Loading...
HomeMy WebLinkAbout1_PRE21-000359_City Pre-application comment_ShumShortPlat_211210_v1PREAPPLICATION MEETING FOR Shum Short Plat 3607 NE 12th St PRE21-000359 CITY OF RENTON Department of Community & Economic Development Planning Division October 21, 2021 Contact Information: Planner: Angelea Weihs, 425.430.7312, aweihs@rentonwa.gov Public Works Plan Reviewers: Nathan Janders, 425.430.7382, njanders@rentonwa.gov Fire Prevention Reviewer: Corey Thomas, 425.276.9582, cthomas@rentonrfa.org Building Department Reviewer: Rob Shuey, 425.430.7235, rshuey@rentonwa.gov Please retain this packet throughout the course of your project as a reference. Consider giving copies of it to any engineers, architects, and contractors who work on the project. You will need to submit a copy of this packet when you apply for land use and/or environmental permits. Pre-screening: When you have the project application ready for submittal, call and schedule an appointment with the assigned planner to have the documents pre- screened. The pre-application meeting is informal and non-binding. The comments provided on the proposal are based on the codes and policies in effect at the time of review. The applicant is cautioned that the development regulations are regularly amended and the proposal will be formally reviewed under the regulations in effect at the time of project submittal. The information contained in this summary is subject to modification and/or concurrence by official decision-makers (e.g., Hearing Examiner, Planning Director, Community & Economic Development Administrator, Public Works Administrator, and City Council). M E M O R A N D U M DATE:October 18, 2021 TO:Angelea Weihs, Associate Planner FROM:Corey Thomas, Lead Plans Review Inspector SUBJECT:Shum Short Plat 1. The fire flow requirements for a single-family home is 1,000 gpm minimum for dwellings up to 3,600 square feet (including garage and basements). If the dwelling exceeds 3,600 square feet, a minimum of 1,500 gpm fire flow would be required. A minimum of one fire hydrant is required within 300-feet of the proposed buildings and two hydrants if the fire flow goes up to 1,500 gpm. Water main on Queen Avenue Northeast is dead end and will not support fire flows over 1,000 gpm. 2. The fire impact fees are currently applicable at the rate of $829.77 per single family unit. This fee is paid at building permit issuance. 3. Fire department apparatus access roadways are required to be a minimum of 20-feet wide fully paved, with 25-feet inside and 45-feet outside turning radius. Fire access roadways shall be constructed to support a 30-ton vehicle with 75-psi point loading. Access is required within 150-feet of all points on the buildings. Dead end streets that exceed 150-feet in length require an approved hammerhead turnaround, if access is proposed from Queen Avenue Northeast. AND ECONOMIC DEVELOPMENT M E M O R A N D U M DATE:October 18, 2021 TO:Angelea Weihs, Planner FROM:Nathan Janders, Plan Reviewer SUBJECT:Short Plat 3607 NE 12th St PRE19-000294 NOTE: The applicant is cautioned that information contained in this summary is preliminary and non- binding and may be subject to modification and/or concurrence by official City decision-makers. Review comments may also need to be revised based on site planning and other design changes required by City staff or made by the applicant. I have completed a preliminary review for the above-referenced proposal located at parcel(s) 1065700100. The following comments are based on the pre-application submittal made to the City of Renton by the applicant. Water 1. The project is within the City of Renton’s water service area in the Highlands 565 Pressure Zone. 2. The static water pressure is approximately 58 psi at ground elevation of 432 feet. 3. There is an existing 8-inch water main located in Pierce Ave NE that can deliver a maximum capacity of 2,400 GPM (see water plan No. W-363804). 4. There is an existing 8-inch dead end water main located in Queen Ave NE that can deliver a maximum capacity of 1,250 GPM (see water plan No. W-334301). 5. There is an existing 1-inch water service to the existing residence at 3607 NE 12 th St. 6. A separate water service (1-inch) and meter is required for each lot. The meters will be installed by City forces and a water meter permit is required for each meter and service line installation. The sizing of the meter and of the private service line to the buildings shall be in accordance with the most recent edition of the Uniform Plumbing Code Meters shall be placed in landscape strips, or behind the sidewalk, and within the right-of-way. Meters shall not be installed within driveways 7. A minimum 1-inch meter is required if the new homes are served by residential sprinkler systems. 