HomeMy WebLinkAbout1545 - Avana Ridge - BP - 2012 Energy Code WorksheetInstructions for Electronic Forms, pg 1
Revised Jan 2014
Commercial Provision Chapters 1 - 5 of the 2012 Washington State Energy Code apply to all commercial occupancies, R-2
and R-3 occupancies greater than 3 stories above grade, and R-1 occupancy (all building heights).
Intro This file, LTG12-v3.XLSM, has electronic compliance forms for electrical power and lighting system provisions as defined
Section C405. This includes interior and exterior lighting systems, electric motors, and transformers. There are two companion
files: ENV12-v3.XLSM (Sections C101, C303, C402 and Appendix A envelope requirements) and MECH12-v3.XLSM (Section
C403 mechanical systems requirements).
This form is a compliance aid and is not a substitute for the full energy code text or specific jurisdiction compliance
requirements. Users should refer to the code text and contact the local jurisdiction for complete information. The full 2012
WSEC code text is available for download from the NEEC website:
http:/www.neec.net/energy-codes
Training Refer to the NEEC website for instruction on how to complete all of the 2012 WSEC Compliance Forms.
Start-up Select this file from the NEEC website to download to your computer. When opening the file be sure to Enable Macros.
This file is an Excel workbook that contains multiple compliance forms and resources in Excel worksheets. Each worksheet
is indicated by a tab at the bottom of the screen. You may visit each worksheet by selecting it's tab.
Most calculations are automated. Cells that display informational text and the results of calculations are write-protected and
cannot be edited.
Save Files This file is saved in the same manner as any standard Excel file.
Getting
Around
Some forms have two pages. Both pages are available on screen when you select the tab for a form (worksheet). Use the
scroll bars to find the second page located below the first page.
All general project information and the date are entered once on LTG-SUM. This information is automatically replicated on
all other LTG forms. The LTG-SUM form accompanies all other LTG forms except LTG-EXT, which is a stand alone form.
Only input cells are accessible. If you try to edit a write-protected cell an error message will appear requesting a password.
A password IS NOT required to complete these forms. You may use the TAB key to move to the next input cell. If the TAB
doesn't take you where you want to go, use your mouse to move around the form.
Avoid excessively long text strings when entering information. In some cases, text that extends beyond the available space
will not be visible. In most cases the text will wrap within the cell. This may force part of the form onto a new page.
To enter the date, use this format: mm/dd/yyyy. For example, you would enter 7/1/2013 or 12/21/2014.
Check boxes can be checked or unchecked by clicking in the box with your mouse. Radio buttons (circles) allow only one in
a set to be selected.
Drop-down lists have an arrow at the right side of the cell. Click on the arrow with your mouse and select the appropriate
option. Use the delete button on your computer to clear a drop-down ent
When a form has a space for notes or explanation, click anywhere in the space to edit.
Personalizing You can personalize the forms with your company name, address, phone, or any other information. This is done by editing
the header or footer in Excel.
Many tables, such as for listing proposed lighting fixture types, have a certain number of lines available for entering data.
You may need more lines to enter all your information. Where this feature is available, you can add additional lines to the table
by selecting the "+" button on the right hand side of the table with your mouse.
To remove lines that you have added, select the "-" button with your mouse. This will delete the last line of the section. You
cannot remove lines that were not added; an error message will appear if you try.
If you add additional lines with this method, the pagination may be affected forcing the forms to carry additional lines over to
other pages. Be sure to submit all pages to the plans examiner.
Compliance
Path You must select a Compliance Path on LTG-SUM (line 12).
Interior LTG
Power
Allowance
Method
You must select a Lighting Power Allowance Method on LTG-SUM (line 14) to activate the required worksheets and
automatically calculate interior lighting power allowances.
Exterior LTG
Zone
You must select a Lighting Zone on LTG-EXT (line 12) to activate this worksheet to display the applicable base site
allowance and automatically calculate the applicable exterior lighting power allowances.
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1
Energy Code
Overview
Input Cells
Adding And
Deleting
Lines
Instructions for Electronic Forms, pg 2
Revised Jan 2014
For projects complying via the Building Area Method, provide the total gross interior area for each Building Area Type in the
Maximum Allowed Lighting Wattage table using the drop down menu.
Assign a Building Area using the drop menu for each lighting fixture type defined in the Proposed Lighting Wattage table.
The worksheet will total all fixtures assigned to each Building Area.
Each Buidling Area shall comply independently.
