Press Alt + R to read the document text or Alt + P to download or print.
This document contains no pages.
HomeMy WebLinkAbout5.31.22 - Solera - Utility Submittal Package_KPFF Water ONLYNelson & Sons
Water System
Solera #21089
Solera
Summary of Specifications Provided
McWayne Ductile – Water Line – P. 3-7
Star Pipe – DI Fittings, Valve Cans, Pipe Restraints – P. 8-13
U.S Pipe – DI Spools, Galvanized Spools – P. 14
Romac – Romac Coupler, Romac Restraints – P. 15-17
Sigma – Poly Wrap for DI Pipe, Meter Boxes – P. 18-19
Clow – Gate Valves, Hydrants – P. 20-22
Harrington – STORZ Adapter – P.23
Standon – Pipe Supports – P. 24
JMF- Copper – P. 25
Ford Meter Box – Irrigation Service Material – P. 27-28
Merit Brass – Brass Nipples, Brass Fittings – P. 29
Lansdale – Post Indicator, All thread, Bolt, Tamper Switch – P. 30-36
ITP – Flange Gaskets – P. 47
Apollo – Double Check – 38-39
OMNI – 3” Meter – P. 40-41
Old Castle Infrastructure – Meter Vault – P. 42-43
Garlock – Link Seals – P. 44
Boltless restrained joint systems • Multiple design options available from 3”–36” • Fast and easy installation • 350 psi pressure rating • Independently tested
mcwaneductile.com
MCWANE DUCTILEIRON PIPE
DI Cement Line Pipe
APPLICATION NOTES
1. For ductile iron applications utilizing TYTON® pipe, vales, and fittings made to
AWWA specifications.
2. In cold weather assembly maintain the temperature of the gasket above 40° F.
3. The socket of the joint should be clean and free of debris or significant corrosion.
4. Gasket should be properly seated in the bell socket.
5. Keep the pipe and joint in alignment during assembly. If installed out of alignment, the gasket can be pushed out of position, creating the potential for leaks or failure.
6. If deflection is wanted in the joint, deflect before fully inserting the joint.
7. Some extension of the joint will occur when pressurized. To avoid this, the joint
should be pulled out after assembly to “set” the stainless steel teeth in the
inserted pipe.
8. Once assembled, the joint can be disassembled using steel shims.
9. When cut pipe is used, the following steps are required:
a. Ensure that the spigot end is properly beveled
b. Mark the joint depth on the spigot so it is clear when the joint is fully inserted.
c. Ensure that the pipe meets the required dimensional tolerances.
10. Do not reuse SURE STOP 350® GASKETS, as they may have been damaged during
any previous installation or during removal.
11. Do not use SURE STOP 350® GASKETS to conduct electricity through the pipe
joint, as they could be damaged and fail.
12. Do not use SURE STOP 350® GASKETS in above ground applications.
13. Do not use SURE STOP 350® GASKETS with thick coating on the pipe exterior.
14. If SURE STOP 350® GASKETS are used in straight casings, you must pull the pipe
through the casing. Do not push the pipe.
Size In.Rating psi Deflection Degrees
3 350 5
4 350 5
6 350 583505
10 350 5
12 350 5
14 350 4
16 350 4
18 350 4
20 350 2.5
24 350 2.5
SURE STOP® GASKET FOR TYTON® JOINT
PUSH-ON JOINT PIPE Maximum Allowable Joint Deflection
Pipe SizeIn.
Y-Maximum Joint Deflection in Degrees
X Deflection in Inches 18 ft. Length
Approximate Radius in ft. of Curve Produced by Succession of Joints 18 ft. Length
3 5°19 205
4 5°19 205
6 5°19 205
8 5°19 205
10 5°19 205
12 5°19 205
14 5°19 205
16 5°19 205
18 5°19 205
20 5°19 205
24 5°19 205
30 5°19 205
36 4°15 260
JOINT DEFLECTION CHART
MECHANICAL JOINT PIPE Maximum Allowable Joint Deflection
Pipe Size In.
Y-Maximum Joint Deflection in Degrees
X Deflection in Inches 18 ft. Length
Approximate Radius in ft. of Curve Produced by Succession of Joints 18 ft. Length
6 7°–7’27 145
8 5°–21’20 195
10 5°–21’20 195
12 5°–21’20 195
14 3°–35’13.5 285
16 3°–35’13.5 285
18 3°–0’11 340
20 3°–0’11 340
24 2°–23’9 450
MAXIMUM DEFLECTION FOR FULL LENGTH PIPE
SURE STOP 350® GASKETS are available in sizes 3 in. – 24 in., and with a rating of 350 psi they will meet or exceed the capabilities of ductile iron pipe, valves, and fittings.
SURE STOP 350® GASKETS are NSF 61 approved, UL listed, and FM approved. FM Rating: 4 in. –6 in. = 250 psi 18 in. –24 in. = 200 psi
mcwaneductile.com
Pipe Size
In.
Min. Pipe
Diameter In.
Max. Pipe
Diameter In.
Min. Pipe
Circumference In.
Max. Pipe
Circumference In.
3 3.9 4.02 12-1/4 12-5/8
4 4.74 4.86 14-29/32 15-9/32
6 6.84 6.96 21-1/2 21-7/8
8 8.99 9.11 28-1/4 28-5/8
10 11.04 11.16 34-11/16 35-1/16
12 13.14 13.26 41-9/32 41-21/32
14 15.22 15.35 47-13/16 48-7/32
16 17.32 17.45 54-13/32 54-13/16
18 19.42 19.55 61 61-13/32
20 21.52 21.65 67-19/32 68
24 25.72 25.85 80-13/16 81-7/32
30 31.94 32.08 100-11/32 100-25/32
36 38.24 38.38 120-1/8 120-9/16
Above Table Based on ANSI/AWWA C151/A21.51 Guidelines for Push-On Joints.
FIELD CUT PIPEWhen pipe is cut in the field, the cut end may
be readily conditioned so that it can be used to
make up the next joint. The outside of the cut end should be beveled about 1/4 –inch at an
angle of about 30 degrees (Figure 1). This can be quite easily done with a coarse file or a portable
grinder. The operation removes any sharp, rough
edges which otherwise might damage the gasket.
When ductile iron pipe 14 in. and larger is to be cut in the field, the material should
be ordered as “GAUGED FULL LENGTH”. Pipe that is “gauged full length” is specially marked to avoid confusion. The ANSI/AWWA standard for ductile iron pipe requires
factory gauging of the spigot end. Accordingly, pipe selected for field cutting should also be field gauged in the location of the cut and found to be within the tolerances
shown in Table 1. In the field, a mechanical joint gland can be used as a gauging device.
THE BACKHOE METHOD OF ASSEMBLY
A backhoe may be used to assemble pipe of intermediate and larger sizes. The plain end of the pipe should be carefully guided by hand into the bell of the
previously assembled pipe. The bucket of the backhoe may then be used to push the pipe until fully seated. A timber header should be used between the pipe and
backhoe bucket to avoid damage to the pipe.
TABLE 1: SUITABLE PIPE DIAMETERS FOR FIELD CUTS AND RESTRAINED JOINT
FIELD FABRICATION
Figure 1
DI Cement Lined Pipe
TYTON® JOINT PIPE
Pipe Size In.
PressureClasspsi
NominalThicknessIn.
OD* In.
Wt. of BarrelPer Ft. † Lb.
Tyton® Joint
Wt. of
Bell Lb.
Wt. Per Lgth.† Lb.
Avg. Wt. Per Ft.‡ Lb.3 350 0.25 3.96 8.90 7.00 185 9.2043500.25 4.80 10.90 9.00 225 11.30
6 350 0.25 6.90 16.00 11.00 300 16.60
8 350 0.25 9.05 21.10 17.00 395 22.00
10 350 0.26 11.10 27.10 24.00 510 28.40
12 350 0.28 13.20 34.80 29.00 655 36.40
14
250 0.28 15.30 40.40 45.00 770 42.90
300 0.30 15.30 43.30 45.00 825 45.803500.31 15.30 44.70 45.00 850 47.20
16
250 0.30 17.40 49.30 54.00 940 52.30
300 0.32 17.40 52.50 54.00 1000 55.50
350 0.34 17.40 55.80 54.00 1060 58.80
18
250 0.31 19.50 57.20 59.00 1090 60.50
300 0.34 19.50 62.60 59.00 1185 65.90
350 0.36 19.50 66.20 59.00 1250 69.50
20
250 0.33 21.60 67.50 74.00 1290 71.60
300 0.36 21.60 73.50 74.00 1395 77.60
350 0.38 21.60 77.50 74.00 1470 81.60
24
200 0.33 25.80 80.80 95.00 1550 86.10
250 0.37 25.80 90.50 95.00 1725 95.80
300 0.40 25.80 97.70 95.00 1855 103.00
350 0.43 25.80 104.90 95.00 1985 110.20
30**
150 0.34 32.00 103.50 139.00 2000 111.202000.38 32.00 115.50 139.00 2220 123.20
250 0.42 32.00 127.50 139.00 2435 135.20
300 0.45 32.00 136.50 139.00 2595 144.20
350 0.49 32.00 148.40 139.00 2810 156.10
36**
150 0.38 38.30 138.50 184.00 2675 148.70
200 0.42 38.30 152.90 184.00 2935 163.10
250 0.47 38.30 170.90 184.00 3260 181.10
300 0.51 38.30 185.30 184.00 3520 195.50
350 0.56 38.30 203.20 184.00 3840 213.40
† Including bell; calculated weight of pipe rounded off to the nearest 5 lb.
‡ Including bell; average weight per foot, based on calculated weight of pipe before rounding.
* Tolerances of OD of spigot end: 3–12 in. = +0.06 in. & -0.06 in. ; 14–24 in. = +0.05 in. & -0.08 in. ;
30–36 in. = +0.08 in. & -0.06 in.
** Fastite® Joint
STANDARD DIMENSIONS AND WEIGHTS OF
3” THROUGH 36” PUSH-ON JOINT DUCTILE IRON PIPE
Tyton® Joint
Pipe Size In.
Pipe
Thickness In.
Outside
Diameter *Dimensions In.
From To In.A B
3 .25 .40 3.96 5.80 3.00
4 .25 .41 4.80 7.10 3.156.25 .43 6.90 8.63 3.38
8 .25 .45 9.05 10.94 3.69
10 .26 .47 11.10 13.32 3.7512.28 .49 13.20 15.06 3.75
14 .28 .51 15.30 17.80 5.00
16 .30 .52 17.40 19.98 5.0018.31 .53 19.50 22.00 5.00
20 .33 .54 21.60 24.12 5.25
24 .33 .56 25.80 28.43 5.50
30 .34 .63 32.00 35.40 6.55
36 .38 .73 38.30 41.84 7.00
*Nominal laying length is 18 ft.
Pipe Size In.
Pipe
Thickness
In.
Outside Diameter *Dimensions In.Bolts Bell Weight Lb.
Gland** Bolts Gasket Weight Lb.From To In.B J K1 K2 No.Size In.Length In.
3 .25 .40 3.96 2.50 6.19 7.62 7.69 4 5/8 3 11 7
4 .26 .41 4.80 2.50 7.50 9.06 9.12 4 3/4 3-1/2 16 10
6 .25 .43 6.90 2.50 9.50 11.06 11.12 6 3/4 3-1/2 18 16
8 .27 .45 9.05 2.50 11.75 13.31 13.37 6 3/4 4 24 25
10 .29 .47 11.10 2.50 14.00 15.62 15.62 8 3/4 4 31 30
12 .31 .49 13.20 2.50 16.25 17.88 17.88 8 3/4 4 37 40
14 .33 .51 15.30 3.50 18.75 20.25 20.25 10 3/4 4-1/2 61 45
16 .34 .52 17.40 3.50 21.00 22.50 22.50 12 3/4 4-1/2 74 55
18 .35 .53 19.50 3.50 23.25 24.75 24.75 12 3/4 4-1/2 85 65
20 .36 .54 21.60 3.50 25.50 27.00 27.00 14 3/4 4-1/2 98 85
24 .38 .56 25.80 3.50 30.00 31.50 31.50 16 3/4 5 123 105
* Nominal laying length is 18 ft.
** Weight shown for regular grey cast iron follower gland, corton bolts and rubber gasket.
Pipe
Size
In.
Thickness A
PipeO.D.
B
RetainerO.D.
Full Length Weight - Lb.**SafeEndPullLb.
Class
(A21.51)T AsShipped
Under Water
Full ofAir Full ofWater655.40 6.90 13.88 545 240 465 50,000
8 55 .42 9.05 16.63 770 240 655 70,000
10 55 .44 11.10 19.13 1005 220 860 95,000
12 55 .46 13.20 22.00 1270 155 1080 120,000
14 56 .51 15.30 24.50 1655 160 1410 145,000
16 56 .52 17.40 27.00 1990 45 1685 165,000
18 56 .53 19.50 30.00 2375 -70 2015 195,000 58*.59 2560 110 2170
20 56 .54 21.60 32.75 2810 -200 2375 210,000 59*.63 3110 100 2635
24 56 .56 25.80 38.25 3700 -620 3110 260,000 62*.74 4415 95 3715
30 58 .71 32.00 46.25 5855 -900 4920 335,000 61*.83 6435 -180 5360
36 57 .78 38.30 54.25 8145 -1300 6880 400,000 59*.88 8725 -725 7330
* Thickness required to overcome buoyancy.
