HomeMy WebLinkAboutT-408305CM
00
0
T
I
O
IZ
I —
DIVISION 26 -ELECTRICAL SPECIFICATIONS
1. GENERAL CONDITIONS:
A. THE GENERAL CONDITIONS, SUPPLEMENTARY CONDITIONS AND SPECIAL
CONDITIONS ARE A PART OF THIS CONTRACT AND APPLY TO THIS SECTION
AS FULLY AS IF REPEATED HEREIN.
n e+i+0%nr__
A. THIS SECTION OF SPECIFICATIONS INCLUDES, BUT IS NOT LIMITED TO:
ALL LABOR, TOOLS, APPLIANCES, MATERIALS AND EQUIPMENT REQUIRED TO
FURNISH AND INSTALL THE COMPLETE INSTALLATION SHOWN ON THE
DRAWINGS FOR THIS SECTION OF THE WORK AND/OR IN THE FOLLOWING
SPECIFICATIONS, INCLUDING THAT WHICH IS REASONABLY INFERRED.
3. CODES AND REGULATIONS:
A. ALL WORK AND MATERIALS SHALL BE IN ACCORDANCE WITH APPLICABLE
REQUIREMENTS OF PUBLIC AUTHORITIES HAVING JURISDICTION AND UTILITIES
FURNISHING SERVICES.
B. CODES GOVERNING THIS WORK INCLUDE BUT ARE NOT LIMITED TO THE
LATEST APPROVED EDITION OF THE FOLLOWING:
NATIONAL FIRE PROTECTION ASSOCIATION'S NATIONAL ELECTRICAL
CODE (NEC).
OCCUPATIONAL SAFETY AND HEALTH ACT (OSHA).
LOCAL ORDINANCES AND REGULATIONS. CITY OF RENTON STANDARDS.
4. STANDARDS:
A. ELECTRICAL MATERIAL AND EQUIPMENT SHALL HAVE BEEN TESTED AND
LISTED OR LABELED AS CONFORMING TO APPROVED PUBLISHED STANDARDS
BY UNDERWRITERS LABORATORIES WHERE SUCH LISTING OR LABELING
SERVICE IS AVAILABLE FOR THE CLASS OF MATERIALS OR EQUIPMENT.
WHERE APPLICABLE, LISTING OR LABELING SHALL APPLY TO THE COMPLETE
ASSEMBLED EQUIPMENT AND NOT TO THE COMPONENTS ALONE.
5. SUBMITTALS:
A. THREE COPIES OF MATERIALS LIST, SHOP DRAWINGS AND DATA SHEETS
SHALL BE SUBMITTED TO ARCHITECT &/OR CONSTRUCTION MANAGER FOR
REVIEW. SUBMITTALS SHALL BE MADE AND FAVORABLE REVIEW SECURED
BEFORE MATERIAL AND EQUIPMENT IS INSTALLED.
B. MATERIALS LIST SHALL INCLUDE FIXTURES, PANELS, DEVICES,
WIREWAYS, DISCONNECTS, AND ALL OTHER SPECIFIED OR UNSPECIFIED
STANDARD CATALOGED MATERIALS TO BE USED. THE LIST SHALL INCLUDE
MANUFACTURER, TYPE AND SUCH OTHER DESCRIPTIVE DATA AS MAY BE
REQUIRED TO DETERMINE THE ACCEPTABILITY OF EACH ITEM.
C. SHOP DRAWINGS AND DATA SHEETS FOR EQUIPMENT AND SYSTEMS SHALL
BE SUBMITTED WHERE REQUIRED IN THE SPECIFICATION FOR THOSE ITEMS.
INCLUDE INFORMATION ON EACH COMPONENT, WIRING DIAGRAMS, LAYOUTS,
DIMENSIONS AND SUFFICIENT OTHER DATA TO ESTABLISH COMPLIANCE WITH
THE SPECIFICATIONS AND ACCEPTABILITY OF THE EQUIPMENT OR SYSTEM.
