HomeMy WebLinkAboutR-417972PACIFIC OUTDOOR
P R O D U C T S, I N C.
PE-7885
Area needed: 28' x 28'
Ages 5_12 years
Capacity 20-28
Activities 5
ADA
Access
16".. ADA
Barrier Pipes Access Spider
24` Climber
Barracuda 40" Barrier
Climber 40" Pipes
R 5' Craw
Tunnel
Bubble Pyramid
Panel
Roof
s Banana
Slide
DETAIL: PE-7885 (A)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
DETAIL: BALANCE BEAM (C)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
DETAIL: PULL UPS (G)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
Q
N
O
N
N
N
PACIFIC OUTDOOR
P R O D U C T S, I N C.
PE-7875
Area needed: 18'x22'
Ages 2-12
Capacity 12-16
Activities 4
Barracuda
Climber
Pyramid
Roof
Snake
ipe Wall
Climber/
0A.A
Wheel
Activity
PanelAco..
ADA
Access
DETAIL: PE-7875 (B)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
DETAIL: FE-1310 BENCH (D)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
DETAIL: SPRING ANIMAL (J)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
UNDERGROUND LOCATOR SERVICE
C% L L BEFORE YOU DIC.1
8/7
1 I CONSTRUCTION RECORD DRAWINGS
NO. I REVISION
PACIFIC OUTDOOR
PRO DUCTS, INC.
PE - 2024 Single Bay Steel Swing
Safe Use Area Needed 28' x 32'
16'
' Ta I I
12" Ground Cover
30" In Ground
DETAIL: PE-2024 (H)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
DETAIL: VERTICAL KNEE RAISE (E)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
SE-5165 Bench Specifications
Material:
Boards 2 x 4, all edges eased
Steel legs 2" x 2" square tube with
3/8" x 4" flat for seat and back brace,
all welded and powder coated
" 5/16" x I %' lags & washers
M.-I,
Mountng: Surface mount or in -ground
Boards:2 x 4 Poly (recycled plastic) or wood
Length: 71"standard
18" IB"
16 16" 6
33" �19' Ig"
Sudace M.—Plate
Ig" g
� mmen
16
In -Ground
31 Install the bench frames approxlmately lg" In the ground, 2 frames fora timber bench and 3 frames for a
Poly bench, the third frame is centered between the two outer frames. Level the frames by Putting one of
the 2x4 bench boards on the frames and using a level to ,it, sure the board Is level. lags the boards on,
from the bottom of the frames. Make sure the frames are "plumb and level"
2) Pourtheconcrete lntheholessoltisnomorethan2"fromthetopofeachhole.Onceithascuredupyou
in lag bolt the boards to the bench frames. Make sure the top of the seat bench boards is approximately
18" above the finished grade.
3) The bench boards are to be centered on the predrilled holes in the bench frames. The timber boards
ove
rhang each edge 12" and the poly boards overhang 6" on each edge spaced equally open.
4) In the poly bench boards,it is necessary to drill a 3/16" pilot hole for each lag before bolting the bench
together.
Surface Mount
1) Assemble the bench by lagging the boards onto the frames. The timber bench frames over hang each
bench frame 12" and the poly boards overhang the frames V. Center the boards on the predrilled holes
in the frames, space evenly and lag bout them together. Leg them on from the bottom of the frames.
2) Once the bench is assembled place it on the concrete where it is to be installed and mark where the
rinountini hales are to be drilled on the concrete. Remove the bench and drill the holes and bolt the
be..hdown.
31 In the poly bench boards, it is necessary to drill a 3/16" Allot hole for each lag before hotting the bench
together. l PACIFIC OUTDOOR
P R O D U C T S, I N C.
"NOTE: Graphics are not to scale." %mv,cloaclflcoutdoor.com
DETAIL: BENCH
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
M E M 2/ 1 3/24 T H H SURVEYED: SCALE:
GLENN R SPRAGUE P. L. S.
DESIGNEDSHAHLA HOWEV
BY I DATE I APPR
DRAWN:
JAC06 REEEE
CHECKED:
L INOSE Y SOL ORIO
APPROVED:
INDSEY 5 SOL OR/0 P. L.
ONE INCH
AT FULL SCALE
IF NOT ONE INCH
SCALE ACCORDINGLY
PACIFIC OUTDOOR
P R O D U C T S, I N C.
PE-7750A
4x6 Poly Playsyslem
Safe play area needed: 30' x 32'
Designed for ages: 5 - 12 years
Meets ASTM, ADA and CPSC Safety Guidelines
6' Glide
Slide
6'Banana
Slide
Pyramid
Roof
Angled Rock
40"
Climber
U-Bend
32..
Activity
Climber
Panel
Step
6"
Deck
Pipe
ADA
Wall
24
16"
Access
Steering
Wheel
ADA
Window
Pipe Wall
Access
Panel
DETAIL: PE-7750 (1)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
DETAIL: LEG RAISE (F)
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
SE-5335 Table Specifications
Material:
11/2" x 9112" Poly or Wood boards
2" x 2" welded steel frame
4" x 4" center table support
All steel is welded together and powder
sated.
5/16" x 1 -' lags and washers
Obti n
Mounting: Surface mount or in -ground
ea"
J 1a g l
Surface Maun[ PIMe
28" in 9rountl
16"
In Ground Installation
1) Place the table where you want to Install it and mark the ground.
2) Dig l6"diameter x 28" deep hole and place the table In the hole making sure the seats are
approximately 17" to 19" off the ground.
3) Make sure the table is"plumb and level" in the hole. Fill the hole with pre -mix concrete leaving
2" from the top of the hole.
4) Once the concrete has hardened place the to ble boa rds evenly on the frame and lag them to the
frame from the bottom into the board.
5) If the table boards are poly you need to drill a 3/16" pilot hole in each board prior to lagging the
board to the frame.
Surface Mount
1) Set on the concrete where It is to be installed and mark where the mounting holes are to be
drilled on the concrete through the mounting plate.
2) Remove the table, drill the holes, with a S/8" concrete drill bit.
3) Place the table back on the marks and tighten the anchor bolts.
PACIFIC OUTDOOR
"NOTE: Graphics are not to scale. " PR O D U CT S, I N C.
www.pacif coutdooccom
NOTE:
ADA OPTION IS OFFERED BY PACIFIC OUTDOOR PRODUCTS.
DETAIL: PICNIC TABLE
SOURCE: PACIFIC OUTDOOR PRODUCTS NOT TO SCALE
CIVIL ENGINEERING
LANDSCAPE ARCHITECTURE
PLANNING
SURVEYING
Bothell, Washington 98077 425.885.7877
R-417972
IN COMPLIANCE WITH CITY OF RENTON STANDARDS
DATE:
VERTICAL: NAVD 1988 • CANOPY
HORIZONTAL: NAD 1983/1991 0 T Y OF
2115124
4196 LINCOLNAVENE, RENTON, WA 98056
Ul
FIELDBOOK:
RENTON PAGE:
DATU M LANDSCAPE DETAILS DRAWING NO: Planning/Building/Public Works Dept. L2.32
SHEET: OF:
84 107
CONSTRUCT/ON RECORD DRA WINGS
O
Z
Q