** Weights listed are for 18’–0” laying lengths. Nominal full lengths vary by size.
Pipe, Bell, Ball and Retainer are ductile iron.
Dimensions and weights are subject to manufacturing tolerances.
6 in. – 24 in. pressure rating: 350 psi
30 in. –36 in. pressure rating: 250 psi
MECHANICAL JOINT PIPE
BALL AND SOCKET JOINT PIPE
B
15° Max.
A
T
SURE STOP 350 ® GASKET FOR TYTON ® JOINT FROM MCWANE DUCTILE
Sure Stop 350 ® Gaskets are available from 3" through 24" to provide instant and
easy joint restraint for Tyton Joint ® pipe.
Sure Stop 350 Gaskets are
rated for 350 psi working
pressure with a 2:1 safey
factor and allow up to a
5-degree defiection at each
joint. McWane Ductile’s Sure
Stop 350 Gaskets are boltless,
allowing quick, simple
installation without special
wrenches or tools, and are
Underwriters Lab (UL) listed
and Factory Mutual (FM)
approved. McWane Ductile’s
Sure Stop 350 Gaskets can
be furnished with various
gasket compounds, including
the standard SBR, Neoprene,
EPDM, Nitrile and Viton.
Please contact your local
sales representative for
more information.
APPLICATION NOTES
For Ductile iron applications utilizing Tyton
pipe, valves and flttings are made to AWWA
speciflcations.
In cold weather assembly, maintain the
temperature of the gasket above 40° F.
. The socket of the joint should be clean and free
of debris or signiflcant corrosion.
Gasket should be properly seated in the bell socket.
. Keep the pipe and joint in alignment during
assembly. If installed out of alignment, the gasket
can be pushed out of position, creating the
potential for leaks or failure.
If defiection is wanted in the joint, defiect before
fully inserting the joint.
Some extension of the joint will occur when
pressurized. To avoid this, the joint should be
pulled out after assembly to "set" the stainless
steel teeth in the inserted pipe.
Once assembled, the joint can be disassembled
using steel shims.
When cut pipe is used, the following steps are
required:
a. Ensure that the spigot end is properly beveled.
b. Mark the joint depth on the spigot so it is
clear when the joint is fully inserted.
c. Ensure that the pipe meets the required
dimensional tolerances.
Do not reuse Sure Stop 350 Gaskets, as they
may have been damaged during any previous
installation or during removal.
Do not use Sure Stop 350 Gaskets to conduct
electricity through the pipe joint, as they could
be damaged and fail.
Do not use Sure Stop 350 Gaskets in above-
ground applications.
Do not use Sure Stop 350 Gaskets with thick
coating on the pipe exterior.
If Sure Stop 350 Gaskets are used in straight
casings, you must pull the pipe through the
casing. Do not push the pipe.
B
15° Max.
A
T
SURE STOP 350® GASKET
FOR TYTON® JOINT FROM
MCWANE DUCTILE
Sure Stop 350® Gaskets are available from 3" through 24" to provide instant and
easy joint restraint for Tyton Joint® pipe.
Sure Stop 350 Gaskets are
rated for 350 psi working
pressure with a 2:1 safey
factor and allow up to a
5-degree deflection at each
joint. McWane Ductile’s Sure
Stop 350 Gaskets are boltless,
allowing quick, simple
installation without special
wrenches or tools, and are
Underwriters Lab (UL) listed
and Factory Mutual (FM)
approved. McWane Ductile’s
Sure Stop 350 Gaskets can
be furnished with various
gasket compounds, including
the standard SBR, Neoprene,
EPDM, Nitrile and Viton.
Please contact your local
sales representative for
more information.
APPLICATION NOTES
1. For Ductile iron applications utilizing Tyton
pipe, valves and fittings are made to AWWA
specifications.
2. In cold weather assembly, maintain the
temperature of the gasket above 40° F.
3. The socket of the joint should be clean and free
of debris or significant corrosion.
4. Gasket should be properly seated in the bell socket.
5. Keep the pipe and joint in alignment during
assembly. If installed out of alignment, the gasket
can be pushed out of position, creating the
potential for leaks or failure.
6. If deflection is wanted in the joint, deflect before
fully inserting the joint.
7. Some extension of the joint will occur when
pressurized. To avoid this, the joint should be
pulled out after assembly to "set" the stainless
steel teeth in the inserted pipe.
8. Once assembled, the joint can be disassembled
using steel shims.
9. When cut pipe is used, the following steps are
required:
a. Ensure that the spigot end is properly beveled.
b. Mark the joint depth on the spigot so it is
clear when the joint is fully inserted.
c. Ensure that the pipe meets the required
dimensional tolerances.
10. Do not reuse Sure Stop 350 Gaskets, as they
may have been damaged during any previous
installation or during removal.
11. Do not use Sure Stop 350 Gaskets to conduct
electricity through the pipe joint, as they could
be damaged and fail.
12. Do not use Sure Stop 350 Gaskets in above-
ground applications.
13. Do not use Sure Stop 350 Gaskets with thick
coating on the pipe exterior.
14. If Sure Stop 350 Gaskets are used in straight
casings, you must pull the pipe through the
casing. Do not push the pipe.
COMPATIBILITY NOTE
McWane Ductile’s Sure Stop 350® Gasket is
designed for use in Tyton Joint Ductile iron
pipe products manufactured by McWane
Ductile to conform to the latest licensed
Tyton Joint drawings and parameters. Sure
Stop 350 Gaskets may also be used in any
other Tyton Joint provided it conforms to
the latest licensed Tyton Joint drawings and
parameters. Sure Stop 350 Gaskets are
not warrantied for use in any other products
or non-licensed push-on joints. Additionally,
gaskets not provided by McWane Ductile,
whether restrained or non-restrained,
are not warrantied for use in McWane
Ductile products.
Tyton® and Tyton Joint® are registered trademarks of U.S. Pipe and Foundry.
mcwaneductile.com canadapipe.com
NEW JERSEY
183 Sitgreaves St.
Phillipsburg, NJ 08865
908-454-1161
OHIO
2266 S. 6th St.
Coshocton, OH 43812
740-622-6651
UTAH
1401 E. 2000 South
Provo, UT 84606
801-373-6910
CANADA
Suite 1, 55 Frid Street,
Hamilton, Ontario, Canada
L8P 4M3
POCKET ENGINEER
Available for iOS + Android or online at pe.mcwane.com
Rev. June 2021
THICKNESS DESIGN OF DUCTILE IRON PIPE ANSI/AWWA C150/A21.50
DUCTILE IRON PIPE FOR WATER AND OTHER LIQUIDS ANSI/AWWA C151/A21.51, FEDERAL WWP421D, GRADE C
DUCTILE IRON PIPE FOR GRAVITY FLOW SERVICE ANSI/ASTM A746
DUCTILE IRON FITTINGS FOR WATER AND OTHER LIQUIDS (3 in. through 36 in.)ANSI/AWWA C110/A21.10
DUCTILE IRON COMPACT FITTINGS (3 in. through 24 in.)ANSI/AWWA C153/A21.53
FLANGED FITTINGS ANSI/AWWA C110/A21.10, ANSI B16.1
DUCTILE IRON PIPE WITH THREADED FLANGES ANSI/AWWA C115/21.15
COATINGS AND LININGS
Asphaltic ANSI/AWWA C151/A21.51, ANSI/AWWA C110/A21.10, ANSI/AWWA C153/A21.53
Cement Lining ANSI/AWWA C104/A21.4
Various Epoxy Linings and Coatings MANUFACTURER’S STANDARD
Exterior Polyethylene Encasement ANSI/AWWA C105/A21.5
JOINTS — PIPE AND FITTINGS
Push-On and Mechanical Rubber-Gasket Joints ANSI/AWWA C111/A21.11, FEDERAL WWP421D
Flanged ANSI/AWWA C115/A21.15, ANSI B16.1
Grooved and Shouldered ANSI/AWWA C606
PIPE THREADS ANSI B2.1
INSTALLATION ANSI/AWWA C600
STANDARDS APPLICABLE TO DUCTILE IRON PIPE AND FITTINGS
® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTS
HOUSTON CORPORATE TOLL FREE 1-800-999-3009 FAX 281-558-9000
www.starpipeproducts.com
Page 1
REV01
Submittal
MATERIAL: Ductile Iron per ASTM A536
PRESSURE: 350 PSI rating for 2" - 24" sizes, 250 PSI rating for 30" - 48" sizes and 150 PSI rating for 54" - 64" sizes
TESTING: In accordance with ANSI/AWWA C153/A21.53, ANSI/AWWA C111/A21.11, UL and FM requirements
LAYING LENGTH: In accordance with ANSI/AWWA C153/A21.53 (fittings not listed in ANSI/AWWA have dimensions per Star design as noted in the catalog)
DEFLECTION: 2"- 4"=8° | 6"=7° | 8"-12"=5° | 14"-16"=3 ½° | 18"-24"=3° | 30"-64"=2°
WEIGHTS: Are in pounds, unless noted otherwise and do not include accessories, cement lining and coating
FLANGES: Flanged ends on fittings match ANSI/AWWA C115/A21.15 and ANSI B16.1 class 125 flanges
CEMENT LINING: In accordance with ANSI/AWWA C104/A21.4 -- size 2" - 3" single thickness and sizes 4" - 64" double thickness
COATING: Asphaltic seal coat inside and out in accordance with ANSI/AWWA C104/A21.4 and referenced in ANSI/AWWA C153/A21.53
GASKETS: SBR in accordance with ANSI/AWWA C111/A21.11
T-BOLTS/NUTS: Low alloy steel in accordance with ANSI/AWWA C111/A21.11
APPROVALS: 3" - 12" UL/ULC Listed | 2" and greater are UL/ANSI/NSF Standards 61 and 372 | 3" - 16" FM APPROVED. Please consult factory for detail listing and approvals.
DIMENSIONS: All dimensions are in inches unless noted otherwise.
INSTALLATION: Per ANSI/AWWA C600 and C111 using DIP conforming to C150/C151 and PVC pipe conforming to C900/C905
L
K1
X
J
D
F
Ø
2"-24" = 0.31 in.
30"-64" = 0.38 in.B
2°
S
M
K2
7°
0.12 in.C0.75 in.
A
MEMBER
GENERAL SPECIFICATIONS
SUBMITTAL INFORMATION
PROJECT NAME:
ENGINEER:
CONTRACTOR:
SPEC. SECTION:
Ductile Iron MJ Compact Fittings
ANSI/AWWA C153/A21.53
LINING OPTIONS (Please check one): COATING OPTIONS (Please check one):SIZE RANGE (Please specify):
Standard: Cement-lined and asphalt seal coat per ANSI/
AWWA C104/A21.4 and UL/NSF-61
Optional: FBE (Fusion Bonded Epoxy) per ANSI/
AWWA C116/A21.1 and UL/NSF-61 - ID & OD Only
Optional: P401 (Protecto 401) Ceramic Epoxy -
sewer applications only. Not NSF-61
Optional: Other (specify) __________________
Standard: Asphaltic seal coat per ANSI/AWWA C104/
A21.4
Optional: FBE (Fusion Bonded Epoxy) per ANSI/
AWWA C116/A21.1 and UL/NSF-61 - ID & OD Only
Optional: Other (specify) ___________________
Size Range _____________________________
MECHANICALJOINT DIMENSIONS
NOM.
SIZE A DIA. B C DIA. D DIA. F DIA. J DIA. K1 DIA. K2 DIA. L M S Ø X DIA.
BOLTS
SIZE NO.
2 2.50 2.50 3.39 3.50 2.61 4.75 6.19 6.25 0.58 0.62 0.36 28º ¾ ⅝ x 3 2
3 3.96 2.50 4.84 4.94 4.06 6.19 7.62 7.69 0.58 0.62 0.39 28º ¾ ⅝ x 3 4
4 4.80 2.50 5.92 6.02 4.90 7.50 9.06 9.12 0.60 0.75 0.39 28º ⅞ ¾ x 3 ½ 4
6 6.90 2.50 8.02 8.12 7.00 9.50 11.06 11.12 0.63 0.88 0.43 28º ⅞ ¾ x 3 ½ 6
8 9.05 2.50 10.17 10.27 9.15 11.75 13.31 13.37 0.66 1.00 0.45 28º ⅞ ¾ x 3 ½ 6
10 11.10 2.50 12.22 12.34 11.20 14.00 15.62 15.62 0.70 1.00 0.47 28º ⅞ ¾ x 3 ½ 8
12 13.20 2.50 14.32 14.44 13.30 16.25 17.88 17.88 0.73 1.00 0.49 28º ⅞ ¾ x 3 ½ 8
14 15.30 3.50 16.40 16.54 15.44 18.75 20.25 20.25 0.79 1.25 0.55 28º ⅞ ¾ x 4 10
16 17.40 3.50 18.50 18.64 17.54 21.00 22.50 22.50 0.85 1.31 0.58 28º ⅞ ¾ x 4 12
18 19.50 3.50 20.60 20.74 19.64 23.25 24.83 24.75 1.00 1.38 0.68 28º ⅞ ¾ x 4 12
20 21.60 3.50 22.70 22.84 21.74 25.50 27.08 27.00 1.02 1.44 0.69 28º ⅞ ¾ x 4 14
24 25.80 3.50 26.90 27.04 25.94 30.00 31.58 31.50 1.02 1.56 0.75 28º ⅞ ¾ x 4 ½ 16
30 32.00 4.00 33.29 33.46 32.17 36.88 39.12 39.12 1.31 2.00 0.82 20º 1 ⅛ 1 x 5 ½ 20
36 38.30 4.00 39.59 39.76 38.47 43.75 46.00 46.00 1.45 2.00 1.00 20º 1 ⅛ 1 x 5 ½ 24
42 44.50 4.00 45.79 45.96 44.67 50.62 53.12 53.12 1.45 2.00 1.25 20º 1 ⅜ 1 ¼ x 6 28
48 50.80 4.00 52.09 52.26 50.97 57.50 60.00 60.00 1.45 2.00 1.35 20º 1 ⅜ 1 ¼ x 6 32
54 57.56 4.00 58.82 59.02 57.73 63.20 65.70 65.70 1.88 2.00 1.50 20º 1 ⅜ 1 ¼ x 6 ½ 36
60 61.61 4.00 62.87 63.07 61.78 67.72 70.22 70.22 1.88 2.00 1.55 20º 1 ⅜ 1 ¼ x 6 ½ 36
64 65.67 4.00 66.96 67.13 65.84 71.86 74.36 74.36 1.88 2.00 1.62 20º 1 ⅜ 1 ¼ x 6 ½ 38
® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTS
HOUSTON CORPORATE TOLL FREE 1-800-999-3009 FAX 281-558-9000
www.starpipeproducts.com
Page 43
UCAT.19.01
Flanged Fittings
O.D.