6. PERMITS AND DRAWINGS:
A. ELECTRICAL CONTRACTOR SHALL SUBMIT TO THE LOCAL AUTHORITY THE
REQUIRED DOCUMENTS TO PURCHASE AND SECURE ALL NECESSARY PERMITS
AND COORDINATE REQUIRED INSPECTIONS FOR APPROVAL.
7. AS -BUILT DRAWINGS:
A. ON A SET OF CONTRACT DRAWINGS, KEPT AT THE SITE DURING
CONSTRUCTION, MARK ALL WORK THAT IS INSTALLED DIFFERENTLY FROM
THAT SHOWN, INCLUDING ANY REVISED CIRCUITRY, MATERIAL OR
EQUIPMENT. UPON CONCLUSION OF WORK, DELIVER TO OWNER'S REP.
CONSTRUCTION MANAGER A SET OF SIGNED AND DATED "AS -BUILT"
DRAWINGS.
8. GUARANTEE:
Abossein
Engineering,
L.L.C.
A. ALL WORK SHALL BE GUARANTEED FOR A MINIMUM PERIOD OF ONE YEAR
FROM THE DATE OF ACCEPTANCE BY THE OWNER. THE GUARANTEE PERIOD
FOR CERTAIN ITEMS SHALL BE LONGER, AS INDICATED IN THE
SPECIFICATION FOR THOSE ITEMS.
B. SHOULD ANY MALFUNCTION DEVELOP DURING THE GUARANTEE TIME PERIOD
DUE TO DEFECTIVE MATERIAL, FAULTY WORKMANSHIP, OR NON-COMPLIANCE
WITH PLANS, SPECIFICATIONS, CODES OR DIRECTIONS OF THE OWNER,
ARCHITECT, ENGINEER OR INSPECTOR, THE CONTRACTOR SHALL FURNISH
ALL NECESSARY LABOR AND MATERIALS TO CORRECT THE MALFUNCTION
WITHOUT ADDITIONAL CHARGES.
MECHANICAL - ELECTRICAL
CIVIL - LEED
FIRE PROTECTION
18465 NE 68TH ST
REDMOIND, WA. 98052
PH: (425) 462-9441
FAX: (425) 462-9451
E-Mail: cservice@abossein.com
www.abossein.com
ABOSSEIN #21901
r% P9 A 111 1 ^.r ^
3. INSTALLATION AND CONNECTION OF WIRING:
A. CLEAN OUT AND DRY ALL CONDUIT AND WIREWAYS BEFORE PULLING ANY
WIRES. USE NO LUBRICANT EXCEPT AS RECOMMENDED BY THE WIRE OR
CABLE MANUFACTURER.
B. MAKE ALL CONNECTIONS AND SPLICES NECESSARY TO PROPERLY COMPLETE
THE ELECTRICAL WIRING. CONNECTIONS AND SPLICES SHALL BE MADE
ONLY IN PULL AND JUNCTION BOXES. ALL SPLICES SHALL BE MADE WITH
UL LISTED UG TYPE EPDXY.
2. INSTALLATION OF CONDUIT:
A. STANDARD WEIGHT RIGID METAL CONDUIT SHALL BE USED WHERE EXPOSED
TO THE WEATHER, PLACED UNDERGROUND BELOW CONCRETE SLAB, IN
CONCRETE OR MASONRY CONSTRUCTION IN CONTACT WITH EARTH, AND
WHERE SHOWN ON THE PLANS.
B. GALVANIZED STEEL ELECTRICAL METALLIC TUBING SHALL BE USED IN ABOVE
GROUND, INTERIOR, DRY LOCATIONS PROTECTED FROM WEATHER AND
PHYSICAL DAMAGE, AND MAY BE USED IN CONCRETE OR MASONRY
CONSTRUCTION NOT IN CONTACT WITH EARTH.