For projects complying via the Space-By-Space Method, provide total gross interior area for each Space Type in the
Maximum Allowed Lighting Wattage table using the drop down menu.
For Atriums, provide total gross interior area and ceiling height (above finished floor) in the Maximum Allowed Lighting
Wattage table.
All Retail Display lighting shall be entered in the LTG-INT-DISPLAY worksheet. Results from this worksheet automatically
transfer to the LTG-INT-SPACE worksheet in the assigned locations under Maximum Allowed Lighting Wattage and Proposed
Lighting Wattage tables.
For projects with Retail Display lighting that is in addition to Retail Sales general area lighting, assign a Retail Display
category (per Table C405.5.2(2) Footnote A) to each lighting fixture type defined in the Proposed Display Lighting Wattage
table using the drop down menu.
Provide the total gross interior area for each eligible Retail Display category in the Maximum Allowed Display Lighting
Wattage table using the drop down menu.
The total Retail Display gross interior area entered in the LTG-INT-DISPLAY worksheet may not exceed the total Retail
Sales gross interior area entered in the LTG-INT-SPACE worksheet.
Provide square-foot surface area, perimeter linear feet, or number of items for each Surface Type in the Tradable and Non-
Tradable Maximum Allowed Lighting Wattage tables using the drop down menus.
Assign a Surface using the drop menu for each exterior lighting fixture type defined in the Tradable and Non-Tradable
Proposed Lighting Wattage tables.
The forms should print on any printer supported by your operating system. You will need to have the following TrueType
fonts installed under Windows: Arial, Times New Roman, Courier New and Wingdings. These are all standard Windows
fonts.
If you are losing form details when printing, you may have a shortage of printer memory. Try printing problem pages
individually.
By default, only the active worksheet is printed. To print more than one worksheet at a time, open your print set-up menu
and select either the page range you wish to print or Entire Workbook.
Forms (worksheets) in a workbook may not be deleted because the file is locked.
To print blank forms to fill out by hand, delete all of the heading information at the beginning of LTG-SUM and select the
desired Lighting Power Allowance Method.
For each radio button group there is a button labeled "Clear." Clicking this button will clear the other buttons so that they will
print as empty circles. The "Clear" button will not print.
End of Instructions for Electronic Forms
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1
Exterior LTG
Printing
Blank Forms
Interior LTG
Retail
Display
Interior LTG
Space-By-
Space
Method
Interior LTG
Building
Area Method
Interior Lighting Summary LTG-SUM
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Info Project Address 10616 SE 172nd Street, Renton, WA 98055 Date 12/29/2015
For Building Department Use
Applicant Name:Avana Ridge, LLC
Applicant Address:9675 SE 36th Street, Suite 105
Applicant Phone:Office: 206-588-1147
Project Description FALSE
Interior Lighting System
Description
Briefly describe lighting
system type and features.
Additions and Change of Space Use (C101.4.3 & C101.4.4)
Alterations, Renovations and Repairs (C101.4.3.1)
Provide Building Area Method (LTG-INT-BLD) or Space-By-Space Method (LTG-INT-SPACE) Compliance Form. Document
maximum allowed and proposed (including existing if applicable) lighting wattage of Addition or Change of Use space. Provide
applicable lighting controls per C405.2 and commissioning of lighting controls per C405.13.
Provide Building Area Method (LTG-INT-BLD) or Space-By-Space Method (LTG-INT-SPACE) Compliance Form. Document
maximum allowed wattage within the lighting retrofit space in Maximum Allowed Wattage table and proposed (including existing)
lighting wattage in Proposed Wattage table. Retrofit and non-retrofit spaces shall be documented separately using multiple forms.
Provide all applicable lighting controls as noted for New Wiring and commissioning of lighting controls per C405.13.
Provide a separate Space-By-Space Method (LTG-INT-SPACE) Compliance Form for this retrofit area. Document existing total
wattage within the lighting retrofit space in cell provided in the Maximum Allowed Wattage table. Document proposed (including
existing) lighting wattage in the Proposed Wattage table.
Lighting Compliance Path
Lighting Power Allowance
Method
Provide all applicable lighting controls as noted for New Wiring, automatic time switch controls (C405.2.2.1), and commissioning of
lighting controls per C405.13.