TB.C.SIZEMATERIAL: Ductile iron per ASTM A536
PRESSURE: 250 PSI ratiing for 1" - 48" sizes and 150 PSI rating for 54" - 64"
TESTING: In accordance with ANSI/AWWA C110/A21.10, UL and FM requirements
LAYING LENGTH: 2" - 48" sizes in accordance with ANSI/AWWA C110/A21.10 and ANSI B16.1 and 54" - 64" sizes in accordance with ANSI/AWWA C153/
A21.53 (fittings not listed in ANSI/AWWA have dimensions per Star design as noted in the catalog)
WEIGHTS: Are in pounds, unless noted otherwise and do not include accessories, cement lining and coatings
DRILLING: In accordance with ANSI/AWWA C110/A21.10, ANSI/AWWA C153/A21.53 and ANSI B16.1 Class 125 Flanges
CEMENT LINING: In accordance with ANSI/AWWA C104/A21.4 -- size 1" - 3" single thickness and sizes 4" - 64" double thickness. Click here for a pressure jetting discussion or visit http://www.starpipeproducts.com/pressure_cleaning_guidelines.asp.
COATING: Asphaltic seal coat inside in accordance with ANSI/AWWA C104/A21.4 and prime coat outside
APPROVALS: 2" - 12" Underwriters Laboratories and ULC Listed and Factory Mutual approved for 300 PSI rating. Please consult factory for detail listing and
approvals. 3" and greater are UL/ANSI/NSF Standards 61 and 372.
DIMENSIONS: All dimensions are in inches unless noted otherwise.
INSTALLATION: Per ANSI/AWWA C110 and C111
GENERAL SPECIFICATIONS
1" - 64" DUCTILE IRON FLANGED FITTINGS
Utility Pipe Fittings and Accessories
ANSI/AWWA C110/A21.10
FLANGE DETAILS
NOM. SIZE O.D.B.C.T BOLT HOLEDIA.
BOLTS
SIZE NO.
1 4.25 3.12 0.44 0.62 ½ x 2 4
1 ½5.00 3.88 0.56 0.62 ½ x 2 4
2 6.00 4.75 0.62 0.75 ⅝ x 2 ¼4
2 ½7.00 5.50 0.69 0.75 ⅝ x 2 ½4
3 7.50 6.00 0.75 0.75 ⅝ x 2 ½4
4 9.00 7.50 0.94 0.75 ⅝ x 3 8
5 10.00 8.50 0.94 0.88 ¾ x 3 8
6 11.00 9.50 1.00 0.88 ¾ x 3 ½8
8 13.50 11.75 1.12 0.88 ¾ x 3 ½8
10 16.00 14.25 1.19 1.00 ⅞ x 4 12
12 19.00 17.00 1.25 1.00 ⅞ x 4 12
14 21.00 18.75 1.38 1.13 1 x 4 ½12
16 23.50 21.25 1.44 1.13 1 x 4 ½16
18 25.00 22.75 1.56 1.25 1 ⅛ x 5 16
20 27.50 25.00 1.69 1.25 1 ⅛ x 5 20
24 32.00 29.50 1.88 1.38 1 ¼ x 5 ½20
30 38.75 36.00 2.12 1.38 1 ¼ x 6 ½28
36 46.00 42.75 2.38 1.63 1 ½ x 7 32
42 53.00 49.50 2.62 1.63 1 ½ x 7 ½36
48 59.50 56.00 2.75 1.63 1 ½ x 8 44
54 66.25 62.75 3.00 2.00 1 ¾ x 8 ½44
60 73.00 69.25 3.12 2.00 1 ¾ x 9 52
64 80.00 76.00 3.38 2.00 1 ¾ x 9 52
APPROVED
MEMBER
DI C110 Flange Fittings
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE
FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT
REJECTED
BY DATE
ü
06/17/2022
TimP
® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTSHOUSTON CORPORATE TOLL FREE 1-800-999-3009 FAX 281-558-9000www.starpipeproducts.com
VB - 20
Municipal & Construction CastingsVALVE BOXES
VER.12.01
VB-0034940 8" VALVE BOX
Notes:- Material - Cast Iron Per ASTM A48 Class 30B- Dimensions in Inches
ITEM CODE DETAILS
VBST940-8W COMPLETE WATER
VBST940-8S COMPLETE SEWER
R VBST940-8W&S
CI VALVE BOX
AST IRON PER ASTM A48 CLASS 30B.
E WEIGHT W/LID= 34.5 LBS (WATER)
WATER
E WEIGHT W/LID= 30.5 LBS (SEWER)
SEWER
VBST940-8W&S
CI VALVE BOX
SEWER
1. MATERIAL - CAST IRON PER ASTM A48 CLASS 30B.
NOTE:
2. APPROXIMATE WEIGHT W/LID= 34.5 LBS (WATER)
WATER
3. APPROXIMATE WEIGHT W/LID= 30.5 LBS (SEWER)
SEWER
FORM E-14 Rev. B
STAR VBST940-18W&S
CI VALVE BOX
1. MATERIAL - CAST IRON PER ASTM A48 CLASS 30B.
NOTE:
2. APPROXIMATE WEIGHT W/LID= 42.5 LBS (WATER)
WATER
3. APPROXIMATE WEIGHT W/LID= 38.5 LBS (SEWER)
SEWER
FORM E-14 Rev. B
8.56
0.44
1.38
8.06
3.44
VB-0035940 18" VALVE BOX
Notes:- Material - Cast Iron Per ASTM A48 Class 30B- Dimensions in Inches
ITEM CODE DETAILS
VBST940-18W COMPLETE WATER
VBST940-18S COMPLETE SEWER
VBST940-18T TOP ONLY
VBST940L WATER LID
VBST940LS SEWER LID
R VBST940-8W&S
CI VALVE BOX
WATER
SEWER
VBST940-8W&S
CI VALVE BOX
SEWER
8.06
3.44
11.88
0.31
1.38
9.31
1
6
9.5
1
6
18
045 Valve Box Top & Lid Water
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE
FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT
REJECTED
BY DATE
ü
06/17/2022TimP
® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTSHOUSTON CORPORATE TOLL FREE 1-800-999-3009 FAX 281-558-9000www.starpipeproducts.com
VB - 21
Municipal & Construction CastingsVALVE BOXES
VER.12.01
VB-0037DEEP WELL VALVE BOX BOTTOM
Notes:- Material - Cast Iron Per ASTM A48 Class 30B- Dimensions in Inches
ITEM CODE DETAILS(L)
VBB24DW 24
VBB30DW 30
VBB36DW 36
VBB42DW 42
TAR
VBB__DW
24, 30, 36 & 42
DEEP WELL CI VB BOTTOM
STAR
VBB__DW
1. MATERIAL - CAST IRON PER ASTM A48 CLASS 30B.
NOTE:
2. APPROXIMATE WEIGHT 24" = 40 LBS
24, 30, 36 & 42
DEEP WELL CI VB BOTTOM
30" = 45 LBS
36" = 50 LBS
42" = 55 LBS
X
24"
30"
36"
42"
SIZE
24.00
30.00
36.00
42.00
VB-0036950 VALVE BOX
Notes:- Material - Cast Iron Per ASTM A48 Class 30B- Dimensions in Inches
ITEM CODE DETAILS
VBST950 COMPLETE
VBST950950 CI VALVE BOX
TM A48 CLASS 30B.
ID = 15 LBS
R TOP = 40 LBS
WATER
1. MATERIAL - CAST IRON PER ASTM A48 CLASS 30B.
NOTE:
2. APPROXIMATE WEIGHT FOR LID = 15 LBS
FOR TOP = 40 LBS
WATER
FORM E-14 Rev. B
7.75
6.75
0.63
10.13
0.38
0.25
5.59
LID
TOP
L
7.5 1
2
12
1
10
6.5
7.5
1
8.5
7.5
24" Bottom With Deep Skirt
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED
REVISE AND RESUBMIT
REJECTED
BY DATE
ü
REV.21.02
® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTSHOUSTON CORPORATE TOLL FREE 1-800-999-3009 FAX 281-558-9000www.starpipeproducts.com
Page 1
Joint Restraint Submittal Form
MEMBER
Stargrip® series 3000 for Ductile Iron Pipe
• Gland is made from high strength Ductile Iron per ASTM A536, Grade 65-45-12 and is compatible with all Mechanical Joints conforming to ANSI/AWWA C111/A21.11.
• The Wedge Assembly is designed with a Break-Off Torque Control Head, ensuring proper installation.
• The Stargrip® offers a full 5° deflection through 12" size, 3° on 14"-24", 2° on 30"-36", 1° on 42"-48" and 1/2° on 54" & 60".
• Minimum safety factor of 2:1
• Stargrip® sizes 3"-36" are listed with Underwriters Laboratories Inc. and sizes 3"-12" are approved by Factory Mutual Research.
• The Wedges are heat treated to a minimum of 370 BHN.
• The Wedge Assembly is designed to fit specific pipe sizes.
• Stargrip® eliminates tie rods and thrust blocks.
• Standard gland color is Black.
• Stargrip® may also be used on minimum SCH 40 steel pipe* up to 12" (*transition gasket required on 12" and under). For 14" and larger steel applications, contact Star Pipe.
• Gland: Ductile Iron per ASTM A536, Grade 65-45-12
• Wedges: Ductile Iron per ASTM A536, Grade 65-45-12 heat treated to a minimum of 370 BHN
◆ Wedge Finish: Thermally cured fluoropolymer epoxy coating
SUBMITTAL INFORMATION
MATERIAL SPECIFICATIONS:
FEATURES & ADVANTAGES
PROJECT NAME:
ENGINEER:
CONTRACTOR:
SPEC. SECTION:
HARDWARE OPTIONS (Please check one):
Standard: T-bolts are high strength low alloy steel manufactured in accordance with ANSI/AWWA C111/A21.11-00
Optional: T-bolts and nuts alloy SS 304 per ASTM F593
Optional: T-bolts and nuts alloy SS 316 per ASTM F593
Optional: T-bolts and nuts Fluoropolymer Star-Blue coated high strength low alloy steel manufactured in accordance with ANSI/AWWA C111/A21.11-00
GLAND FINISH OPTIONS (Please check one):
COUNTRY OF ORIGIN OPTION (Please check one):
Standard: alkyd enamel coating
Optional: StarbondTM TGIC polyester powder coating applied by an electrostatic spray process
Optional: Other (specify) _____________________________
Import
Domestic - AIS Compliant
Mechanical Joint Wedge Action Restraint
for Ductile Iron Pipe
Stargrip®
series 3000Mechanical Joint Grip Packs
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
Page 18
® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTS
HOUSTON CORPORATE TOLL FREE 1-800-999-3009 FAX 281-558-9000
www.starpipeproducts.com
UCAT.19.01
Utility Pipe Fittings and Accessories
ANSI/AWWA C111/A21.11
Utility Pipe Fittings and Accessories
MJ COMPACT GLANDS
NOM.SIZE O.D.A B C I.D.B.C.BOLTHOLE BOLTQTY WT(LBS.)
