Loading...
HomeMy WebLinkAboutT-404367Y N w Q 0 N 0 N 00 N 0 am 3 r U) I N LL- n I (N 0 U v L- O U N i I +, N U) C 6 Q / N U) 6 L Q C rn U) N O O') 0 0 0 0 rn C U 6 rn a) 41 3 O U) c 0 C O c a� L L0 / z 0 i— z w ry KEY 1U METAL OR TIMBER POLE 0 2" (IN) x 3/16" (IN) S.S. TETHER WIRE BAND WITH TWO EACH: • 3/8" (IN) - 16 NC x 3/4" (IN) S.S. HEX HEAD BOLT • LOCK WASHERS AND NUTS O3 5116" (IN) EYE AND EYE TURNBUCKLE 25 ® 3/8" (IN) MILD STEEL S-HOOK 0 1/8" (IN) S.S. WIRE ROPE CLAMP (U-BOLT TYPE) 24 © 1/8" (IN) S.S. TETHER WIRE Q7 1 1/2" (IN) BREAKAWAY TETHER ASSEMBLY 21 WITH OPTIONAL EXTENDER BAR ® SIGNAL HEAD ® 6 x 8.2 LB/FT CHANNEL 10 TWO EACH: SPAN WIRE MOUNT MAST ARM MOUNT • 1/2" (IN) - 13 NC x 2 1/2" (IN) S.S. HEX HEAD BOLT INTERNALLY ILLUMINATED SIGN • LOCK WASHERS (DRILL AND TAP POLE MOUNTING DETAILS TO ACCEPT) 11 WIREWAY (SEE DETAIL THIS SHEET) 12 METAL POLE 13 CABINET 14 END BUSHING 15 SEALING LOCKNUT 16 WIRE ROPE THIMBLE 17 CABINET WALL DRILLED 1/8" (IN) OVERSIZE OF NIPPLE 18 CHANNEL DRILLED 1/8" (IN) OVERSIZE OF NIPPLE 19 2" (IN) DIAM. x 4" (IN) NIPPLE (UNLESS OTHERWISE NOTED) 20 POLE WALL DRILLED SO BUSHING WILL PASS THROUGH - HOLE SIZE TO BE A MAXIMUM OF 1/8" (IN) LARGER DIAMETER THAN THE CONDUIT NIPPLE END BUSHING -- INSTALL NIPPLE IN POLE WITH BUSHING INSTALLED 21 6063 EXTRUDED ALUMINUM FRAME BLANK OUT SIGN WITH VISOR 2© LIGHT EMITTING DIODE (LED) BLANK OUT SIGN 23 TRANSLUCENT PLEXIGLASS SIGN FACE - SEE CONTRACT FOR LEGEND 24 1 1/2" (IN) CAST IRON HUB WITH 5/16" (IN) PIN AND COTTER KEY SPAN WIRE MOUNT ASSEMBLY WITH: • 1 1/2" (IN) DIAM. CONDUIT LOCKNUT • 1 1/2" (IN) DIAM. CONDUIT NIPPLE • BRONZE MESSENGER HANGER WITH: - 1/2" (IN) DIAM. J-BOLTS - CABLE LOCK BAR - RIVET COTTER KEY • BRONZE INTERNALLY THREADED WIRE ENTRANCE WITH: - BUSHING INSERT - ALLEN HEAD S.S. SET SCREW 26 ARM MOUNT ASSEMBLY WITH: • 1 1/2" (IN) DIAM. CONDUIT LOCKNUT • BRONZE SERRATED ELL FITTING WITH: - 3/8" (IN) S.S. THROUGH BOLT AND NUTS - THREE S.S. SET SCREWS AT SLIPFITTER CONNECTION - THREE ALLEN HEAD S.S. SET SCREWS AT CONDUIT NIPPLE CONNECTION • 1 1/2" (IN) DIAM. CONDUIT NIPPLE • SERRATED RING WITH NO PINS SIDE POLE MOUNT ASSEMBLY WITH: • 1 1/2" (IN) DIAM. CONDUIT LOCKNUT • 1 1/2" (IN) DIAM. CONDUIT NIPPLE • SERRATED RING WITH NO PINS ® 1 1/2" (IN) SERRATED ELBOW 2�9 1 1/2" (IN) DIAM. NIPPLE (DRILL AND TAP POLE TO ACCEPT) 3a TWO EACH: • 1/2" (IN) - 20 NF x 3/4" (IN) S.S. HEX HEAD BOLT • LOCK WASHERS (DRILL AND TAP POLE TO ACCEPT) 31 MOUNTING BRACKET Q LOCKNUT LEGEND: S.S. = STAINLESS STEEL DRAWN BY: COLBY FLETCHER 26" PLAN VIEW 00 r` CV M NOTES TO METAL OR 0 1. Backplates shall be installed TIMBER POLE 14 with stainless steel screws 8 jjj 19 and stainless steel washers. 1101 ® 2. Silicone top of channel and 18 15 , �° around nipples at openings jjj0 0 17 into pole. 6 10 3. Breakaway tether extender � A ® bar shall extend one hole and one flat past tether wire. TETHER WIRE DETAIL ISOMETRIC VIEW SIDE POLE MOUNT ELEVATION VIEW ISOMETRIC VIEW INTERNALLY ILLUMINATED SIGN MOUNTING DETAILS (n 4 SCOOP FULL CIRCLE c, TUNNEL CAP OR ANGLE CUTOFF 450 SHOWN — SEE VISORS CONTRACT PLANS FOR PERSPECTIVE VIEWS ANGLE AND LENGTH "L" WIREWAY DETAIL ISOMETRIC VIEW 4 SECTION O ELEVATION VIEW CABINET MOUNTING DETAILS RETRO-REFLECTIVI YELLOW TAPE — SEI STD. SPEC. 9-29.11 BACKPLATE DETAIL 8" (IN) OR 12" (IN) SECTIONS 8" (IN) SECTION X = 5 1/2" (IN) t 1/2" (IN) 12" (IN) SECTION X = 5 1/2" (IN) t 1/2" (IN) MISCELLANEOUS SIGNAL DETAILS STANDARD PLAN J-75.30-02 SHEET 1 OF 1 SHEET APPROVED FOR PUBLICATION Carpenter, Jeff Jul 10 2015 7:17 AM ' STATE DESIGN ENGINEER cosi i► T Washington State Department of Transportation T-404367 • U V � <Y w w O z z w o z J z O N 2 I LL. N C9 QLLI Z L;.i � U Q i a 0 0 U Q 0 a a Q L LI a z 0 E o > CO N of m a N z O IN� O U LU LL N j v 0S ' O U) f6 m W w N W 0 m m w Y U W U ?N O z V z U zR Q Z F Z LU Z = 3 LL = Cl) LU W = ? O J F- LU o z O_ U LL Cl) LL ~ U z O U 0 W Z LU ' Q 0 J Q z Y Z O Z LU SHEET:63/SIG-19 OF: 70 JOB NO.: 17534 DWG: DETS-PDFS-SH 37