Loading...
HomeMy WebLinkAboutORD 4843Amends ORD 4629 & 4720 CITY OF RENTON, WASHINGTON Amended by Ord: 5357 ORDINANCE NO. 4843 AN ORDINANCE OF THE CITY OF RENTON, WASHINGTON, AMENDING SECTIONS 4-4-100.B AND H OF CHAPTER 4, PROPERTY DEVELOPMENT STANDARDS, OF TITLE 4 (DEVELOPMENT REGULATIONS), OF ORDINANCE NO. 4260 ENTITLED "CODE OF GENERAL ORDINANCES OF THE CITY OF RENTON, WASHINGTON" BY AMENDING DOWNTOWN IDENTIFICATION SIGN REGULATIONS. THE CITY COUNCIL OF THE CITY OF RENTON, WASHINGTON, DO ORDAIN AS FOLLOWS: SECTION I. Section 4-4-100.B.6.d of Chapter 4, Property Development Standards, of Title 4 (Development Regulations), of Ordinance No. 4260 entitled "Code of General Ordinances of the City of Renton, Washington" is hereby amended to read as follows: d. Construction Signs: i. Construction Advertising: One temporary sign per street frontage, not exceeding 32 square feet in area on one face, denoting the architect, engineer, contractor, financier, developer and/or future site occupant or tenant when placed on the site of new construction and/or building or site renovation. ii. Temporary Replacement Signage: Existing uses which have removed permanent signage during a construction project may install temporary banners and/or rigid portable signs in lieu of permanent signage. Only one barrier or rigid portable sign shall be allowed per street frontage. Wall-hung and wall-pole strung banners shall not exceed 100 square feet in size, pole- hung banners shall not exceed 20 square feet in size and rigid portable signs shall not exceed 32 square feet in size. The above temporary signage may only be displayed in conjunction with a 1 ORDINANCE NO. 4843 valid building or construction permit. Temporary replacement signs shall be removed at, or prior to, the finalization of the buildhig permit. SECTION II. Sections 4-4-100.H.4, 5a, 5b, 5c and 5h of Chapter 4, Property Development Standards, of Title 4 (Development Regulations), of Ordinance No. 4260 entitled "Code of General Ordinances General Ordinances of the City of Renton, Washington" are hereby amended as shown on Attachment A which is hereby incorporated. SECTION III. Section 4-4-100.H.6.b.ii of Chapter 4, Property Development Standards, of Title 4 (Development Regulations), of Ordinance No. 4260 entitled "Code of General Ordinances General Ordinances of the City of Renton, Washington" is hereby amended to read as follows: ii. Properties with frontage on Rainier Avenue S.; or. SECTION IV. Section 4-4-100.H.6.b of Chapter 4, Property Development Standards, of Title 4 (Development Regulations), of Ordinance No. 4260 entitled "Code of General Ordinances General Ordinances of the City of Renton, Washington" is hereby amended by adding subsection iii which reads as follows: iii. Buildings exceeding 40 feet in height. SECTION V. This ordinance will be effective upon its passage, approval and 30 days after pubhcation. PASSED BY THE CITY COUNCIL this 22nd day of May , 2000. Brenda Arline, Deputy City Clerk 2 ORDINANCE NO. 4843 APPROVED BY THE MAYOR this 22nd day of May , 2000. Lawrence J. Warren, City Attorney Date of Publication: 5/26/2000 (Summary) ORD.849:05/09/2000:as. 3 Attachment A Page 1 4. Type and number of permanent signs allowed: a. Residential/Churches/Schools: Residential occupancies, churches, and schools in the City Center are subject to the requirements of subsection E4 of this Section, signs Permitted in All Residential, Commercial, and Industrial Zones. b. Non-Residential Uses: Non-residential occupancies (excluding churches and schools) are subject to the following standards based upon sign category: SIGN CATEGORY TYPE AND NUMBER OF SIGNS ALLOWED CATEGORY A Freestanding OR Ground OR Wall Select only one of the following sign types: Number One free-standing sign per street frontage for each single occupancy building located on a corner lot, multi- occupancy building, or multiple building complex. The maximum number of signs is 2. One ground sign per street frontage for each single occupancy building, multi- occupancy building, or multiple building complex. The maximum number of signs is 2. Each individual ground-level business may have one wall sign for each business facade fronting on a public street. In addition, in multiple building complexes, or for multi-occupancy buildings each ground-level tenant with an exterior business facade may have one wall sign to identify individual tenant spaces. Mix of options for lots with multiple frontages An applicant for a business having more than one street frontage may substitute an allowed Category A sign type for another Category A sign type; however, the maximum number of signs