2 6.12 0.62 1.18 3.40 2.61 4.75 Ø0.75 2 1
3 7.69 0.62 1.37 4.84 4.06 6.19 Ø0.75 4 2
4 9.12 0.75 1.50 5.92 4.90 7.50 Ø0.88 4 3
6 11.12 0.88 1.63 8.02 7.00 9.50 Ø0.88 6 4
8 13.37 1.00 1.75 10.17 9.15 11.75 Ø0.88 6 5
10 15.62 1.00 1.75 12.22 11.20 14.00 Ø0.88 8 7
12 17.88 1.00 1.75 14.32 13.30 16.25 Ø0.88 8 8
14 20.25 1.25 2.00 16.40 15.44 18.75 Ø0.88 10 11
16 22.50 1.31 2.06 18.50 17.54 21.00 Ø0.88 12 14
18 24.75 1.38 2.13 20.60 19.64 23.25 Ø0.88 12 19
20 27.00 1.44 2.19 22.70 21.74 25.50 Ø0.88 14 27
24 31.50 1.56 2.31 26.90 25.94 30.00 Ø0.88 16 36
30 39.12 2.00 2.75 33.29 32.17 36.88 Ø1.13 20 90
36 46.00 2.00 2.75 39.59 38.47 43.75 Ø1.13 24 118
42 53.12 2.00 2.75 45.79 44.67 50.62 Ø1.38 28 151
48 60.00 2.00 2.75 52.09 50.97 57.50 Ø1.38 32 187
54 65.70 2.00 2.75 58.82 57.73 63.20 Ø1.38 36 362
60 70.22 2.00 2.75 62.87 61.78 67.72 Ø1.38 36 413
64 74.36 2.00 2.75 66.96 65.84 71.86 Ø1.38 38 444
MATERIAL: Ductile Iron per ASTM A536
PRESSURE: 350 PSI rating for 2" - 24" sizes, 250 PSI rating for 30" - 48" sizes and 150 PSI rating for 54" - 64" sizes
TESTING: In accordance with ANSI/AWWA C111/A21.11, UL and FM requirements
DIMENSIONS: Are in accordance with ANSI/AWWA C111/A21.11, UL and FM requirements and are in inches unless noted otherwise
WEIGHTS: Are in pounds, unless noted otherwise and do not include accessories
COATING: Asphaltic seal coat is in accordance with ANSI/AWWA C104/A21.4 unless otherwise specified.
APPROVALS: Compact Glands 3" - 12" Underwrites Laboratories & ULC Listed. Factory Mutual approved 3"-16". MEMBER
GENERAL SPECIFICATION
GLANDS, GASKETS, BOLTS & NUTS
MJ Accessories
O.D.B.C.
I.D.
C
B
A
O.D.
B.C.
I.D.
C
B
AMJ8INDISTAR
3
5
0 RATSM JG30^"DI250SIZES 54” - 64”SIZES 30” - 48”SIZES 2” - 24”
Mechanical Joint Accessory Pack
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
Fabricated Flange Pipes
E GO.D.
JCH
FLG. x FLG.
A
EG O.D.
C
FLG. x M.J.
MJ
H L
P
A
K EG O.D.
C
FLG. x P.E.
J
H A
Size A B C O.D.E G H No. of
Flg’d Bolt
Holes
J K L No. Of
M.J. Bolt
HOes
M PMin.Max.Min.Max.Min.Max.Min.Max.Min.Max.
3 ••0.31 3.90 4.02 6.00 7.50 0.63 0.87 4 0.750 6.13 6.25 0.88 0.94 4 0.75 0.81 2.50
4 A A 0.32 4.74 4.86 7.50 9.00 0.82 1.06 8 0.750 7.44 7.56 0.94 1.00 4 0.875 0.935 2.50
6 S S 0.34 6.84 6.96 9.50 11.00 0.88 1.12 8 0.875 9.44 9.56 1.00 1.06 6 0.875 0.935 2.50
8 ••0.36 8.99 9.11 11.75 13.50 1.00 1.24 8 0.875 11.69 11.81 1.04 1.12 6 0.875 0.935 2.50
10 ••0.38 11.04 11.16 14.25 16.00 1.07 1.31 12 1.000 13.94 14.06 1.11 1.19 8 0.875 0.935 2.50
12 R R 0.40 13.14 13.26 17.00 19.00 1.13 1.37 12 1.000 16.19 16.31 1.17 1.25 8 0.875 0.935 2.50
14 E E 0.42 15.22 15.35 18.75 21.00 1.19 1.57 12 1.125 18.69 18.81 1.19 1.31 10 0.875 0.935 3.50
16 Q Q 0.43 17.32 17.45 21.25 23.50 1.25 1.63 16 1.125 20.94 21.06 1.26 1.38 12 0.875 0.935 3.50
18 U U 0.44 19.42 19.55 22.75 25.00 1.37 1.75 16 1.250 23.19 23.31 1.32 1.44 12 0.875 0.935 3.50
20 I I 0.45 21.52 21.65 25.00 27.50 1.50 1.88 20 1.250 25.44 25.56 1.38 1.50 14 0.875 0.935 3.50
24 R R 0.47 25.72 25.85 29.50 32.00 1.69 2.07 20 1.375 29.94 30.06 1.50 1.62 16 0.875 0.935 3.50
30 E E 0.51 31.94 32.08 36.00 38.75 1.87 2.37 28 1.375 36.82 36.94 1.69 1.81 20 1.125 1.185 4.00
36 D D 0.58 38.24 38.38 42.75 46.00 2.13 2.63 32 1.625 43.69 43.81 1.88 2.00 24 1.125 1.185 4.00
42 ••0.65 44.44 44.58 49.50 53.00 2.37 2.87 36 1.625 50.56 50.68 1.88 2.00 28 1.375 1.435 4.00
48 ••0.72 50.74 50.88 56.00 59.50 2.50 3.00 44 1.625 57.44 57.56 1.88 2.00 32 1.375 1.435 4.00
54 ••0.81 57.40 57.64 62.75 62.75 2.75 3.25 44 1.875 N/A N/A N/A N/A N/A N/A N/A N/A
60 ••0.83 61.51 61.65 69.25 73.00 2.87 3.37 52 2.000 N/A N/A N/A N/A N/A N/A N/A N/A
64 ••0.87 65.57 65.71 76.00 80.00 3.13 3.63 52 2.000 N/A N/A N/A N/A N/A N/A N/A N/A
1. Tolerance on length of FLG. x FLG. and FLG. x M.J. pipe shall be ± 0.125”.
2. Tolerance on length of FLG. x P.E. shall be ± 0.25”.
3. Above material shall meet all applicable sections of ANSI A21.10, A21.15, A21.51, B2.1, B16.1 & AWWA C110, C115, C150, C151 and all revisions thereto.
4. Flanged pipe shall be ductile iron pipe with ductile iron flanges threaded on.
5. Flange pipe is provided with cement lining per AWWA C104/A21.4. If other linings are required, contact your local sales representative.
6. The mechanical joint bell for 30” and 36” sizes of ductile iron pipe have thicknesses different from those shown in ANSI A21.11, which are based on gray iron
pipe. These reduced thicknesses provide a lighter-weight bell which is compatible with the wall thickness of ductile iron pipe.
7. Submitted material only. Consult your engineer for application.
8. 250 lb. faced and drilled flanges available upon request.
9. Flange-Tyte gaskets are included with all 14” or larger ductile iron flanged joint products supplied by U.S. Pipe. These are
required during installation, and failure to use these gaskets could result in voiding the manufacturer’s warranty. Refer
to product data sheets for additional information.
FLG. DETAIL
J
EG
www.uspipe.com 866.DIP.PIPE
Rev. 02072020
Document # 20-1-0022 04/03/2019www.romac.com
21919 20th Avenue SE • Suite 100 • Bothell, WA 98021
Phone (425) 951-6200 • 1-800-426-9341 • Fax (425) 951-6201
This information is based on the best data available at the date printed above. Please check with Romac for any updates or changes.
SUBMITTAL INFORMATION
PRESSURE
USE
STANDARD
SIZES & RANGES
MATERIALS
CASTINGS The end rings and center rings are cast from ductile (odular) iron, meeting or exceeding ASTM A 536, Grade 65-45-12.
GASKETS Made from virgin Ethylene Propylene Diene Monomer Rubber (EPDM) compounded for water and sewer ser-vice in accordance with ASTM D2000, NSF 61 Certified. Other compounds available upon request.
BOLTS AND NUTS 5/8 inch, High strength low alloy steel trackhead bolts. National coarse rolled thread and heavy hex nuts. Steel meets AWWA C-111 composition specifications. Stain-less steel bolts and nuts available on request.
COATINGS Shop coat applied to cast parts for corrosion protection in transit. Fusion bonded epoxy, liquid epoxy and other coatings available on request.
When properly installed on standard steel pipe and larger the Romac Style XR501 coupling can be used at working pressures up to 260 psi. Higher working pressures available for specific applications. NOTE: for pipe ODs smaller than standard steel do not exceed 20 PSI.
Provides an Extended Range Coupling for multi-purpose use. One gasket, center ring and end ring for SDR 35 PVC sewer through Class 200 A/C pipe sizes. NOTE: for pipe ODs smaller than standard steel do not exceed 20 PSI.
Romac 501 couplings meet the specifications set forth in the AWWA Standard C219 coupling spec.
See catalog.
XR501 EXTENDED RANGE COUPLING
NSF61 certified upon request.Document # 20-1-0022 04/03/2019www.romac.com
21919 20th Avenue SE • Suite 100 • Bothell, WA 98021
Phone (425) 951-6200 • 1-800-426-9341 • Fax (425) 951-6201
This information is based on the best data available at the date printed above. Please check with Romac for any updates or changes.
SUBMITTAL INFORMATION
UL LISTED
UNI-BELL UNI-B-13-92
FM APPROVED
USE
PIPE COMPATABILITY
The Romac )rip Ring is used for the restraint of mechanical Loint pipe, valves, fittings, and fire h[drants in water distribution and fire protection lines. )rip Rings replace costl[ concrete thrust blocks, corrodible steel tie rods and clamps, and fittings using radial bolts or pads. Not for use on plain end mechanical Loint fittings or Molecularl[ 1ri-ented 2ol[vin[lchloride
28C1 AWWA C909-02.
)rip Rings ma[ be used on most Ductile +ron, Cast +ron, 28C. See )rip Ring 2ipe Restrainer Application Chart for specific applications. Chart is on the back of the )rip Ring +nstallation +nstructions or in the current Romac catalog under restraint s[stem.
Ma[ be used up to the pressure rating of the pipe when used on Ductile +ron, C+, and 28C pipe. See catalog and installation instructions
7. listed for cast iron and ductile iron pipe at 50 psi working pressure. Also listed for 28C C900 pipe at the pressure rating of the pipe. 7. reference number is 6M6
7N+-$-1-92 is now governed b[ ASTM F 16-96. The )rip Ring meets the reSuirements of F 16-96.
FM approved for cast iron and ductile iron pipe at 15 psi working pressure
1 test. Also approved for 28C C900 pipe at the pressure rating of the pipe.
GRIP RING™ PIPE RESTRAINER 4 THROUGH 12 INCH
MATERIALS
GLAND (FOLLOWER) Ductile
nodular iron, meeting or eZceeding ASTM A 56, )rade 65-5-12.
RING Ductile
nodular iron, meeting or eZceeding ASTM A 56, )rade 65-5-12. Heat treated using a proprietar[ process to assure proper penetration of rigid pipe materials.
GAP CAP Heav[ gauge 0 stainless steel
10 and 12 inch onl[.
GASKET A standard M, gasket is used with this fitting. See ANS+AWWA C111A21.11 for specifications. Transition gaskets ma[ be used for steel
+2S pipe si\e 28C.
BOLTS AND NUTS Standard M, tee-bolts and nuts are used with this fit-ting. See ANS+AWWA C111A21.11 for specifications.
COATINGS AND COLORS Shop coat applied to the castings for corrosion protec-tion in transit. )lands are [ellow to distinguish them from standard M, fittings. Rings are color coded $.AC- for Ductile +ron si\e and R'D for +2S.PERFORMANCE
Document # 20-8-0006 1/17www.romac.com
21919 20th Avenue SE • Suite 100 • Bothell, WA 98021
Phone (425) 951-6200 • 1-800-426-9341 • Fax (425) 951-6201
This information is based on the best data available at the date printed above. Please check with Romac for any updates or changes.
SUBMITTAL INFORMATION
STANDARD
ANCHOR PINS
SIZES & RANGES
PRESSURE
MATERIALS
CASTINGS The end ring and flanged body are cast from ductile (nodular) iron, meeting or exceeding ASTM A 536.
FLANGE Compatible with ANSI Class 125 and 150 bolt circles.
GASKETS Gaskets are made from virgin Styrene Butadiene Rub-ber (SBR) compounded for water and sewer service in accordance with ASTM D 2000 MBA 710. Other compounds available for petroleum, chemical, or high temperature service.
BOLTS AND NUTS High strength low alloy steel trackhead and T-head bolt National coarse rolled thread and heavy hex nuts. Steel meets AWWA C111 composition specifications. The 10" size uses electro-galvanized mild steel flange bolts and nuts with a hex head, and ductile iron through bolts. The 12" size uses electro-galvanized mild steel flange bolts and nuts with a hex head, and mild steel through bolts (AWWA C111 composition specifications). All above nuts and bolts are corrosion resistant. Stainless steel bolts and nuts available on request.
COATINGS Shop coat applied to cast parts for corrosion protection in transit. Fusion bonded epoxy, liquid epoxy and other coatings available on request.
Romac 501 couplings meet the specifications set forth in the AWWA Standard C219 coupling spec.
When properly installed on a pipe that is within the correct outside diameter range, the FCA 501 couplings can be used at working pressures up to 260 psi.
Anchor pins to restrain fitting available as option.
See Catalog.
FCA501 FLANGED COUPLING ADAPTER
Document # 05-8-0012 1/17www.romac.com
21919 20th Avenue SE • Suite 100 • Bothell, WA 98021
Phone (425) 951-6200 • 1-800-426-9341 • Fax (425) 951-6201
This information is based on the best data available at the date printed above. Please check with Romac for any updates or changes.