10. UNDERGROUND STREET LIGHT JUNCTION BOXES:
11. CONDUITS AND FITTINGS:
A. STANDARD WEIGHT RIGID METAL CONDUIT SHALL BE HOT DIPPED
GALVANIZED, ALL FITTINGS SHALL BE OF THE SCREW THREAD TYPE.
COUPLINGS, LOCKNUTS, BUSHINGS, ETC., SHALL BE HOT DIPPED
GALVANIZED.
B. RIGID NON-METALLIC CONDUIT SHALL BE PVC SCHEDULE 40, U.L.
APPROVED. SCHEDULE 80 FOR STREET CROSSINGS. ALL COUPLINGS,
FITTINGS, SOLVENT CEMENT, ETC..
12. WIRE AND CABLE:
A. WIRE AND CABLE FOR USE ON SYSTEMS OF 50 VOLTS TO 600 VOLTS
SHALL BE 600 VOLT RATED TYPE THW OR THHN FOR BRANCH CIRCUITS.
FEEDERS SHALL BE THHN OR THWN (SEE RISER).
B. WIRE AND CABLE FOR USE ON SYSTEMS OF BELOW 50 VOLTS SHALL BE
300 VOLT PVC INSULATED AND SUITABLE FOR THE CLASS OF WIRING
EXCEPT AS OTHERWISE INDICATED OR SPECIFIED.
C. ALL CONDUCTORS SHALL BE COPPER, RATED 75°C MINIMUM.
D. ALL WIRING TO BE COLOR CODED AS FOLLOWS:
208/120V 480/277V
PHASE A - BLACK PHASE A - BROWN
PHASE B - RED PHASE B - ORANGE
PHASE C - BLUE PHASE C - YELLOW
NEUTRAL - WHITE NEUTRAL - WHITE/TRACER OR GREY
`9j"M:kIILl Eel aL 01fl*5
A. FIXTURES SHALL BE COMPLETE WITH ALL REQUIRED ACCESSORIES AND
EQUIPMENT, INCLUDING LAMPS, NECESSARY FOR A COMPLETE INSTALLATION.
CONTRACTOR SHALL RECEIVE, UNPACK, ASSEMBLE AND INSTALL FIXTURES
AS NOTED ON DRAWINGS.
14. NAMEPLATES AND LABELS:
A. NAMEPLATES SHALL BE PROVIDED TO IDENTIFY EACH LIGHT POLE AND
SIMILAR ITEMS WHICH ARE FURNISHED OR INSTALLED UNDER THIS SECTION
AS REQUIRED BY CITY OF RENTON STANDARDS.
B. NAMEPLATES SHALL BE ENGRAVED LAMINATED PLASTIC WITH CHARACTERS
CUT THROUGH THE BLACK TOP LAYER TO WHITE LAYER BELOW.
BASE MAP/TOPOGRAPHY PROVIDED BY
A8�
OTHERS. DCG CANNOT BE HELD LIABLE
WA
FOR ACCURACY. CONTRACTOR SHALL
FIELD VERIFY GRADES, UTILITIES AND
ALL OTHER EX FEATURES &
�21891
NDITIONS. IF CONDITIONS ARE NOT
�SS�ONALEN�\
AS SHOWN &/OR PLANS CANNOT BE
CONSTRUCTED AS SHOWN, CONTACT
S— ZD
DCG PRIOR TO CONSTRUCTION.
rVr^1 ITI/1\1
1. INSTALLATION AND CONNECTION OF ELECTRICAL
EQUIPMENT:
A. EQUIPMENT SHALL BE COMPLETELY CONNECTED TO THE ELECTRICAL SYSTEM
AS NOTED ON DRAWINGS AND PER MANUFACTURER INSTALLATION
REQUIREMENTS.
