HomeMy WebLinkAbout68F.
B-21,.3(14) SIGNAL SYSTEMS (SLI'PLEMENTAL SECTION)
ALL SIGNAL CONXCTORS SHALL BE STRANDED C&PPER AND SHAI-L RAVE 600 VOLT TH lWSULATION AND BE OF THE
SIZES NOTED ON THE PLANS. ALL MULTI-CONIXICTORS I FOR THE SIGNAl- SYSTEM SHALL CONFORM TO
DIVISION 9-29.3 AND SIALL BE OF THE SIZES NOTED ON THE SIGNAL WIRING SCHEDULE AND WIRING DIAGRAM.
ALL STRANDED WIRES TERMINATED AT A TERMINAL BLOCK SHALL HAVE AN OPEN END, CRIMP STYLE SODERLESS
TERMINAL CONNECTOR, AND ALL SOLID WIRES TERMINATED AT A TERMINAL BLOCK SMALL HAVE AN OPEN END
SOk-DERED TERMINAL CONNECTOR. ALL TERMINALS SHAJLL BE INSTALLED WITH A TOOL DESIGNED FOR THE
INSTALLATION OF THE CORRECT TYPE OF CONNECTOR AND CRIMPING WITH PLIERS, WIRE CUTTERS, E-TC., WILL
NOT BE ALLOWED. ALL WIRING INSIDE THE CONTROLLER CABINF-T SHALL BE TRIMMED AND CABLED TOGETHER TO
MAKE A NEAT, CLEAN APPEARING INSfALLATION. NO SPLICING OF ANY TRAFFIC SIGNAL CONDUCTOR SHALL BE
PERMITTED LNLESS OTHERWISE INDICATED ON TI-E PLANS. ALL CONDUCTOR RUNS SMALL BE ATTACHED TO
APPROPRIATE SIC40L TERMINAL BOARDS WITH PRESSURE TYPE BINDING POSTS. THE ONLY EXCEPTIONS SHALL BE
THE SPLICES FOR DETECTOR LOOPS AT THE NEAREST JUNCTION BOX TO THE LOOPS.
8-20.3(14)D TEST FOR INDJCTION LOOPS AND LEAD --IN CABLES (ADDITIONAL SECTION)
THE CONTRACTOR SHALL KFEP RECORDS OF FIELD TESTING AND SHALL FURN191 THE ENGINEER WITH A COPY OF
THE RESULTS.
B-20.3(14)E SIGNAL STANDARDS (REPLACEMENT SECTION)
rHE CONTRACTOR SHALL F'LFNISH AND INSTALL TRAFFIC SIGNAL STANDARDS IN ACCORDANCE WITH THE METHODS
AND MATERIALS NOTED IN THE CONTRACT PLANS AND THESE SPECIFICATIONS.
ALL POLE DIMENSIONS AND ORIENTATIONS WILL BE VERIFIED BY THE ENGINEER PRIOR TO FABRICATION.
ALL ENTRANCES REQUIRED FOR POLEMO�TED SIGNAL HEADS, CABINETS, SIGNS, PEDESTRIAN PUSH BUTTON
ASSEMBLIES, ETC. SMALL BE FIELD DRILLED.
8-20.4 MEASLlREMENT (RE]-ACEMENT SECTION)
MEA-cUIEMEW FOR TRENCH AND BACKFILL WILL BE BY THE LINEAR FOOT.
W-A-Si-REMENT FOR SELECT TRENCH BACKFILL WILL BE BY THE TON.
MEAaAREME-NT FOR SIGNAL STANDARDS AND SIGNAL CONX)CTORS WILL BE BY PER EACH AND PER LINEAR FT/LUMP
Sum.
MEAS-1REMENT FOR FOUNDATIONS - CONCRETE, WILL BE BY THE UNIT FOR EACH TYPE SPECIFIED, COMPLETE IN
PLACE.
MEASLIREMENT FLA CONDUIT WILL BE BY THE LINEAR FOOT.
MEASUREMENT FOR JUNCTION BOXES. WILL BE BY THE UNIT FOR EACH TYPE SPECIFIED. COMPLETE IN PLACE.
f,EASUREMENT 'R LIGHT STANDARDS, WILL BE BY THE UNIT PER EACH, COMPLETE IN PLACE.
8-20.5 PAYMENT (,REPLACEMENT SECTION)
PAYMENT WILL BE KADE UNDER:
1) -TRENCH AND BACKFILL, _ WIDE- -DEEP�, per Linear Foot.
2) -SELECT TRDICH BACKFILL-, Per To�.
THE UNIT CONTRACT PRICE FOR TRENCH NIC BACKFILL PER LINEAR FOOT SHALL BE FULL COMPENSATION
FOR EXCAVATING, LOADING, HAULING AND OTHERWISE DISPOSING OF THE WASTE MATERIALS, FOR
BACK'ILLING ALND TAMPING BACKFILL HATERIALL AND FOR THE RESTORATION OF THE TRENCH AS SHOWN ON
THE PLANS OR AS DIRECTED BY THE ENGINEER ALL IN ArrORDANCE WITH THESE SPECIAL PROVISIONS
AtU THE STANDARD PLANS AND SPECIFICATIONS.
Supple�ental Specifications
(Rev 05/01/86) Page 46