SUBMITTAL INFORMATION
UL LISTED
UNI-BELL UNI-B-13-92
FM APPROVED
USE
PIPE COMPATABILITY
The Romac Grip Ring is used for the restraint of mechanical joint pipe, valves, fittings, and fire hydrants in water distribution and fire protection lines. Grip Rings replace costly concrete thrust blocks, corrodible steel tie rods and clamps, and fittings using radial bolts or pads. Not for use on plain end mechanical joint fittings or Molecularly Ori-ented Polyvinylchloride (PVCO) AWWA C909-02.
Grip Rings may be used on most Ductile Iron, Cast Iron, PVC. See Grip Ring Pipe Restrainer Application Chart for specific applications. Chart is on the back of the Grip Ring Installation Instructions or in the current Romac catalog under restraint system.
May be used up to the pressure rating of the pipe when used on Ductile Iron, CI, and PVC pipe. See catalog and installation instructions
UL listed for cast iron and ductile iron pipe at 350 psi working pressure. Also listed for PVC C900 pipe at the pressure rating of the pipe. UL reference number is 6M46
UNI-B-13-92 is now governed by ASTM F 1674-96. The Grip Ring meets the requirements of F 1674-96.
FM approved for cast iron and ductile iron pipe at 175 psi working pressure (4 : 1 test). Also approved for PVC C900 pipe at the pressure rating of the pipe.
GRIP RING™ PIPE RESTRAINER 4 THROUGH 12 INCH
MATERIALS
GLAND (FOLLOWER) Ductile (nodular) iron, meeting or exceeding ASTM A 536, Grade 65-45-12.
RING Ductile (nodular) iron, meeting or exceeding ASTM A 536, Grade 65-45-12. Heat treated using a proprietary process to assure proper penetration of rigid pipe materials.
GAP CAP Heavy gauge 304 stainless steel (10 and 12 inch only).
GASKET A standard MJ gasket is used with this fitting. See ANSI/AWWA C111/A21.11 for specifications. Transition gaskets may be used for steel (IPS) pipe size PVC.
BOLTS AND NUTS Standard MJ tee-bolts and nuts are used with this fit-ting. See ANSI/AWWA C111/A21.11 for specifications.
COATINGS AND COLORS Shop coat applied to the castings for corrosion protec-tion in transit. Glands are yellow to distinguish them from standard MJ fittings. Rings are color coded BLACK for Ductile Iron size and RED for IPS.PERFORMANCE
Romac Grip Ring for CI Connections
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
PRODUCT SPECIFICATIONS
MATERIAL:
COLOR:
• Polycase LLDPE encasement film is a carefully engineered linear low density virgin polyethylene resin film
designed to meet the requirements of the ANSI/AWWA C105/A21.5 standard.
• Polyethylene film may be supplied in its natural color, white, black, or weather-resistant black.
SIZE RANGE:• 8 mil Stock Tube Sizes (based on ANSI/AWWA C105/A21.5 Table 1)
Rev January 2018 SIGMA Corporation www.sigmaco.com
8 Mil Linear Low Density Polyethylene
SPECIFICATIONS:
Physical Attribute Test Direction ANSI/AWWA C105/A21.5MINIMUM REQUIREMENT SIGMA LLDP TYPICAL TEST VALUES
TENSILE STRENGTH ASTM D882 MACHINE DIRECTION 3600psi 4635psi
TRANSVERSE DIRECTION 3600psi 4216psi
ELONGATION STM D882 MACHINE DIRECTION 800%948%
TRANSVERSE DIRECTION 800%1012%
DIELECTRIC STRENGTH ASTM D149 (VOLTS / MIL)n/a 800 volts / mil 1786 volts / mil
IMPACT RESISTANCE ASTM D1709 (grams)n/a 600 grams 928 grams
PROPAGATION TEARRESISTANCE ASTM D1922 (gf)
MACHINE DIRECTION 2550 grams/force 4082 grams/force
TRANSVERSE DIRECTION 2550 grams/force 6159 grams/force
Pipe Size Size Continuous Roll Length Part Number Perforated 22 Part Number Perforated 20 Part Number
4-6”8”
10”12”
14”16”18”
20”24”
30”36-42”48”
54”60-64”
16”20”
24”27”
30”34”37”
41”54”
67”81”95”
108”121”
300300
300300
300300300
300300
300300200
200110
47-PW1647-PW20
47-PW2447-PW27
47-PW3047-PW3447-PW37
47-PW4147-PW54
47-PW6747-PW8147-PW95
47-PW10847-PW121
506506
440396
352308308
264220
220176220
47-PW162247-PW2022
47-PW242247-PW2722
47-PW302247-PW342247-PW3722
47-PW412247-PW5422
47-PW672247-PW812247-PW9522
300300
300300
300300300
220220
220220220
47-PW162047-PW2020
47-PW242047-PW2720
47-PW302047-PW342047-PW3720
47-PW412047-PW5420
47-PW672047-PW812047-PW9520
Pipe Size Size Sigma Blue Part Number Sigma Green Part Number Sigma Lavendar Part Number
8”
12”16”
20”24”30”
36-42”
20”
27”34”
41”54”67”
81”
300
300300
200200200
200
47-PW20B
47-PW27B47-PW34B
47-PW41B47-PW54B47-PW67B
47-PW81B
300
300300
200200200
47-PW20G
47-PW27G47-PW34G
47-PW41G47-PW54G47-PW67G
300
300300
200200200
47-PW20L
47-PW27L47-PW34L
47-PW41L47-PW54L47-PW67L
8 Mil PolyWrap
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
RECTANGULAR METER BOX SPECIFICATIONS
Product Style Size Depth
RMB1015-FL Flared-Wall 10”x15”12”, 18”, and 24”
RMB1015-SW Straight-Wall 10”x15”12”
RMB1118-SW Straight-Wall 11”x18”12” and 18”
RMB1324-SW Straight-Wall 13”x24”12” and 18”
RMB1527-SW Straight-Wall 15”x27 12” and 18”
RMB1730-SW Straight-Wall 17”x30”12” and 18”
RMB1730-FL Flared-Wall 17”x30” 18”
Manufacture Process: Sigma-Raven rectangular meter boxes are produced using High Density Polyethylene regrind and virgin resins in a series of LAMINATED WALLS with an optional white interior coating. The outer wall is LAMINATED to the interior wall providing greater side load-bearing capacity. When the two walls are laminated together the Molecular Structure (fibers) from each wall are crossed, creating a dual layer of much greater strength and wall thickness. Wall thickness shall be such that when buried, it will support an incidental traffic load as explained with an appropriate traffic rated lid.
Impact: Impact tests shall be conducted at two different locations. These are (1) the top of pit at lid area and (2) at the center area. Failure of the test specimen shall be any crack, split or shatter of the wall section. Test using a 10-lb Tub B and flat plate Holder B. Test one pit per run if failure occurs test 3 more pits. If no failure occurs the run is approved.
Interior: Interior shall be Black or optional White.
Settling: Rectangular meter boxes shall have an anti-settling flange around the base.
Lids: Materials include HDPE and Ductile Iron.
LIMITED-WARRANTY: SIGMA-Raven warrants Poly boxes and lids to be free of manufacturing defects at ship point. Warranty is limited to replacement or unit price at discretion of Sigma-Raven. Sigma-Raven shall not be liable for any damages of any kind.
700 Goldman Drive
Cream Ridge, NJ 800 999 2550 pSIGMA Corporation www.sigmaco.com
Rev October 2016
RMB 1324-18
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022
902 South 2nd Street
Oskaloosa, IA 52577
Ph 641-673-8611
Fx 641-673-8269
*PATENT PENDING
REVISION A-2018
COMMITTED TO ENVIRONMENTAL RESPONSIBILITY
Clow Valve Company is committed to protecting our natural resources through environmentally responsible
manufacturing practices, including the use of 80+% recycled content in our hydrants and valves.
RECOMMENDED SPECIFICATIONS
1. Valves shall conform to the latest revision of AWWA
Standard C509 covering resilient seated gate valves for
water supply service.
2. The valves shall have an iron body, bonnet, and O-ring
plate. The wedge shall be fully encapsulated with
rubber.
3. The sealing rubber shall be permanently bonded to the
wedge per ASTM D249.
4. Valves shall be supplied with O-ring seals at all pressure
retaining joints. No flat gaskets shall be allowed.
5. The valves shall be either non-rising stem (NRS) or
rising stem (OS&Y), opened by turning left or right, and
provided with 2" square operating nut or a handwheel.
The operating nut and the handwheel shall be marked
indicating the direction to open with the word “OPEN”
and an arrow.
6. NRS stems shall be cast copper alloy with integral
collars in full compliance with AWWA C509. All stems
shall operate with copper alloy stem nuts independent
of the wedge.
7. All NRS stems shall have two O-rings located above
thrust collar and one below. The upper o-rings shall be
replaceable with valve fully opened and subjected to full
pressure. The stems on 2"–12" NRS valves shall have a
low torque thrust bearing located both above and below
the stem collar to reduce friction during operation.
8. The waterway shall be smooth, unobstructed and free
of all pockets, cavities and depressions in the seat area.
Valves made with a tapping flange shall accept a full
size tapping cutter.
9. The body, bonnet and O-ring plate shall be coated both
on the interior and exterior with fusion bonded epoxy.
Epoxy shall be applied in accordance with AWWA C550
and certified per NSF 61.
10. Each valve shall have the manufacturer’s name, the
pressure rating, country of origin and the year in which
it was manufactured cast on the body. Prior to shipment
from the factory, each valve shall be hydrostatically
pressure tested according to the requirements of
AWWA C509 (and UL/FM where applicable).
11. Valves shall have all component parts cast and
assembled in the USA and shall be manufactured by the
Clow Valve Company.
ClowValve.com
4/27/18
Gate Valves
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED REVISE AND RESUBMIT REJECTED
BY DATE
ü
ü Submit cut sheet with spec. COR notes below
06/17/2022TimP
Clow Fire Hydrants
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE
FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED
REVISE AND RESUBMIT
REJECTED
BY DATE
A
HPHA™ adapter thread onto existing nozzle.
Made in USA from Forged 6061-T6 Aluminum, Hard Anodized to Mil-A-8625f, Type 3, Dark Gray, and
Tested for "High-Torque".
* ANY "SPECIAL THREAD" SIZE IS AVAILABLE AND CUT DIRECTLY INTO THE FORGING TO PROVIDE THE
LOWEST PROFILE AVAILABLE.
Note: 4" NH (NST) = 5.0 IO" ODM x 4 TPI, 4.5" NH (NST) = 5. 760" ODM x 4 TPI
"ODM" = Outside Diameter of the Male thread. "TPI" = Threads Per Inch
HPHA™ SPECIFICATION
The Permanent Hydrant Adapter threads onto the male nozzle and is secured permanently to the hydrant. A Storz spanner wrench is required for cap removal.
The Storz adapter shall have a hard anodized aluminum metal face seal and hard anodized aluminum Storz ramps and lugs. The adapter‘s finish shall be hardcoat anodized to Mil-A-8625, Type 3, dark gray. The adapter shall be made in USA from forged 6061-T6 aluminum and secured to the nozzle by (2) stainless steel set screws, inserted 180° apart. The female adapter shall contain a flat rubber gasket which seals against the male hydrant nozzle.
The blind cap shall have hard anodized aluminum Storz ramps and lugs, made of forged 6061-T6 aluminum. The cap shall be equipped with a suction seal. The cap shall be connected to the adapter or the hydrant with a 0.125" vinyl coated stainless steel aircraft cable. The cable shall be reflective to assist in locating the hydrant at night. The high torque cap requires a Storz spanner wrench for removal. Once installed, the Permanent Hydrant Adapter with cap extends less than 3" from the hydrant nozzle.
SPECIFY: HARRINGTON “HPHA”
Harrington, Inc.
HPHA™ Specifications
HPHA™ Harrington Permanent Hydrant Adapter™
Harrington Permanent Hydrant Adapter™: A Metal Face Storz
with Female Thread, secured to the male nozzle w/ (2) Set
Screws, includes Storz Cap with Reflective Aircraft Cable 2630 West 21st St., Erie, PA 16506 800.553.0078
4" STO RZ x Fem ale 5" STO RZ x Fem ale
H PH A40-40-XXX/C ap -4" sp ecial thread* H PH A50-40-XXX/C ap
H PH A40-40N H /C ap -4" N H -H PH A50-40N H /C ap
H PH A40-45N H /C ap -4.5" N H -H PH A50-45N H /C ap
5" Storz Adapter Seattle Thread
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED: NO EXCEPTIONS TAKEN REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022
Standon PiPe SuPPortS inc.
ADJUSTABLE PIPE SUPPORTS
SUPPORT STRAP THRD BASE EXTENSION
SIZE SIZE STUD PLATE PIPE REQ.