Provide applicable manual lighting controls (C405.2.1), occupancy sensors (C405.2.2.2), daylight zone controls (C405.2.2.3), specific
application controls (C405.2.3), and commissioning of lighting controls per C405.13
New Building Addition Alteration
Building Area Method Space-By-Space Method
Addition area or Change of Space Use area complies with all applicable provisions as stand alone project
Addition area is combined with existing building lighting systems to demonstrate compliance with all applicable
provisions per C101.4.3
(If Total Building Performance then only LGT-CHK is
Total Building PerformanceLighting Power Density Calculations
new multifamily building - lighting at dwelling units and common areas
60% or more of luminaires in space replaced
Less than 60% of luminaires in space replaced
Lamp and/or ballast replacement within existing luminaires only – existing total interior building wattage not increased
New wiring installed to serve added fixtures and/or fixtures relocated to new circuit
New or moved lighting panel
Space is reconfigured - luminaires unchanged or moved only
No changes are being made to the interior lighting and space use not changed.
Compliance forms do not require a password to use. Instructional and calculating cells are write-
Selection required to
enable LPA forms
Plans Included
Interior Lighting Summary - Space-By-Space LTG-INT-SPACE
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Address 10616 SE 172nd Street, Renton, WA 98055 Date 12/29/2015
Lighting Alterations, Renovations & Building Additions For Building Department Use
Total Building Performance - No lighting calcs required
Location (plan #,
room #) Space Type*
Allowed
Watts per ft2
Gross Interior
Area in ft2
Watts Allowed
(watts/ft2 x area)
Retail Display Allowance from LTG-INT-DISPLAY
Area Allowed Watts
Total
Total Building Performance - No lighting calcs required
Location (plan #,
room #) Fixture Description***
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
Retail Display Lighting from LTG-INT-DISPLAY
Total Proposed Watts
Interior Lighting Power Allowance
*** Include existing to remain lighting fixtures and exempt lighting equipment per notes below.
Notes:
1. Include ALL proposed lighting fixtures.
2. For proposed Fixture Description, indicate fixture type, lamp type (e.g. T-8), number of lamps in the fixture, and ballast type (if included).
For
track lighting, list the length of the track (in feet) in addition to the fixture, lamp, and ballast information.
3. For proposed Watts/Fixture, use manufacturer's listed maximum input wattage of the fixture (not simply the lamp wattage) and other
criteria
as specified in Section C405.5.1. For line voltage track lighting, list the greater of actual luminaire wattage or length of track multiplied by
50,
or as applicable, the wattage of current limiting devices of the transformer. For low voltage track lighting list the transformer rated wattage.
4. For lighting equipment eligible for exemption per C405.5.1, note exception number and leave Watts/Fixture blank.
5. Document existing to remain fixtures in Proposed Lighting table in the same manner as new fixtures. Identify as existing in fixture
description.
* Select Table C405.5.2(2) category from drop down menu.
** For atriums, indicate height. Allowed wattage for first 40 feet is 0.03 W/ft. ht.,
above 40 feet is 0.02 W/ft. ht.
Total Proposed Watts may not exceed Total Allowed Watts for Interior Lighting
Atrium** Enter
Height:Existing Lighting Enter Exist.
Watts:
Addition
combined
Stand alone
bldg. addition
60% or more
fixtures
Less than 60%
fixtures replaced
Notes:
a. Lighting fixtures in a building addition may comply as a stand alone project, or they may be
combined with the overall existing bldg lighting to demonstrate compliance. Refer to
C101.4.3.
b. For retrofits and building additions, provide Space Types and gross interior areas in the
Maximum Allowed Lighting table. If a builidng addition will comply as combined with the
overall
existing builidng, include all applicable existing Space Types and gross interior areas.
c. Document new fixtures and all existing to remain fixtures in the Proposed Lighting table.
d. If less than 60% of existing fixtures will be replaced, provide total existing lighting wattage
(prior to retrofit) in the space provided in the Maximum Allowed Lighting table.
Interior Display Lighting - Space-by-Space LTG-INT-DISPLAY
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Info Project Address 10616 SE 172nd Street, Renton, WA 98055 Date 12/29/2015
For Building Department Use
Applicant Name:Avana Ridge, LLC
Total Building Performance - No lighting calcs required
Location (plan #
room #)
Allowed
Watts per ft2 **
Gross Interior
Area in ft2
Watts Allowed
(watts/ft2 x area)
Area Area Watts
Total
Display Lighting Base Allowance
++ Total Display Allowance
Total Building Performance - No lighting calcs required
Display Area*
Location (plan #
room #) Fixture Description
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
Total Proposed Watts
Retail 1 Retail 2 Retail 3 Retail 4
Retail Display Area Type*
Only separately controlled display fixtures independent of general area lighting per Table C405.5.2(2) footnote A may be entered here.