shall not be exceeded. For example, on a corner lot, an applicant may request one ground sign facing one street frontage, and one freestanding sign facing the other street frontage. Attachment A Page 2 SIGN CATEGORY Multi-occupancy buildings or multiple building complexes - greater than 50,000 square feet with frontage on Rainier Ave. S. TYPE AND NUMBER OF SIGNS ALLOWED Multi-occupancy buildings or multiple building complexes with 50,000 square feet of gross leasable floor area or greater, and with frontage on Rainier Avenue S., may choose to comply with the above Category A regulations, or comply with the freestanding, ground, and wall sign size allowances of subsections E5a(ii), Wall Signs Business Signs-General, and E5d, Freestanding Signs in Shopping Centers Less Than Ten (10) Acres, either: (1) The above Category A regulations; or (2) Freestanding or ground signs and wall signs per the following standards: (i) Freestanding or Ground Signs: Have only one sign for each street frontage of any one of the following types: Freestanding, ground, or combination. Each freestanding or ground sign shall not exceed an area greater than one and one-half (1 1/2) square feet for each lineal foot of property frontage which the business occupies up to a maximum of three hundred (300) square feet; or if such sign is multi- faced, the maximum allowance shall not be more than three hundred (300) sguare feet. However, a maximum of one-half (1/2) of the allowed square footage is allowed on each face. Businesses with less than twenty five (25) lineal front feet may have a sign of a maximum of twenty (20) square feet per face. In addition, one (1) freestanding sign is allowed for each street frontage of the complex. Each sign shall not exceed an area greater than one and one-half (1-1/2) square foot for each linear foot of property frontage, not to exceed one hundred fifty (150) square feet per sign face and a maximum of three hundred (300) square feet including all sign faces. (ii) Wall Signs: In addition to the above freestanding or ground signs, wall signs are permitted with a total copy area not exceeding twenty percent (20%) of the building facade to which it is applied. Roof signs are prohibited per subsection C11. Projecting signs are regulated per this subsection and subsection H5d. Buildings 40 feet or greater in height Buildings 40 feet or greater in height may choose to comply with either: (1) The above Category A regulations; or (2) Freestanding or ground signs and wall signs per the following standards. (i) Freestanding or Ground Signs: Have only one sign for each street frontage of any one of the following types: Freestanding, ground, or combination. Each freestanding or ground sign shall not exceed an area greater than three hundred (300) square feet; or if such sign is multi-faced, a maximum of one-half (1/2) of the allowed sguare footage is allowed on each face. (ii) Wall Signs: In addition to the above freestanding or ground signs, wall signs are permitted with a total copy area not exceeding twenty percent (20%) of the building facade to which it is applied. Roof signs are prohibited per subsection C11. Projecting signs are regulated per this subsection and subsection H5d. Attachment A Page 3 SIGN CATEGORY TYPE AND NUME \ER OF SIGNS ALLOWED CATEGORY B Select only one of the following sign types. Allowed in addition to signs of Category A. Projecting Sign OR Awning Sign, or Canopy Sign, or Marquee Sign, or Traditional Marquee Sign Number Each individual ground-level business may have one sign for each business facade fronting on a public street. In addition, in multiple building complexes, or for multi-occupancy buildings each ground-level tenant with an exterior business facade may have one sign to identify individual tenant spaces. Each individual ground-level business may have one sign for each business facade fronting on a public street In addition, in multiple building complexes, or for multi- occupancy buildings each ground-level tenant with an exterior business facade may have one sign to identify individual tenant spaces. A series of awnings or canopies upon a single business and located on a single street frontage are considered as one awning or canopy. SIGN CATEGORY TYPE AND NUMBER OF SIGNS ALLOWED CATEGORY C Allowed in addition to signs of Categories A and B: Under Awning/ Under Canopy/ Under Marquee AND Secondary Wall, Projecting, or Awning Sign, having no internal illumination AND If applicable, Multi-Occupancy Building Sign, or Multiple Building Complex Wall Sign Number One per ground-level business per public entrance. One sign, having no internal illumination, per