B. RIGID NON-METALLIC CONDUIT MAY BE USED FOR ALL UNDERSLAB OR
UNDERGROUND WORK IN PLACE OF STANDARD WEIGHT RIGID METAL AND
WHERE SPECIFICALLY SPECIFIED. ALL RUNS OF RIGID NON-METALLIC
CONDUIT SHALL CONTAIN A SEPARATE GREEN GROUND WIRE ADEQUATELY
SIZED FOR SERVICE INTENDED. WHERE REQUIRED TO CONTINUE ABOVE
SLAB, STUB NON-METALLIC CONDUIT 6" ABOVE SLAB THEN MAKE PROPER
TRANSITION TO METAL CONDUIT.
C. ALL RIGID STEEL CONDUIT INSTALLED IN THE GROUND SHALL BE WRAPPED
WITH HUNT'S PROCESS NO. 3, PVC COATED OR ENCASED IN 3" CONCRETE
ON ALL SIDES.
D. THE MINIMUM SIZES OF CONDUIT SHALL BE CODE SIZE FOR THE NUMBER
AND SIZE OF CONDUCTORS, UNLESS A LARGER SIZE IS SHOWN, IN WHICH
CASE SUCH LARGER SIZE SHALL BE USED.
G. THE MINIMUM SIZES OF CONDUIT SHALL BE CODE SIZE FOR THE NUMBER
AND SIZE OF CONDUCTORS, UNLESS A LARGER SIZE IS SHOWN, IN WHICH
CASE SUCH LARGER SIZE SHALL BE USED.
4. GROUNDING:
A. MAKE GOOD MECHANICAL AND ELECTRICAL CONTACT AT ALL POLES,
JUNCTION BOXES, AND WHEREVER THE CONDUIT RUN IS CONNECTED.
PERMANENTLY AND EFFECTIVELY GROUND ALL CONDUIT, FIXTURES, AND
OTHER EQUIPMENT AS REQUIRED BY ALL APPLICABLE CODES, REGULATIONS
AND STANDARDS. NEC 250. REFER TO J013 CITY OF RENTON STANDARD
GROUNDING DETAIL.
5. CLEANING AND PROTECTION OF
PRODUCTS AND PREMISES:
A. AT FREQUENT INTERVALS DURING THE TIME OF CONSTRUCTION, THE
CONTRACTOR SHALL CLEAN UP AFTER HIS WORK AND REMOVE HIS DEBRIS
FROM THE PREMISES, LEAVING THE BUILDING AND GROUNDS CLEAN TO THE
OWNER'S SATISFACTION.
B. THE CONTRACTOR SHALL TAKE ALL NECESSARY PRECAUTIONS TO
PROTECT ALL MATERIALS, EQUIPMENT AND PROPERTY, WHETHER ELECTRICAL
OR NOT, FROM DAMAGE AS A RESULT OF HIS WORK.
6. CHECKING AND TESTING OF
EQUIPMENT AND SYSTEMS:
A. SYSTEMS SHALL BE TESTED FOR SHORT CIRCUITS, OPEN CIRCUITS AND
WRONG CONNECTIONS AND SHALL BE FREE FROM MECHANICAL AND
ELECTRICAL DEFECTS. CIRCUITS SHALL BE TESTED FOR PROPER NEUTRAL
AND GROUND CONNECTIONS.
9. TEMPORARY CONSTRUCTION POWER & TELEPHONE:
A. ELECTRICAL CONTRACTOR SHALL PROVIDE ALL LABOR, COST AND
MATERIALS REQUIRED FOR INSTALLATION AND MAINTENANCE OF TEMPORARY
CONSTRUCTION POWER AND TELEPHONE AS NECESSARY FOR PROJECT
COMPLETION.