Notes:
1. For proposed Display Fixture Description, indicate fixture type, lamp type (e.g. T-8), number of lamps in the fixture, and ballast type (if
included). For track lighting, list the length of the track (in feet) in addition to the fixture, lamp, and ballast information.
2. For proposed Watts/Fixture, use manufacturer's listed maximum input wattage of the fixture (not simply the lamp wattage) and other
criteria as specified in Section C405.5.1. For line voltage track lighting, list the greater of actual luminaire wattage or length of track
multiplied by 50, or as applicable, the wattage of current limiting devices or of the transformer. For low voltage track lighting list the
transformer rated wattage.
3. List all display fixtures.
* Only retail sales areas that meet the requirements defined in Table
C405.5.2(2) footnote A may be entered here. Select retail sales areas form drop
down menu.
** Wattages per Table C405.5.2(2) footnote A.
++ Display light allowance per footnote A calculation.
* Select retail sales display area from drop down menu.
Proposed Display
Lighting Totals
Interior Lighting Summary - Building Area Method LTG-INT-BLD
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Address 10616 SE 172nd Street, Renton, WA 98055 Date 12/29/2015
For Building Department Use
Total Building Performance - No lighting calcs required
Building Area*
Location (plan #,
room #, or ALL)Area Description
Allowed
Watts per ft2
Gross Interior
Area in ft2
Watts Allowed
(watts/ft2 x area)
Total
Total Building Performance - No lighting calcs required
Building Area*
Location (plan #,
room #) Fixture Description**
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
Compliance by Building Area
Building Area
Total Allowed
Watts
Total Proposed
Watts
Interior Lighting Power
Allowance
Total
Lighting Alterations, Renovations & Building Additions
Warnings
* Select Table C405.5.2(1) Building Area from drop down menu.
* Select Table C405.5.2(1) Building Area from drop down menu.
** Include existing to remain lightingand exempt lighting equipment per notes below.
Addition
combined
Stand alone
bldg. addition
60% or more
fixtures
Less than 60%
fixtures replaced
Notes:
a. Lighting fixtures in a building addition may comply as a stand alone project, or they may be
combined with the overall existing bldg lighting to demonstrate compliance. Refer to C101.4.3.
b. For retrofits and building additions, provide Building Area types and gross interior areas in the
Maximum Allowed Lighting table. If a builidng addition will comply as combined with the overall
existing builidng, include all applicable existing Building Area types and gross interior areas.
c. Document new fixtures and all existing to remain fixtures in the Proposed Lighting table.
d. If less than 60% of existing fixtures will be replaced, use LTG-INT-SPACE form.
Notes:
1. Proposed Wattage for each Building Area type shall not exceed the Allowed Wattage for that Building Area type. Trading wattage
between
Building Area types is not allowed under the Building Area Method compliance path.
2. Proposed fixtures must be listed in the building area in which they occur. Include ALL proposed lighting fixtures.
3. For proposed Fixture Description, indicate fixture type, lamp type (e.g. T-8), number of lamps in the fixture, and ballast type (if included).
For
track lighting, list the length of the track (in feet) in addition to the fixture, lamp, and ballast information.
4. For proposed Watts/Fixture, use manufacturer's listed maximum input wattage of the fixture (not simply the lamp wattage) and other
criteria
as specified in Section C405.5.1. For line voltage track lighting, list the greater of actual luminaire wattage or length of track multiplied by
50,
Exterior Lighting Summary LTG-EXT
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Info 10616 SE 172nd Street, Renton, WA 98055 Date 12/29/2015
For Building Department Use
Avana Ridge, LLC
9675 SE 36th Street, Suite 105
Office: 206-588-1147
Project Description
Lighting Zone
Compliance Option
Building Grounds
Applies to luminaires > 100 Watts
Tradable Maximum Allowed Lighting Wattage Base Site Allowance:500
Tradable Surfaces Surface Description
Allowed Watts
per ft2 or per lf
Area (ft2), perimeter
(lf) or # of items
Allowed Watts
x ft2 (or x lf)
Total Allowed Tradable Watts:
Tradable Proposed Lighting Wattage (Use mfgr listed maximum input wattage for luminaire.)