business facade which does not contain a Category A or B sign; maximum of 2 secondary signs. (1) Buildings Less Than 40 Feet in Height: One per buildinq facade which does not contain any other Category A, or B sign. (2) Buildinqs 40 Feet in Heiqht or Greater: Mav be placed on a building facade, containing a Cateqorv A or B sign, if the sign is placed on the facade a minimum of 25 feet above grade, measured to the bottom of the sign. (Ord. 4720, 5-4-98) Attachment A Page 4 FREESTANDING SIGNS SIZE, HEIGHT AND LOCATIONS ALLOWED FOR PERMANENT SIGNS FOR NON-RESIDENTIAL USES BASED UPON SIGN TYPE: MAXIMUM SIGN AREA MAXIMUM HEIGHT LOCATION AND OTHER LIMITATIONS REQUIRED CLEARANCES (Refer also to RMC 4-4-100K16, K17, K18) O R D I N A N C E N O . 4 8 4 3 (1) General: Each sign shall not exceed an area greater than 1.5 square feet for each lineal foot of street frontage which the building or complex occupies up to a maximum of 25 square feet per face; the maximum cumulative square footage of all faces of a sign is 50 square feet. (2) Property with frontage on Rainier Avenue S: In lieu of the sign area requirements of subsection (1), each sign shall not exceed an area greater than 1.5 square feet for each lineal foot of street frontage which the building or complex occupies up to a maximum of 75 square feet per face; the maximum cumulative square footage of all faces of a sign is 150 square feet; provided, that the sign is located in accordance with subsection (6) of this chart. (3) Multi-occupancy buildings or multiple building complexes with greater than 50,000 square feet gross leasable floor area, having frontage on Rainier Avenue S: Such uses may comply with the standards of subsections (1) or (2) above, or with the sign area standards of subsection E5d of this Section, Freestanding signs in Shopping Centers Less Than Ten (10) Acres subsection H4b, Type and Number of Permanent Siqns Allowed. Freestanding sign area mav be transferred from within the City Center Sign Regulation Boundaries to contiguously owned property outside of the City Center Sign Regulation Boundaries. Only sign area may be transferred, not the number of allowed signs. Where transferred, the maximum size of the free-standing sign shall not exceed the limits of subsection E5d of this Section, Freestanding signs in Shopping Centers Less Than Ten (10) Acres H4b, Type and Number of Permanent Siqns Allowed. (4) 20 feet, measured to the top of the sign or sign structure, whichever is higher (5) Setbacks shall be consistent with the Zoning Code. (6) Property with street frontage on Rainier Avenue S: The sign shall be located along Rainier Avenue S. and setback a minimum distance of 100 lineal feet from the right-of- way of S. Third Street. This setback shall not apply to multi-occupancy buildings or multiple building complexes with 50,000 square feet gross leasable floor area or greater, having frontage on Rainier Avenue S. (7) Minimum 15 foot clearance above traffic aisles and driveways. O R D I N A N C E N O . 4 8 4 3 Attachment A Page 5 GROUND SIGNS SIZE, HEIGHT AND LOCATIONS ALLOWED FOR PERMANENT SIGNS FOR NON-RESIDENTIAL USES BASED UPON SIGN TYPE: MAXIMUM SIGN AREA MAXIMUM HEIGHT LOCATION AND OTHER LIMITATIONS REQUIRED CLEARANCES (Refer also to Section 4-4-100K16, K17, and K18) (1) General: Each sign shall not exceed an area greater than 1.5 square feet for each lineal foot of street frontage which the building or complex occupies up to a maximum of 25 square feet per face; the maximum cumulative square footage of all faces of a sign is 50 square feet. (2) Property with frontage on Rainier Avenue S: In lieu of the sign area requirements of subsection (1), each sign shall not exceed an area greater than 1.5 square feet for each lineal foot of street frontage which the building or complex occupies up to a maximum of 75 square feet per face; the maximum cumulative square footage of all faces of a sign is 150 square feet; provided, that the sign is located in accordance with subsection (6) of this chart. (3) Multi-occupancy buildings or multiple building complexes with greater than 50,000 square feet gross leasable floor area, having frontage on Rainier Avenue S: Such uses may comply with the sign area standards of subsections (1) or (2) above, or with the size standards of subsection E5d of this Section, Freestanding signs in Shopping Centers Less Than Ten (10) Acres H4b, Tvpe and Number of Permanent Siqns Allowed. Ground sign area may be transferred from within the City Center Sign Regulation Boundaries to contiguously owned property outside of the City Center Sign Regulation Boundaries. Only sign area may be transferred, not