PERMIT SUBMITTAL 03-13-19 SURVEYED: SCALE:
VERTICAL: NAVD 1988
PERMIT SUBMITTAL WITH CIVIL CHANGES 08-05-19 DESIGNED: AS NOTED HORIZONTAL: NAD 1983/1991
PERMIT SUBMITTAL CITY COMMENTS 02-05-19 JBw
DRAWN:
ONE INCH DATUM
CHECKED: AT FULL SCALE
AA IF NOT ONE INCH
N 0. REVISION BY DATE APPF APPROVED: SCALE ACCORDINGLY
CITY OF RENTON STANDARD
Conduit, Innerduct, and Outerduct
The conduit PVC - non-metallic shall be of the two types indicated below:
1. Schedule 80 Extra heavy wall PVC conforming to ASTM, Standards, to be used in all
installations under roadways.
2. Schedule 40 heavy wall PVC conforming to ASTM Standards.
Standard Duty Junction Boxes
Junction boxes shall be reinforced concrete with galvanized steel frame anchored in place and
galvanized steel cover plate (Diamond pattern). Grounding lugs shall be stainless steel and shall be
mechanically and electrically bonded. Junction boxes for copper wire shall incorporate a locking lid per
City of Renton Standard Plan. Junction boxes placed in the sidewalks shall have non-skid lids.
Luminaires
Roadway and pedestrian luminaires shall be LED type, wattages similar to the wattages shown in the
luminaire schedules on the Plans. The Contractor shall be responsible for verifying that the
performance of the LED luminaires is adequate to comply with the City illumination standards
without modifying illumination and signal pole locations shown on the Plans. IES files shall be
provided, by the Contractor upon the request, by the Engineer.
Optical assembly/reflector shall be made of pre -anodized aluminum, segmented in multiple facets,
ventilated perforations and heat sinks to maximize heat dissipation. Reflector shall produce full
cut-off Type IV optics to meet the design/performance criteria, 4000K CCT. LED driver module rated
for 120V-277V operation, high power factor (90%), with a minimum starting temperature of -40
Degrees Fahrenheit, secured on a tool less access tray with quick disconnects. Individual LED chips or
modules shall be removable by means of tool less access in the event they need to be replaced. LED
driver not to exceed 750 MA.
All fixtures shall be of the some manufacturer and external appearance.
Color shall use paint code RAL9005TX
Follow standard 121 for street lighting identification numbers. Obtain pole number scheme from
Transportation Maintenance Manager Eric Cutsholl 425-430-7423.
Photoelectric Controls
Photoelectric controls shall be a plug-in device, rated to operate on 120 volts, 60 Hz. The unit shall
consist of a light sensitive element connected to necessary control relays. The unit shall be so
designed that a failure of any electronic component will energize the lighting circuit.
M1
co
N
O
CD
CD
00
T
a
J
The photo cell shall be a solid state device with stable turn_on values in the temperature range of C)
-55 degrees C to +70 degrees C. In a contactor controlled system, the photo cell to control the (.0
system shall be mounted on the luminaire nearest to the service/contactor cabinet. The photo cell T
shall be rated as a 10-year (or higher) life expectancy. CD
O
O
I
T
0-
U
IZ
E)
U
J
T-408305
U)
0
U
IN COMPLIANCE WITH CITY OF RENTON
STANDARDS
W
DEVELOPMENT ENGINEERING
Z
W
CALL 811 (2) BUSINESS DAYS
Nathan Janders 03/19/2020
BEFORE YOU DIG
z
Q
(UNDERGROUND UTILITY
CURRENT PLANNING ��
z
LOCATIONS ARE APPROXIMATE)
Angelea Weihs 07/23/2019
Q
C TY OF
FIRST UKRAINIAN PENTECOSTAL CHURCH
DATE:
2/14/20
cc
�e
FIELDBOOK:
PAGE:
[;R RENTON
3811 NE21STST
1421V
RENTON, WA 98056
DRAWING NO:
Planning/Building/Public works Dept.
STREET LIGHTING SPECIFICATIONS
ESL4.0
Cr
SHEET: 41 OF: 65
ILL