2” .375” x 2” 1” x 6” 4” x 6” x .25” 2” Sch. 40 7”
2.5” .375” x 2” 1” x 6” 4” x 6” x .25” 2” Sch. 40 7”
3” .375” x 2” 1” x 6” 4” x 6” x .25” 2” Sch. 40 7”
4” .50” x 2” 1” x 6” 8” x 8” x .25” 2” Sch. 40 7”
6” .50” x 2” 1” x 6” 8” x 8” x .25” 2” Sch. 40 7”
8” .50” x 2” 1” x 6” 8” x 8” x .25” 2” Sch. 40 7”
10” .50” x 2” 1” x 6” 8” x 8” x .25” 2” Sch. 40 7”
12” .50” x 2” 1” x 6” 8” x 8” x .25” 2” Sch. 40 7”
14” .625” x 3” 1½” x 6” 8” x 8” x .5” 3” Sch. 40 9.5”
16” .625” x 3” 1½” x 6” 8” x 8” x .5” 3” Sch. 40 9.5”
18” .75” x 4” 2” x 6” 8” x 8” x .5” 4” Sch. 40 10”
20” .75” x 4” 2” x 6” 8” x 8” x .5” 4” Sch. 40 10”
24” .75” x 4” 2” x 6” 8” x 8” x .5” 4” Sch. 40 10”
MINIMUM
DIST. TO
FLOOR
Standon PiPe SuPPortS inc.
2800 Taylor Way Bldg. 1
PO Box 247
Forest Grove, OR 97116
For product availability and ordering information on these
and other products offered by Standon Pipe Supports,
please call:
(503) 533-5256 or (877)693-0727
FAX (503) 533-5501
WWW.STANDON.NET
Standon Model S92 Saddle Support Product Specification Sheet
ALL MODELS TESTED TO OVER 10,000 POUNDS - COMPRESSIVE STRENGTH
MATERIAL -
Saddle strap: ASTM A36
Collar / base cups: ASTM A53 / ASTM A513 D.O.M. tubing
Thread stud: ASTM A36, rolled thread, grade ASTM A307
Base plate: ASTM A36 sheet steel
Optional Material - 100% 304L or 316L Stainless steel
FABRICATION -
All welds: 100% MIG welding, electrode E70XX
Saddle: Formed to ductile iron pipe radius
Optional neoprene liner available for IPS pipe
FINISH - All supports have corrosion resistant, electro-galvanized finish.
Hot dip galvanizing available - specify at time of order
OPTION- A neoprene liner is available to isolate pipe from saddle.
DIMENSIONS - (Note: call manufacturer for 30” through 48” support info.)
INSTALLATION -
To insure proper Support performance and stability; After final height adjustment is attained, apply tack welds to both support cups and extension pipe. Use E70XX electrode for welds. The base plate should be anchored to the floor with removable anchor bolts. If re-adjustment is required at a later date,
remove anchor bolts and rotate entire lower unit using collar nut. Re-anchor base plate.
STANDONMODELS92
3" S92 Standon Pipe Support
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
JMF Seamless Copper Tube
JMF COMPANY IS YOUR CONSOLIDATING SOURCE FOR copper tubing, line sets, copper fittings, push to fit, pex, ball valves, gas valves, plumbing valves, malleable fittings,
steel nipples, plastic fittings, brass threaded, brass nipples, flare & compression, gas connectors, water connectors, appliance kits, cord sets and MORE.
2735 62ND STREET COURT, BETTENDORF, IA 52722 • (800) 397-3739 • P (563) 332-9200 • F (563) 332-2799 • JMFCOMPANY.COM
JMF Seamless Copper Tube is preferred by plumbing, HVAC and refrigeration professionals who demand the highest quality, appearance, fill
rates and largest selection. For safety and reliability, pure copper tubing remains the #1 choice of professional plumbers installing potable
water systems. JMF stocks a complete array of popular types and sizes to satisfy the applications listed below. Visit our pricing page at www.
jmfcompany.com to view detailed product information on JMF Seamless Copper Tubing.
STANDARDS & SPECIFICATIONS
• Type K: ASTM B-88 Domestic Water, Service and Distribution,
Fire Protection, Solar, Fuel/Fuel Oil, HVAC, Snow Melting, and
Oxy C & C
• Type L: ASTM 8-88 Domestic Water, Service and Distribution,
Fire Protection, Solar, Fuel/Fuel Oil, HVAC, Snow Melting, and
Natural Gas
• Type M: ASTM B-88 Domestic Water, Service and Distribution,
Fire Protection, Solar, Fuel/Fuel Oil, HVAC, and Snow Melting
• Type DWV: ASTM B-306 Drain, Waste, Vent, HVAC, and Solar
• Utility Grade: Do-It-Yourself Market
• ACR: ASTM B-280 Air Conditioning, Refrigeration, Natural Gas
and Liquefied Petroleum (LP) Gas
• Refrigeration: ASTM B-280 Air Conditioning, Refrigeration,
Natural Gas and Liquefied Petroleum (LP) Gas
ASTM B-88 COPPER WATER TUBE, TYPE K, L M
• Copper tube (Alloy 12200) has been evaluated by
Underwriters Laboratories, Inc. To ANSI/NSF Standard 61 for
use in drinking water supplies of pH 6.5 and above. Drinking
water supplies which are less than pH 6.5 may require
corrosion control to limit leaching of copper into the
drinking water.
• Copper tube has been NSF classified by Underwriters
Laboratories, Inc. only to ensure that specific analyzed
samples met regulatory requirements.
ASTM B-819 COPPER TUBE FOR MEDICAL GAS SYSTEMS
• Manufactured tubes up to and including 2 1/8” are plugged
and charged with nitrogen following the cleaning operation
ASTM B-280 COPPER TUBE FOR AIR CONDIDTIONING AND
REFRIGERATION FIELD SERVICE
• Manufactured straight length hard tubes up to and including
2 1/8” are plugged and charged with nitrogen following the
cleaning operation. All tubes up to and including 8 1/8” are
manufactured to the cleanliness requirements of 0.0035
g/ft² maximum residue as required by B-280/B-819.
ASTM B-306 COPPER DRAINAGE TUBE (DWV)
MATERIALS
• Tubing is a minimum of 99.99% pure copper tube (Alloy 12200)
• Tube supplied meets or exceeds all applicable ASTM and
Industry standards
FEATURED ITEMS & APPLICATIONS1" K Soft Copper Tubing
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED: NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT REJECTED BY DATE
ü
06/17/2022
TimP
AWWA/CC TAPER THREAD INLET BY QUICK JOINT FOR COPPER OR PLASTIC TUBING (CTS) OUTLET
Vඉඔඞඍ
Sඑජඍ
Iඖඔඍග
Sඑජඍ
Oඝගඔඍග
Sඑජඍ
Vඉඔඞඍ
Lඍඖඏගඐ
Bඌඡ Oඝගඔඍග
Tඐකඍඉඌඛ
Aකච.
Wග. Lඊඛ
Pඉකග
Nඝඕඊඍක
✓ Sඝඊඕඑගගඍඌ
Iගඍඕ(ඛ)
3/4" 3/4" 3/4" 4-19/64" 3/4" Flare Copper 1.6 FB1000-3-Q-NL
1" 1" 1" 4-31/64" 1" Flare Copper 2.6 FB1000-4-Q-NL
1" 1" 1-1/4" 4-5/16" 1-1/4" Special Thread 3.4 FB1000-45-Q-NL
1-1/4" 1-1/4" 1-1/4" 5-21/32" 1-1/4" Special Thread 4.3 FB1000-5-Q-NL
1-1/2" 1-1/2" 1-1/2" 5-45/64" 1-1/2" Special Thread 5.4 FB1000-6-Q-NL
2" 2" 2" 7-1/16" 2" Special Thread 8.2 FB1000-7-Q-NL
The Ford Meter Box Company, Inc. P.O. Box 443, Wabash, Indiana U.S.A. 46992-0443
Phone: 260-563-3171 / Fax: 800-826-3487
Overseas Fax: 260-563-0167
www.fordmeterbox.com
Submitted By:
The Ford Meter Box Company considers the information in this submittal form to be correct at the time of publication. Item and option availability,
including specifications, are subject to change without notice. Please verify that your product information is current. Our standard warranty applies.
08/18/20
Ballcorp Corporation Stops - (FB1000-xx-Q-NL style)
SUBMITTAL INFORMATION
Note: Ford recommends using insert stiffeners with plastic pipe or tubing.
External Nut Stop
Molded NBR (Buna-N)
spring tip gasket provides
hydraulic seal
Stainless Steel Gripper Ring
Quick Joint Nut
Inlet
Solid one piece tee-head and stem
Dual EPDM O-rings in the stem
AWWA/CC Threads
Outlet
Body Outlet Threads
Molded EPDM rubber seat with
reinforcing ring supports the ball
FEATURES
• All brass that comes in contact with potable water conforms to AWWA Standard C800
(ASTM B584, UNS C89833)
• The product has the letters “NL” cast into the main body for lead-free identification
• Certified to NSF/ANSI Standard 61 and NSF/ANSI Standard 372 where applicable
• Brass components that do not come in contact with potable water conform to AWWA
Standard C800 (ASTM B62 and ASTM B584, UNS C83600, 85-5-5-5)
• Ends are integral or secured with adhesive to prevent unintentional disassembly
• 300 PSI working pressure
Due to design variations related to sizing, items may differ from images above.
EPDM O-ring
Fluorocarbon-coated brass ball
Length
1" Corp Stop THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE
FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT
REJECTED
BY DATE
ü
06/17/2022TimP
MALE IRON PIPE THREAD BY GRIP JOINT FOR COPPER OR PLASTIC TUBING (CTS)
Beveled EPDM rubber gasket
provides hydraulic seal
Length
Dඍඛඋකඑගඑඖ Lඍඖඏගඐ Aකච.
Wග. Lඊඛ
Pඉකග
Nඝඕඊඍක
✓ Sඝඊඕඑගගඍඌ
Iගඍඕ(ඛ)Mඉඔඍ Iකඖ Pඑඍ G.J. ඎක CTS
1/2" 3/4" 2-1/16" 0.5 C84-13-G-NL
3/4" 3/4" 2-1/4" 0.6 C84-33-G-NL
3/4" 1" 2-3/8" 0.7 C84-34-G-NL
1" 3/4" 2-3/8" 0.7 C84-43-G-NL
1" 1" 2-9/16" 0.8 C84-44-G-NL
1" 1-1/4" 2-1/2" 1.1 C84-45-G-NL
1" 1-1/2" 2-9/16" 1.8 C84-46-G-NL
1-1/4" 1-1/4" 2-9/16" 1.3 C84-55-G-NL
1-1/4" 1-1/2" 2-5/8" 1.7 C84-56-G-NL
1-1/2" 1-1/2" 3-1/4" 2.0 C84-66-G-NL
1-1/2" 2" 2-15/16" 2.2 C84-67-G-NL
2" 2" 3-1/4" 2.9 C84-77-G-NL
The Ford Meter Box Company, Inc. P.O. Box 443, Wabash, Indiana U.S.A. 46992-0443
Phone: 260-563-3171 / Fax: 800-826-3487
Overseas Fax: 260-563-0167
www.fordmeterbox.com
Submitted By:
The Ford Meter Box Company considers the information in this submittal form to be correct at the time of publication. Item and option availability,
including specifications, are subject to change without notice. Please verify that your product information is current.
03/23/17
Iron Pipe Thread
MIP Size
Nylon Washer Phosphor Bronze Gripper
Ring for axial restraint
G.J. Size
Grip Joint Coupling - (C84-xx-G-NL style)
SUBMITTAL INFORMATION
Grip Joint Nut
Note: Ford recommends insert stiffeners when using plastic pipe or tubing.
FEATURES
• All brass that comes in contact with potable water conforms to AWWA Standard C800
(ASTM B584, UNS C89833)
• The product has the letters “NL” cast into the main body for lead-free identification
• Certified to NSF/ANSI Standard 61 and NSF/ANSI Standard 372 where applicable
• Brass components that do not come in contact with potable water conform to AWWA
Standard C800 (ASTM B62 and ASTM B584, UNS C83600, 85-5-5-5)
• Ends are integral or secured with adhesive to prevent unintentional disassembly
1" Ford Coupling THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
FEATURES
• All brass that comes in contact with potable water conforms to AWWA standard C800 (UNS NO C89833)
• Brass components that do not come in contact with potable water conform to AWWA Standard C800 (ASTM B-62 and ASTM B-854, UNS NO C83600 - 85-5-5-5)
• The product has the letters “NL” cast into the main body for proper identification.
• Saddle Nuts hold the meter in place for tightening
• Bracing Eye is standard on all 70 Series Coppersetters • Tie Bar is standard for 21" and taller Coppersetter heights (74 Series)
• Double Purpose Union Swivels will accommodate male iron pipe threads or flare copper
• 1-1/8" Copper Risers provide more flow capacity
• All Ford Setters are assembled with lead-free solder
• Constructed of Type K Copper and conforms to ASTM B-88, Copper Alloy #122
DOUBLE PURPOSE UNION SWIVEL INLET AND OUTLET
ANGLE BALL VALVE BY ANGLE CHECK VALVE (1" METER)
The Ford Meter Box Company, Inc. P.O. Box 443, Wabash, Indiana U.S.A. 46992-0443 Phone: 260-563-3171 / Fax: 800-826-3487 Overseas Fax: 260-563-0167 http://www.fordmeterbox.com
Submitted By:
The Ford Meter Box Company considers the information in this submittal form to be correct at the time of publication. Item and option availability, including specifications, are subject to change without notice. Please verify that your product information is current.
08/03/11
70 Series Coppersetter - (VBH74-xxW-11-44-NL style)
SUBMITTAL INFORMATION
Height
Angle Ball
Valve Angle Check Valve
Bracing EyeD.P. SwivelInlet D.P. SwivelOutlet
1" meter
Coppersetter Part Number
Service Line Size
Tie Bar for 21" and Taller Heights
HEIGHT
(INCHES)
APPROX.
