced:
(if line 6 is zero or less, stop here. No replacement trees are required) trees
7.Multiply line 6 by 12” for number of required replacement inches:inches
8.Proposed size of trees to meet additional planting requirement:
(Minimum 2” caliper trees required for replacement, otherwise enter 0)inches per tree
9.Divide line 7 by line 8 for number of replacement trees 6:
(If remainder is .5 or greater, round up to the next whole number) trees
1 Measured at 4.5’ above grade.
2 A tree certified, in a written report, as dead, terminally diseased, damaged, or otherwise dangerous to persons or property by a licensed
landscape architect, or certified arborist, and approved by the City.
3 Critical areas, such as wetlands, streams, floodplains and protected slopes, are defined in RMC 4-3-050.
4 Count only those trees to be retained outside of critical areas and buffers.
5 The City may require modification of the tree retention plan to ensure retention of the maximum number of trees per RMC 4-4-130H7a.
6 When the required number of protected trees cannot be retained, replacement trees, with at least a two-inch (2") caliper or an evergreen at least
six feet (6') tall, shall be planted. See RMC 4-4-130.H.1.e.(ii) for prohibited types of replacement trees.
1
H:\CED\Data\Forms-Templates\Self-Help Handouts\Planning\Tree Retention Worksheet.docx 08/2015
Minimum Tree Density
A minimum tree density shall be maintained on each residentially zoned lot (exempting single-family
dwellings in R-10 and R-14). The tree density may consist of existing trees, replacement trees, or a
combination.
Detached single-family development 7: Two (2) significant trees 8 for every five thousand (5,000) sq. ft. of lot
area. For example, a lot with 9,600 square feet and a detached single-family house is required to have four (4)
significant trees or their equivalent in caliper inches (one or more trees with a combined diameter of 24”). This
is determined with the following formula:
Multi-family development (attached dwellings): Four (4) significant trees8 for every five thousand (5,000) sq.
ft. of lot area.
Example Tree Density Table:
Lot Lot size Min significant
trees required
New Trees Retained Trees Compliant
1 5,000 2 2 @ 2” caliper 0 Yes
2 10,000 4 0 1 tree (24 caliper
inches)
Yes
3 15,000 6 2 @ 2” caliper 1 Maple – 15
caliper inches
1 Fir – 9 caliper
inches.
Yes
7 Lots developed with detached dwellings in the R-10 and R-14 zoned are exempt from maintaining a minimum number of significant trees onsite,
however they are not exempt from the annual tree removal limits.
8 Or the gross equivalent of caliper inches provided by one (1) or more trees.
2
H:\CED\Data\Forms-Templates\Self-Help Handouts\Planning\Tree Retention Worksheet.docx 08/2015