the number of allowed signs. Where transferred, the maximum size of the ground sign shall not exceed the limits of subsection E5d of this Section, Froestanding signs in Shopping Centers Less Than Ton (10) Acres H4b, Tvpe and Number of Permanent Siqns Allowed. (4) 5 feet if perpendicular to the right-of-way; 4 feet if the sign is not placed perpendicular to the right-of-way. Height is measured to the top of the sign or sign structure, whichever is higher. (5) Setbacks shall be consistent with the Zoning Code, and Section 4-4-100L1b.. (6) Property with street frontage on Rainier Avenue S: The ground sign shall be located along Rainier Avenue S. and setback a minimum distance of 100 lineal feet from the right-of-way of S. Third Street. This setback shall not apply to multi- occupancy buildings or multiple building complexes with 50,000 square feet gross leasable floor area or greater, having frontage on Rainier Avenue S. Attachment A Page 6 WALL SIGNS SIZE, HEIGHT AND LOCATIONS ALLOWED FOR PERMANENT SIGNS FOR NON-RESIDENTIAL USES BASED UPON SIGN TYPE: MAXIMUM SIGN AREA MAXIMUM HEIGHT LOCATION AND OTHER LIMITATIONS REQUIRED CLEARANCES (Refer also to RMC 4-4-100K16, K17and K18) (1) General: Each sign shall not exceed an area greater than 1.5 square feet for each lineal foot of business facade fronting a street, up to 100 square feet maximum. (2) Multi-occupancy buildings or multiple building complexes with 50,000 square feet gross leasable floor area or greater, having frontage on Rainier Avenue S: In lieu of subsection (1), the sign area standards of subsection E5a(ii) of this Section, Wall Signs H4b, Tvpe and Number of Permanent Siqns Allowed, may be met. (3) Buildinqs 40 feet or greater in height: In lieu of subsection (1), the siqn area standards of subsection H4b, Type and Number of Permanent Siqns Allowed, may be met. (3) (4} The wall sign shall be placed on the facade not more than 25 feet above the grade, measured to the top of the sign. Wall siqns on This shall not apply to multi-occupancy buildings or multiple building complexes with 50,000 square feet gross leasable floor area or greater, having frontage on Rainier Avenue S. or buildinqs 40 feet or qreater in height mav be placed anywhere on the facade and the top of the siqn shall not extend vertically above the fascia of the building. {4) (5} The sign shall be mounted on or above the business facade to which it is associated. (5) {6} The wall sign shall be placed on a business facade having street frontage; or, it shall be placed on or above the business entrance, if the business has an exterior facade which does not face a street, and the business is located in a multi-tenant building or multiple building complex. (§) £7) The thickness of that portion of a wall sign which projects over a public right-of-way shall not exceed 12 inches. (8) Wall siqns located more than above 25 feet above qrade, measured to the top of the siqn, shall only contain the name and/or loqo of the business(es) or development. (7-) £8} When projecting over a public right-of-way (maximum 12 inches), a minimum of 8 feet clearance above the surface of the sidewalk is required. Attachment A Page 7 sh. MULTI OCCUPANCY OR MULTIPLE BUILDING COMPLEX SIGN SIZE, HEIGHT AND LOCATIONS ALLOWED FOR PERMANENT SIGNS FOR NON-RESIDENTIAL USES BASED UPON SIGN TYPE: MAXIMUM SIGN AREA MAXIMUM HEIGHT LOCATION AND OTHER LIMITATIONS REQUIRED CLEARANCES (Refer also to RMC 4-4-100K16, K17, and K18) (1) Buildinqs Less Than 40 Feet in Heiqht: Siqn size is restricted by lettering height. The maximum square footage limitation is 100 square feet. (2) Buildinqs 40 Feet in Heiqht or Greater: The maximum square footaqe limitation is 100 square feet unless the choice is made to comply with subsection H4b, Type and Number of Siqns Allowed for Non-Residential Uses. (2) (3) Buildinqs Less Than 40 Feet in Heiqht: The wall sign shall be placed on the facade not more than 25 feet above the grade, measured to the top of the sign. (4) Buildinqs 40 Feet in Heiqht or Greater: The wall siqn may be placed anywhere on the facade. (34(5) Buildinqs Less Than 40 Feet in Heiqht: The siqn shall be located on a business facade which does not contain any other Category A, or B sign. (6) Buildinqs 40 Feet in Heiqht or Greater: There are no restrictions on facade placement. (4) £7} The sign shall only contain the business name and/or logo of each development. (§) £8} When projecting over a public right-of-way, a minimum of 8 feet clearance above the grade is required (Ord. 4720, 5-4-98) REJ/ Central/sys2/depts/economicdevelopment/stratpln/planning/jenkins/signs/downtown sign revisions3-legal2.doc