WT. LBS.CATALOG NUMBER SUBMITTED
ITEM(S)
10 9.2 VBH74-10W-11-44-NL12 9.3 VBH74-12W-11-44-NL15 9.6 VBH74-15W-11-44-NL18 9.9 VBH74-18W-11-44-NL
21 11.4 VBH74-21W-11-44-NL
24 11.8 VBH74-24W-11-44-NL
27 12.1 VBH74-27W-11-44-NL30 12.4 VBH74-30W-11-44-NL33 12.7 VBH74-33W-11-44-NL36 13.0 VBH74-36W-11-44-NL
39 13.3 VBH74-39W-11-44-NL
42 13.6 VBH74-42W-11-44-NL
INLET OUTLET1" D.P. Swivel 1" D.P. Swivel
VBH78-15W-11-44NL THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
Domestic Brass Nipples
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED: NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT REJECTED BY DATE
ü
06/17/2022
TimP
PROJECT APPROVAL STAMP
PROJECT:□ APPROVED
ADDRESS:□ APPROVED AS NOTED
ENGINEER:□ NOT APPROVED
SUBMITTAL DATA:REMARKS:
NOTES 1:
NOTES 2:
Revision: 8/2020
VALVE & MANUFACTURING MODEL LVVIP
FEATURES:
www.LansdaleValve.com
VERTICAL INDICATOR POST
Vertical Indicator Post indicates if valve is in the open or shut position. The indicator
post creates a way to operate a buried/inaccessible valve. Indicator post’s adjustment
range reaches 34.5” and can be easily adjusted on site. The wrench handle fits over
a “U” bracket on the barrel, and may be fixed with a padlock to secure the operating
wrench to the barrel. Ability to open left or right. UL Listed/FM Approved. Internally
and externally red epoxy coated RAL3000 for corrosion protection.
FIELD ADJUSTMENT:
• Remove the top section of the
upper barrel of the indicator post
• Cut the stem to the required length
and adjust the standpipe to match
up to the GROUNDLINE
• Set the OPEN and SHUT targets
for the appropriate valve size
• Re-attach the top section of the
upper barrel of the indicator post
NO.PART MATERIAL
1 Hex Cap Screw Carbon Stee lASTMA307B
2 Hex Nut Carbon Steel ASTMA307B
3 Crane Coupling Ductile Iron ASTMA536Gr.65-45-12
4 Cotter Pin Stainless Steel AISI304
5 Base Flange Cast Iron ASTMA 126 Class B
6 Hex Nut Carbon Steel ASTMA 307B
7 Hex Cap Screw Carbon Steel ASTMA 307B
8 Standpipe Carbon Steel ASTMA53
9 Stem 1 Square Carbon Steel AISI1045
10 Body Cast Iron ASTMA126 Class B
11 Locking Wrench Ductile Iron ASTMA 536 Gr.65-45-12
12 Target Carrier Nut Stainless Steel AISI304
13 Hex Cap Screw Carbon Stee lASTMA307B
14 Hex Nut Carbon Steel ASTMA307B
15 Hex Cap Screw Carbon Steel ASTMA307B
16 Target Cast Aluminum
17 Window Glass Plexiglass
18 Gasket PTFE
19 Operating Nut Bronze ASTMB62C83600
20 Top Section Cast Iron ASTMA126 Class B
21 Snap Ring Stainless Steel AISI1066
22 Plug Malleable Iron
23 Square Nut Carbon Steel ASTMA307B
24 Hex Cap Screw Carbon Steel ASTMA307B
Order Length Min. Max.
A 18.25”39.50”
B 36.00”60.50”
C 57.00”81.50”
D 78.00”102.50”
E 99.00”123.50”
F 120.00”144.50”
G 148.50”168.00”
Post Indicator (D)
lansdalevalve.com
800-543-4194 info@brecco.com brecco.com 21-001-04-2021ALL THREAD ROD
• Size Range: Stocking sizes 1/4" through 1 ½” in six-, 10- and
12-foot lengths with other foot lengths available as furnish-to-order
• Material: Stainless steel Type 304 and 316 or carbon steel
black and electro-galvanized
• Threads: National Coarse (USS)
• Maximum Temperature: 450 F for zinc-plated; 650 F
for stainless steel
• Approvals: Products comply with MSS SP-58
• Ordering: Specify rod diameter, length, finish and material
Now Available
in Stainless Steel
Now Stocked in our Atlanta Distribution Center,
available in these states!
3/4X10 All Thread Rod
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
lansdalevalve.com
800-543-4194 info@brecco.com brecco.com
NOW INSTOCK!20-003-02_10-2020• Meets or exceeds all applicable ASTM and ANSI standards
• Stocked from 1/8" through 6" diameters
• 100% pressure tested
• UL and FM approved
Material: ASTM A 197 CupolaDimensions: ANSI B 16.3, B 16.4, B 16.39Union dimensions: ASME B16.39TThreads: ANSI/ASME B 1.20Class: 150Tensile strength: 28.4 kg/mm (minimum)Elongation: 5% minimumZinc coating: ASTM A153
Globally sourced
MALLEABLE FITTINGS
CLASS 150
Dimensions: ASTM A733Threads: NPT per ASME B1.20.1Material: ASTM A53, Sch 40 Welded Steel PipeFinish: Black or hot dip galvanizedSpecials available upon request: TxG, GxG, GxPE, BxB
Globally sourced
Note: Ready-cut black nipples available 1/4" to 4" up to 96" long
Galvanized available in 1/4" to 4" and 6" to 96" long
WELDED STEEL PIPE NIPPLES
Galvanized Fittings Galvanized Nipples
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
LANSDALE BALL VALVE WITH SS HANDLE
MODEL LVBVSST
lansdalevalve.com
800-543-4194 info@brecco.com brecco.com
NOW INSTOCK!22-001-03_02-2022FEATURES:
• Lead free
• 600 psi
• SS 304 handle
• Full port
AVAILABILITY:
1/2", 3/4", 1", 1-1/4", 1-1/2" and 2"MODEL LVBVSST
LANSDALE BALL VALVE WITH DRAIN
MODEL LVBVDR
FEATURES:
• Lead free
• 600 psi
• Full port
AVAILABILITY:
1/2", 3/4" and 1"MODEL LVBVDR
Brass Ball Valves
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
FEATURES:
FLANGE PACKS
Flange Packs include everything needed to make-up a flanged assembly.
Suitable for use in all flanged connection in fire sprinkler systems. Each kit
includes one ⅛” red rubber ring gasket and the correct number of plated
hex head bolts and nuts per flange.
SPECIFICATIONS:
Each kit contains one ⅛” thick red rubber ring gasket and the
following A307 (Grade 2) plated nuts and bolts according to size.
Temp Range: Max. - 170F (77C)
Min. - -20F (-29C)
MODEL LVFP
SIZE NO. OF
BOLTS BOLT SIZE CASE
QTY
2” 4 ⅝” x 2½”10
2½”4 ⅝”x 3”10
3”4 ⅝” x 3”10
4”8 ⅝” x 3”10
5”8 ¾” x 3½”6
6”8 ¾” x 3½”6
8”8 ¾” x 3½”6
10”12 ⅞” x 4”5
12”12 ⅞” x 4”5
PROJECT APPROVAL STAMP
PROJECT:□ APPROVED
ADDRESS:□ APPROVED AS NOTED
ENGINEER:□ NOT APPROVED
SUBMITTAL DATA:REMARKS:
NOTES 1:
NOTES 2:
Revision: 9/2021
www.LansdaleValve.com
Zinc Plated Nut/Bolt Packs
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
PROJECT APPROVAL STAMP
PROJECT:□ APPROVED
ADDRESS:□ APPROVED AS NOTED
ENGINEER:□ NOT APPROVED
SUBMITTAL DATA:REMARKS:
NOTES 1:
NOTES 2:
Revision: 4/2020
VALVE & MANUFACTURING
MODEL LVPIVSS
FEATURES:
P.I.V (WALL OR VERTICAL POST)
TAMPER SWITCH
• Weight: .1.323 lbs
• Temperature Rating: -40ºF - 140ºF
• Enclosure:
Cover: Die Cast
Finish: Red Powder Coat
Base: Die Cast
All parts have corrosion resistant finishes
• Cover Tamper:
Tamper Resistant Screws
Cover Tamper Switch Available
33amps/5amps at 125/250VAC
• Contact Ratings:
Two sets of SPDT
10amps at 125/250VAC. 2.5 Amps30VDC resistive
• Conduit Entrances: One knockout and one hole for ½” conduit provided
• Service Use: NFPA 13, 13D, 13R, 72
• UL/ULC Listed/FM Approved
Dimensions/Inches
Tamper Switch
VALVE & MANUFACTURING
CLASS 125 lbs.
Lead Free products contain less than .25% weighted average lead content on wetted surfaces.
LEAD FREE BRASS COMPOSITION
COPPER TIN LEAD ZINC
Min.87.00%4.00%0.00%2.00%
Max.91.00%6.00%0.10%4.00%
IRON NICKEL ANTIMONY PHOSPHORUS
Min.0.00%0.00%0.00%0.00%
Max.0.30%1.00%0.25%0.05%
SULFUR ALUMINUM SILICON BISMUTH
Min.0.00%0.00%0.00%1.70%
Max.0.08%0.005%0.005%2.70%
BRASS FITTINGS
Revision: 4/2020
www.LansdaleValve.com
• Approved to ANSI/NSF 61-4 California AB 1953
• Meets Federal State Drinking Water Act, Lead Free Requirement
• Brass fittings conform to AWWA C800
• Brass castings conform to ASTM B584, UNS Alloy C89833
• Brass fittings dimensions conform to ASME B16.15
• NPT threads on all fittings conform to ASME B1.20.1
• Brass unions conform to specification A-A-59617
• Manufacturing facilities are ISO 9001:2008
FEATURES:
Brass Fittings
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH
DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED
REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
RED RUBBER GASKET
SUBMITTAL SPECIFICATIONS
GASKETS MEETS THE PRESSURE RATINGS, DRILLING AND DIMENSIONS OF ANSI/ASME B16.21
TECHNICAL DATA
MANUFACTURES STYLE COLOR BINDER TEMP
MAX
HARDNESS
SHORE A
TENSILE STRENGTH
ASTM D412
AMERICAN BILTRITE AB-619 RED SBR 180° 75 +/-5 600
AVAILABILITY
Full Face Ring 1/16” 1/8” 1/4”
GENERAL DESCRIPTION: An economical, non-oil resistant compound that resists flow under
compression. Offers moderate to good performance against low pressure and good aging, abrasion and
tear resistance. Easily conforms to uneven flange surfaces.
**Domestically manufactured in the USA**
Irrigation Double Check
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
Irrigation Double Check
THIS DOCUMENT HAS BEEN REVIEWED
FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN
REVISE AS NOTED REVISE AND RESUBMIT REJECTED
BY DATE
ü
06/17/2022TimP
SUBMITTAL SHEET
This specification is provided for reference only. Apollo reserves the right to change any portion of this specification without notice and without incurring obligation to make such changes to Apollo products previously or subsequently sold.Most current information available at apollovalves.com.
(704) 841-6000apollovalves.com
FLOW CURVES DC4A
1/2"
3/4"
7.5 fps 1/2"7.5 fps 3/4"
2
4
6
8
10
12
14
16
18
20
010203040
RATE OF FLOW (GPM)PRESSURE LOSS (PSI) DC4A
1"1 1/4"
7.5 fps 1" 7.5 fps 1 1/4"
2
4
6
8
10
12
14
16
18
20
0102030405060708090100 110
RATE OF FLOW (GPM)PRESSURE LOSS (PSI) DC4A
1 1/2"2"
7.5 fps 1 1/2" 7.5 fps 2"
2
4
6
8
10
12
14
16
18
20
020406080100 120140 160180 200 220240
RATE OF FLOW (GPM)PRESSURE LOSS (PSI) Double Check Valves - A Series
DC4A & DCLF4A
LEAD FREE
SS1380 © 10/18 Page 2 of 2
SCOPE
These specifi cations set forth the minimum acceptable design
criteria and performance requirements for Compound-type
cold water meters including the following potential service
applications and general considerations:
• Intended where a wide fl ow range is anticipated
• Measurement of water usage for critical billing applications
• Measurement intended for typical commercial and
industrial applications requiring lower fl ow sensitivities
• Measurement of low fl ow usage below OMNI T2 Meter
threshold levels
• Measurement of constant low to medium fl ows up to high
fl ow usage
CONFORMANCE TO STANDARDS
The meter package shall meet or exceed all requirements of
ANSI/AWWA Standard C701 and C702 for Class II compound
and turbine meter assemblies. Each meter assembly shall
be performance tested to ensure compliance.
The meter package shall meet or exceed all requirements of
NSF/ANSI Standard 61, Annex F and G.
MAINCASES
The meter maincase shall be of epoxy coated ductile iron
composition. The epoxy coating shall be provided as stan-
dard fusion-bonded and adhere to NSF for non-lead regula-
tion compliance.
PERFORMANCE
The meter assembly shall have performance capability of
continuous operation up to the rated maximum fl ows as
listed below without affecting long-term accuracy or causing
any undue component wear. The meter assembly shall also
provide a 25% fl ow capacity in excess of the maximum fl ows
listed for intermittent fl ow demands. Maximum headloss
through the meter / strainer assembly shall not exceed those
listed in the following table per meter size.