Tradable Surface Fixture Description
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
Total Proposed Tradable Watts:
Non-Tradable Maximum Allowed Lighting Wattage Base Site Allowance Remaining: 500
Non-Tradable Surfaces Surface Description
Allowed Watts
per ft2 or per lf
Area (ft2), perimeter
(lf) or # of items
Allowed Watts
x ft2 (or x lf)
Non-Tradable Proposed Lighting Wattage
Non-Tradable Surface Fixture Description
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
Total excess Non-Tradable watts:0
Site Allowance Balance:500
Exterior Lighting
Exterior Lighting Alterations
New Building Addition Alteration
Zone 4
Efficacy > 60 lumens/W
Exemption (list)
No changes are being made to the existing exterior lighting
Controlled by motion sensor
Lighting Power Density Calculations Total Building Performance
Zone 3Zone 2Zone 1
Non-tradable proposed watts may not exceed allowed watts for any individual
surface unless the total excess watts for all non-tradable surfaces are less than
the remaining site allowance.
Total proposed tradable watts may not exceed the sum of total allowed tradable
watts plus the base site allowance. Any base site allowance not needed to
make tradable watts comply can be applied to individual non-tradable
New wiring installed to serve added fixtures and/or fixtures relocated to new circuit
Plans Included
Provide applicable exterior lighting controls per C405.2.4 and commissioning per
As specified by jurisdiction. Zone
selection required to enable LTG-EXT
form
Project Address:
Applicant Name:
Applicant Addr:
Applicant Phone:
Lighting, Motor, and Transformer Permit Documents Checklist LTG-CHK
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Address 10616 SE 172nd Street, Renton, WA 98055 Date 12/29/2015
Applicability
(yes,no,na) Code Section Component Compliance information required in permit documents
Location in
Documents
Building Department
Notes
LIGHTING CONTROLS (Section C405.2)
Indicate on plans the manual control type & locations served;DEFERRED
Indicate of plans the 50% lighting load reduction method
provided or identify exception taken DEFERRED
Indicate lighting system automatic shut-off capability - identify
lighting zone areas served on plans;DEFERRED
Indicate locations of override switches on plans and the areas
served, include area sq. ft.;DEFERRED
Indicate locations where automatic shutoff is provided by other
methods (occupancy sensor, daylight controls, etc)DEFERRED
C405.2.2.2 Occupancy sensors Indicate on plans the locations served by occupancy sensors DEFERRED
Indicate vertical fenestration primary and secondary daylight
zone areas on plans, include sq. ft.;DEFERRED
Indicate skylight daylight zone areas on plans, include sq. ft.DEFERRED
Indicate on plans the locations served by daylight zone controls;DEFERRED
Indicate in plans the lighting load reduction (dimming) method -
stepped or continuous dimming DEFERRED
Yes C405.2.3
Specific application
lighting controls -
General
Indicate on plans the locations served by specific application
lighting controls DEFERRED
Indicate lighting control method for display and accent lighting,
and display case lighting;
Indicate these fixtures are controlled independently from both
general area lighting and other lighting applications within the
same space
Provide a lighting control device at each guest room entry for all
permanently installed fixtures in guest room;
Indicated whether lighting control is manual or automatic
No C405.2.3 -
Item 4
Supplemental task
lighting
Provide automatic shut-off vacancy controls for supplemental
task lighting, including under-shelf or under-cabinet lighting
Identify eligible non-visual applications and method of lighting
control;
Indicate these fixtures are controlled independently from both
general area lighting and other lighting applications within the
same space
Indicate lighting control method for lighting equipment for sale
or demonstration;
Indicate these fixtures are controlled independently from both
general area lighting and other lighting applications within the
same space
If egress lighting power density is greater than 0.05W/ft2,
indicate method of automatic shut-off during unoccupied
periods;
DEFERRED
Identify on plans the egress fixtures that function as both normal
and emergency means of egress illumination DEFERRED
No C405.10
C405.11
Cooler and freezer
lighting
Provide vacancy device or timer to turn off fixtures within 15
minutes of unoccupancy for cooler and freezer lighting fixtures
with lamp efficacy less than 40 lumens per watt
DEFERRED
Yes C405.2.4 Exterior lighting
controls
Indicate on exterior lighting plans the automatic lighting control
