HomeMy WebLinkAbout62-29.10 CONTINUED
LUMINAIRES SHALL HAVE A CAST-ALUMINUFA HOUS-ING PROVIDING FOR A SLIP -FITTER TYPE MOUNTING AND CAPABLE
OF ADAPTING TO A 2-INCH DIAMETER PIPE I-ENON-
LUv4INAIRES SHALL BE OF THE COBRA HEAD STYLE WITH AN OVATE REFRACTOR (DROPPED LENS) FOR ARTERIALS
AND A CLEAR FLAT LENS FOR RESIDENTIAL ROADWAY APPLICATIONS.
THE LUNINA-IRE SHALL INCLUCAE THE POWER DOOR FEATLIF-7.
THE LUMINAIRE SHALL HAVE A GASKET BETWEEN REFRqCTOR AND REFLECTOR. A GA-SKET OR FILTER MATERIAL
SHALL BE PLACED BETWEEN THE LAW SOCKET AND THE REFLECTOR.
THE mANLFACTURER-S NAME OR SYMBOL SHALL BE CLEARLY MARKED ON EACH LUMINAIRE.
EA(>, LUNINAIRE SHALL HAVE A WEATHER-RESISTAXT, ANSI -APPROVED DECAL ATTACHED TO THE BALLAST HOUSING
SO AS TO BE READILY VISIBLE FROM THE GROUND. THE DECAL SHALL BE APPROXIMATELY THREE INCHES SQUARE
AND "HE LEGEM SHALL BE A MINIMUM OF TWO INCHES IN HEIGHT. THE DECAL SHALL BE GOLD IN COLOR WITH
LAW WATTAGS INDICATED BY THE FOLLOWING NUMERICAL LEGEND:
7 FOR 70 WATTS 25 FOR 250 WATTS
10 FOR 100 WATTS 31 FOR 310 WATTS
15 FOR 150 WATTS 40 FOR 400 WATTS
17 FOR 175 WATTS 70 FOR 700 WATTS
20 FOR 200 WATTS XI FOR 1,000 wAT
ALL LUMINATRES 94ALL HAVE THEIR COMPONENTS SECURED TO THE LUMINAIRE FRAME WITH STAINLESS STEEL
MOUNTING HAR01-1ARE (NUTS, BOLTS, WASHEYLS, HINGES, ETC.). THE FOUSING, COMPLETE WITH INTEGRAL
BALLAST, SHALL BE WEATHER -TIGHT.
9-29.11 CONTROL EQUIPMENT (REPLACEMENT SECTION)
UNLESS SPECIFIED OTHERWISE, ILLUMINATION CIRCUITS SHALL BE CONTROLLED BY A COMBINATION OF
PHOTOFIECTRIC CONTROLS AND LIGHTING CONTACTORS AS NOTED IN THE CONTRACT.
9-29.11(l) TIME CLOCK CONTROLS - DELETE
9-29.11(2) PHOTOELECTIC CONTROLS (REPLACEMENT SECTION)
PHOTOELECTRIC CONTROLS SHALL BE PLUG-IN DEVICES, RATED TO OPEKATE ON 120 VOLTS, 60 Hl. THE PHOTO-
CELL SHALL BE A SOLID STATE DEVICE WITH STABLE TURN -ON VALUES IN THE TEMPERATURE RANGE - 55 DEGREES
C TO .70 DEGREES C. THE PHGTO-CELL SHALL BE MOUNTED EXTERNALLY ON TOP OF THE LUMINAIRE. IN A
CONTACTOR-COINTROL-LED SYSTEM, THE PHOTO -CELL TO CONTROL THE SYSTE)4 94ALL BE MOUNTED ON THE LLE41NAIRE
NEAREST TO THE SLRVICE/CONTACTOH CABINET. THE PHOTO -CELL SHALL BE CAPABLE OF SWITCHING 1,000 WATTS
OF INCANDESCENT LOAD 'ON" AS MIN.
9.29.12(l) ILLUMINATION CIRCUI! SFLI C_ELjE9!L �NTSECT ION)
ALL SPLICES AND TAPS SHALL BE MADE USING SOLDERLESS CRIMP CONNECTORS ON UNDERGROUND CIRCUITS TO
SECURELY JOIN THE WIRES BOTH MECHANICALLY AND ELECTRICALLY. ALL SPLICES SHALL ENF`l_OY EPDXY RESIN
FILLED IN CLEAR PLASTIC HOLDS TO FORM A WATER TIGHT SEAL. ALL MATERIAL USED IN THE SPLICE KIT
SHALL BE COMPATIBLE WITH THE WIRE AND ITS INSULATION AS USED IN THE LIGHTING SYSTEN.
9-29.13 TRAFFIC SIGNAL CONTROLLERS (REPLACEMENT SECTION)
THE UNIT %LALL OPERATE ON 120 VOLT, 60 CYCLE, SINGLE PHASE ALTERNATING CURRENT AND SHALL USE THE
POWER LINE FREQUENCY AS A TIME BASE. THE TRAFFIC SIGNAL CONTROLLER SHALL MEET THE REQUIREMENTS OF
THE NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) STANDARD PUBLICATIONS.
jul Suppleme�tal Specifications
TF__ (Rev 05/01/86) Page 54