OPERATING CHARACTERISTICS
Meter
Size
Low Flow
(95% Min.)
Operating
Range
(98.5 - 101.5%)
Intermittent
Flows
(98.5 - 101.5%)
Pressure Loss
(Not to Exceed)
1-1/2” .25 GPM .5 to 160 GPM 200 GPM 6.9 PSI @ 160 GPM
2” .25 GPM .5 to 160 GPM 200 GPM 4.3 PSI @ 160 GPM
3” .5 GPM 1.0 to 400 GPM 500 GPM 3.2 PSI @ 400 GPM
4” .75 GPM 1.5 to 800 GPM 1000 GPM 6.4 PSI @ 800 GPM
6” 1.5 GPM 3.0 to 1600 GPM 2000 GPM 5.5 PSI @ 1600 GPM
8” 2.5 GPM 4 to 2700 GPM 3400 GPM 4 PSI @ 2700 GPM
10” 3.5 GPM 5 to 4000 GPM 5000 GPM 4.5 PSI @ 4000 GPM
MEASURING CHAMBER
The measuring chamber shall consist of a measuring
element, removable housing, and all-electronic register.
The measuring element shall be mounted on a horizontal,
stationary stainless steel shaft with sleeve bearings and
be essentially weightless in water. The measuring element
comes integrated with the advanced Floating Ball Technology
design. The measuring chamber shall be capable of
operating within the above listed accuracy limits without
calibration when transferred from one maincase to another
of the same size. The measuring shall be so confi gured to
capture all fl ows as specifi ed above, without the requirement
of an automatic valve.
DIRECT MAGNETIC DRIVE SYSTEM
The direct magnetic drive shall occur between the motion
of the measuring element blade position and the electronic
register. The OMNI direct drive system with Floating Ball
Technology is designed to extend service life, enhance
low fl ow sensitivity and provide extended fl ow capacity and
overall accuracy of the meter assembly. Any and all additional
intermediate, magnetic or mechanical, drive couplings are
not acceptable.
ELECTRONIC REGISTER
The meter’s register is all-electronic and does not contain any
mechanical gearing to display fl ow and accurate totalization.
The electronic register includes the following patial list of
features:
• AMR resolution units fully programmable
• Pulse output frequency fully programmable
• Integral data logging capability
• Integral resettable accuracy testing feature
• Large, easy-to-read LCD display
• 10-year battery life guarantee
1-1/2”, 2”, 3”, 4”, 6”, 8” and 10” Sizes
SP-W-OMC-00-00-0611-04-A
OMNITM C2
Specifi cations
8601 Six Forks Road, Suite 700
Raleigh, NC 27615
1-800-638-3748
www.sensus.com/water
© All products purchased and services performed are subject to Sensus’ terms of sale, available at either; http://na.sensus.com/TC/TermsConditions.pdf or 1-800-METER-IT. Sensus reserves the right to modify
these terms and conditions in its own discretion without notice to the customer.
This document is for informational purposes only, and SENSUS MAKES NO EXPRESS WARRANTIES IN THIS DOCUMENT. FURTHERMORE, THERE ARE NO IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION, WARRANTIES AS TO FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. ANY USE OF THE PRODUCTS THAT IS NOT SPECIFICALLY PERMITTED HEREIN
IS PROHIBITED.
MAXIMUM OPERATING PRESSURE
The meter assembly shall operate properly without leakage,
damage, or malfunction up to a maximum working pressure
of 200 pounds per square inch (psig).
STRAINERS
The meter strainer shall be integral and cast as part of
the meter’s maincase. The strainer’s screen shall have a
minimum net open area of at least two (2) times the pipe
opening and be a V-shaped confi guration for the purpose
of maintaining a full unobstructed fl ow pattern. The strainer
body shall be a coated ductile iron fusion-bonded epoxy
identical to that of the meter’s maincase. All fasteners shall
be stainless steel capable of maintaining the following static
pressure ratings and physical dimensions:
Meter
Size
Maximum Working
Pressure
Centerline to
Strainer Base
Overall Length
(Not to Exceed)
1-1/2” 200 PSIG 2-5/16 INCHES 13 INCHES
2” 200 PSIG 2-5/16 INCHES 15-1/4 INCHES
3” 200 PSIG 4-1/8 INCHES 17 INCHES
4” 200 PSIG 4-3/4 INCHES 20 INCHES
6” 200 PSIG 5-3/4 INCHES 24 INCHES
8” 200 PSIG 6-3/4 INCHES 30-1/8 INCHES
10” 200 PSIG 8-1/2 INCHES 41-1/8 INCHES
STRAIGHTENING VANES
A straightening vane assembly is mandatory and shall be
positioned directly upstream of the measuring element. The
straightening vane assembly shall be an integral component
of the measuring chamber.
CONNECTIONS
Flanges for the 1-1/2” and 2” size meter assemblies shall be
of the 2-bolt oval fl ange confi guration. The 3”, 4”, 6”, 8” and
10” size meter assemblies shall have fl anges of the Class
125 round type, fl at faced and shall conform to ANSI B16.1
for specifi ed diameter, drilling and thickness.
CERTIFICATIONS AND MARKINGS
All sizes of meter packages shall display the sizes, model,
manufacturer name, and direction of fl ow. Such display shall
be cast on the side of the meter maincase.
GUARANTEE AND MAINTENANCE
PROGRAM
Meters shall be guaranteed against defects in material
and workmanship for a period of one (1) year from date
of shipment. In addition, the meter supplier shall submit
nationally published literature clearly outlining its factory
maintenance program and current price schedule covering
complete measuring chamber exchange.
INTENT
Subject meter specifi cations are designed to establish
minimum guidelines for selecting an extremely critical
metering device. Areas of concern to be evaluated in the
selection process include, but are not limited to, ease of
installation, operational features and benefi ts, readability
and future system maintenance expense. A design, which
refl ects longevity of proper operation in all elements and high
degree of sustained accuracy within the entire range of the
meter assembly, is to be considered mandatory. Enhanced
accuracy levels and performance are desired and will not be
compromised.
RECOMMENDATION
Sensus OMNI C2 Meter
SP-W-OMC-00-00-0611-04-A
Page 2 of 2
3" OMNI Meter
opauburn.com
Items Shown Are Subject To Change Without Notice
Issue Date: August 2012 17 ©1970-2012 Oldcastle Precast, Inc.
577-LA
Mailing Address
PO Box 588
Auburn, WA 98071
Phone: 800-892-1538
Fax: 253-735-4201
Email: opauburn@oldcastle.com
Delivering Reliability
FOR DETAILS, SEE REVERSE >> Non Skid Covers Available
OPTIONAL COVER SECTIONS
VAULT
No. 577-BL
No. 57-2-33F
COVER
Meter Vault
THIS DOCUMENT HAS BEEN REVIEWED FOR GENERAL COMPATIBILITY WITH DESIGN CONCEPT AND THE FOLLOWING IS NOTED:
NO EXCEPTIONS TAKEN REVISE AS NOTED REVISE AND RESUBMIT REJECTED
BY DATE
SECTION AA
A
PLAN VIEW
A
END VIEW
opauburn.com
17.1 ©1970-2012 Oldcastle Precast, Inc.
577-LA
Delivering Reliability
SCALE: 3/8” = 1’-0”
Meter Vault 5'-11"
Selection Guide
6
Leaders in Sealing Integrity
WITH EPDM SEAL ELEMENTS
WITH EPDM SEAL ELEMENTS
EPDM (BLACK)
MODEL “C” LINK-SEAL® MODULAR SEAL
Suitable for direct ground burial, normal
atmospheric conditions, and conditions with
occasional or periodic water contact. Provides
electrical isolation where cathodic protection is
required.
Type: Standard
Seal Element: EPDM (Black)
Pressure Plates: Reinforced Nylon Polymer
Bolts & Nuts: Carbon steel with corrosion
inhibiting proprietary organic coating..
Temp. Range: -40˚ - +250˚F (-40˚ - +121˚C)*
MODEL “S-316” LINK-SEAL® MODULAR SEAL
For chemical processing & waste water treatment.
High level of water-resistance, resistant to most
inorganic acids and alkalis, and most organic
chemicals (acetone, alcohol, ketones).
Type: Stainless
Seal Element: EPDM (Black)
Pressure Plates: Reinforced Nylon Polymer
Bolts & Nuts: 316 Stainless Steel
Temp. Range: -40˚ - +250˚F (-40˚ - +121˚C)*
* = Sustained operation near temperature limits may affect life expectancy.
WITH NITRILE SEAL
ELEMENTS
NITRILE (GREEN)
MODEL “O” LINK-SEAL® MODULAR SEAL
Nitrile rubber is resistant to oils, fuel and many
solvents (gasoline, motor oil, kerosene, methane,
jet fuel, hydraulic fluid, water, etc.).
Type: Oil Resistant
Seal Element: Nitrile (Green)
Note: Not U.V. Resistant
Pressure Plates: Reinforced Nylon Polymer
Bolts & Nuts: Carbon steel with corrosion
inhibiting proprietary organic coating.
Temp. Range: -40˚ - +210˚F (-40˚ - +99˚C)*
MODEL “OS-316” LINK-SEAL® MODULAR
SEAL
Combination of oil resistant rubber and stainless
steel hardware.
Type: Oil Resistant
Seal Element: Nitrile (Green)
Note: Not U.V. Resistant
Pressure Plates: Reinforced Nylon Polymer
Bolts & Nuts: 316 Stainless Steel
Temp. Range: -40˚ - +210˚F (-40˚ - +99˚C)*
* = Sustained operation near temperature limits may affect life
expectancy.
EPDM (BLUE)
Low Durometer
MODEL “L” LINK-SEAL® MODULAR SEAL
Low Durometer EPDM specifically designed
for use with fragile pipe and tubing. Suitable
for direct ground burial, normal atmospheric
conditions, and conditions with occasional
or periodic water contact. Provides electrical
isolation where cathodic protection is required.
Type: Standard
Seal Element: EPDM (Blue)
Pressure Plates: Reinforced Nylon Polymer
Bolts & Nuts: Carbon steel with corrosion
inhibiting proprietary organic coating..
Temp. Range: -40˚ - +250˚F (-40˚ - +121˚C)*
MODEL “LS-316” LINK-SEAL® MODULAR
SEAL
Low Durometer EPDM specifically designed for
use with fragile pipe and tubing. For chemical
processing & waste water treatment. High level
of water-resistance, resistant to most inorganic
acids and alkalis, and most organic chemicals
(acetone, alcohol, ketones).
Type: Stainless
Seal Element: EPDM (Blue)
Pressure Plates: Reinforced Nylon Polymer
Bolts & Nuts: 316 Stainless Steel
Temp. Range: -40˚ - +250˚F (-40˚ - +121˚C)** = Sustained operation near
temperature limits may affect life
expectancy.
LINK-SEAL® Modular Seal Model Properties
PROUDLYMADE IN THEUSA
Link Seals
From: Michael Sippo <MSippo@Rentonwa.gov>
Sent: Thursday, June 23, 2022 8:43 AM
To: Tim Prusa
Cc: Michelle Freeman; Brad Stocco
Subject: RE: Solera - Water materials review
Follow Up Flag: Follow up
Flag Status: Flagged
Good morning Tim,
Please see my responses below:
MICHAEL S. SIPPO, Civil Engineer III
City of Renton | CED | Development Engineering Division
1055 S Grady Way | 6th Floor | Renton, WA 98057
Virtual Permit Center | Online Applications and Inspections
(425) 430-7298| msippo@rentonwa.gov
From: Tim Prusa <tim.prusa@kpff.com>
Sent: Tuesday, June 21, 2022 9:53 AM
To: Michael Sippo <MSippo@Rentonwa.gov>
Cc: Michelle Freeman <michelle.freeman@kpff.com>; Brad Stocco <BStocco@Rentonwa.gov>
Subject: RE: Solera - Water materials review
Thanks for the clarification Michael. We will provide a copy of the reviewed submittal.
Attached are submittals with requested deviations from the contractor.
· Valve box (not Rich-Seattle or Olympic Foundry per COR 330.1) Approved. Valve box is
on the City’s approved material list.
· XR501 Coupling for Connection to Existing at NE 12th Street (not noted in COR
details) Not approved, Use long body DI sleeve in lieu of a flange coupling adaptor.
· Post Indicator and Tamper Switch (not noted in COR details) PIV and switch is
private. Confirm ok with Renton Regional Fire Authority
· 3” OMNI Meter (please confirm equal to requested compound meter in COR
320.4) Approved. Omni C2 is on City’s approved materials list
· Link Seal (for connections to meter vault in lieu of welded steel collar in COR 320.4) See
Snippet below. Link seal should meet the requirements on the detail.
CAUTION: This email originated from outside the City of Renton. Do not click links, reply or
open attachments unless you know the content is safe.
Tim Prusa
Civil Design Engineer
D 206.926.0586 O 206.622.5822
tim.prusa@kpff.com
From: Michael Sippo <MSippo@Rentonwa.gov>
Sent: Tuesday, June 21, 2022 8:12 AM
To: Tim Prusa <tim.prusa@kpff.com>
Cc: Michelle Freeman <michelle.freeman@kpff.com>; Brad Stocco <BStocco@Rentonwa.gov>
Subject: RE: Solera - Water materials review
Good morning Tim,