method and locations served DEFERRED
Yes C405.6.1
Exterior building
grounds lighting
controls
Provide motion sensor controls for building grounds fixtures
rated at greater than 100 watts with lamp efficacy less than 60
lumens, or identify exception taken
DEFERRED
Identify applicable commissioning documentation requirements
per Section C408 or eligibility for exception;DEFERRED
Provide written procedures for functional testing of all automatic
controls and describe the expected system response;DEFERRED
Identify in construction documents the party responsible for
functional testing of automatic lighting controls DEFERRED
INTERIOR LIGHTING POWER & EFFICACY (Sections C405.5, C405.10, C405.11)
Provide fixture schedule with fixture types, lamps, ballasts, and
rated watts per fixture;DEFERRED
No C405.2.3 -
Item 6
Lighting equipment
for sale or
demonstration
Yes C405.2.3 -
Item 7
Means of egress
lighting
C40551
Yes C408.3 Lighting system
functional testing
No C405.2.3 -
Item 3
Hotel/motel guest
rooms
No C405.2.3 -
Item 5
Lighting for non-
visual applications
Yes C405.2.1.1
C405.2.1.2
Manual interior
lighting controls
Yes C405.2.2.1
Automatic time
switch controls and
override switching
Yes C405.2.2.3
Daylight zones -
Vertical fenestration
and skylights
Yes C405.2.2.3.2 Daylight zone
controls
No C405.2.3 -
Items 1&2
Display and accent
lighting
The following information is necessary to check a permit application for compliance with the lighting, motor, and transformer requirements in the
Washington State Energy Code, Commercial Provisions.
Lighting, Motor, and Transformer Permit Documents Checklist LTG-CHK
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Address 10616 SE 172nd Street, Renton, WA 98055 Date 12/29/2015
Applicability
(yes,no,na) Code Section Component Compliance information required in permit documents
Location in
Documents
Building Department
Notes
The following information is necessary to check a permit application for compliance with the lighting, motor, and transformer requirements in the
Washington State Energy Code, Commercial Provisions.
Identify spaces eligible for lighting power exemption on plans
and in compliance forms;DEFERRED
Identify lighting equipment eligible for exemption in fixture
schedule and in compliance forms;DEFERRED
Indicate that exempt lighting equipment is in addition to general
area lighting and is controlled independently DEFERRED
Yes C405.4 Exit signs
Provide exit sign types and rated watts per fixture in fixture
schedule (maximum 5 watts per fixture)DEFERRED
No C405.10
C405.11
Cooler and freezer
lighting
For lighting in walk-in coolers and freezers, and refrigerated
warehouse coolers and freezers, provide rated lamp efficacy (in
lumens per watt) in fixture schedule
DEFERRED
Lighting Power Calculation - Indicate compliance path taken
Yes C405.5.2 Building Area
Method
Complete required compliance forms – proposed wattage per
building area does not exceed maximum allowed wattage per
building area. Identify locations of building areas on plans
DEFERRED
No C405.5.2 Space-By-Space
Method
Complete required compliance forms – total proposed wattage
does not exceed maximum allowed wattage. Identify locations of
space types on plans, including retail display areas as
applicable
EXTERIOR LIGHTING POWER & EFFICACY (Section C405.6)
Provide fixture schedule with fixture types, lamps, ballasts, and
rated watts per fixture;DEFERRED
Identify exterior applications eligible for lighting power
exemption on plans and in compliance forms;DEFERRED
Indicate that exempt exterior lighting is controlled independently
from non-exempt exterior lighting DEFERRED
Yes Table
C405.6.2(1)Exterior lighting zone Indicate building exterior lighting zone as defined by the AHJ DEFERRED
Yes C405.6.1 Exterior building
grounds lighting
For building grounds fixtures rated at greater than 100 watts,
provide rated lamp efficacy (in lumens per watt) in fixture
schedule
DEFERRED
Yes C405.6.2 Exterior lighting
power calculations
Complete required compliance form – proposed wattage for
exterior lighting plus base site allowed does not exceed
maximum allowed
DEFERRED
MOTORS & TRANSFORMERS (Sections C405.8, C405.9)
Yes C405.8 Electric Motors
For motors not part of an HVAC system, provide electric motor
schedule on electrical plans with hp, rpm, and rated efficiency DEFERRED
Yes C405.9 Transformers
Provide distribution transformer schedule on electrical plans
with transformer size and efficiency DEFERRED
If "no" is selected for any question, provide explanation:
Yes No N.A.
Yes C405.6.2
Total connected
exterior lighting
power
Yes
C405.5.1
C405.5.1.1
C405.5.1.2
C405.5.1.3
C405.5.1.4
Total connected
interior lighting power