8. Based on the review of project information submitted for the pre-application meeting, Renton Regional Fire Authority has determined that the preliminary fire flow demand for the proposed development is 1,000 gpm for homes under 3,600 SF and goes up to a minimum of 1,500 gpm for homes over 3,600 SF. 9. Installation of off-site and on-site fire hydrants, as required. The location and number of hydrants will be determined by the Fire Authority based on the final fire flow demand and final site plan. A minimum of 1 hydrant must be within 300 feet of each lot. 10. Civil plans for the water main improvements will be required and must be prepared by a professional engineer registered in the State of Washington. Please refer to City of Renton General Design and Construction Standards for Water Main Extensions as shown in Appendix J of the City’s 2012 Water System Plan. Adequate horizontal and vertical separations between the new water main and other utilities (storm sewer pipes and vaults, sanitary sewer, power, gas, electrical) shall be provided for the operation and maintenance of the water main. Retaining walls, rockeries or similar structures cannot be installed over the water main unless the water main is installed inside a steel casing. 11. A conceptual utility plan will be required as part of the land use application for the subject development. 12. The development is subject to applicable water system development charges (SDC’s) and meter installation fees based on the number and size of the meters for domestic uses and for fire sprinkler use. The development is also subject to fees for water connections, cut and caps, and purity tests. Current fees can be found in the 2021 Development Fees Document on the City’s website. Fees will be charged based on the rate at the time of construction permit issuance. The SDC fee for water is based on the size of the new domestic water to serve the project. The current water fee is $4,450.00 per 1-inch service. Water service installation charges for each proposed domestic water service is applicable. Water Service installation is $2,875.00 per 1-inch service line. Drop-in meter fee is $400 per ¾-inch meter and $460.00 per 1-inch meter. The full fee schedule can be found at: https://edocs.rentonwa.gov/Documents/DocView.aspx?id=8515298&dbid=1&repo=CityofR enton Sanitary Sewer 1. The project is within the City of Renton’s sanitary sewer service area. 2. There is an existing 8-inch gravity wastewater main located in Queen Ave NE (see record drawing S- 334304). 3. There is an existing 8-inch gravity wastewater main located in Pierce Ave NE (see record drawing S- 002901). 4. There is an existing 6-inch PVC sewer stub located in the northwest corner of the property. The stub may be re-used if in a suitable location for the project. 5. Any existing on site septic system on parcel 1065700100 shall be decommissioned in accordance with King County Department of Health and City of Renton standards. 6. Individual sewer stubs from the sewer main and individual side sewers are required for each lot. All new sewer stubs shall conform to the standards in RMC 4-6-040 and City of Renton Standard Details. 7. A conceptual utility plan will be required as part of the land use application for the subject development. 8. The development is subject to a wastewater system development charge (SDC) fee. SDC fee for sewer is based on the size of the new domestic water to serve the project. Current fees can be found in the 2021 Development Fees Document on the City’s website. Fees will be charged based on the rate at the time of construction permit issuance. The current sewer fee for is $3,450.00 per 1-inch meter Final determination of applicable fees will be made after the water meter size has been determined. The full fee schedule can be found at: https://edocs.rentonwa.gov/Documents/DocView.aspx?id=8515298&dbid=1&repo=CityofR enton Surface Water 1. There is an existing catchbasin at the southwest corner of the property connected to an 8-inch srotmwater main (see record drawing R-170701). 2. Drainage plans and a drainage report complying with the adopted 2017 Renton Surface Water Design Manual will be required. Refer to Figure 1.1.2.A – Flow Chart of the 2017 Renton Surface Water Design Manual (RSWDM) to determine what type of drainage review is required for this site. The site falls within the City’s Flow Control Standard – Matching Existing Peak. The site falls within the East Lake Washington drainage basin. 3. The current Surface Water Standard Plans shall be used in all drainage plan submittals. The current City of Renton Standard Details are available online in the City of Renton website https://edocs.rentonwa.gov/Documents/Browse.aspx?id=990403&dbid=0&repo=CityofRenton 4. If the new plus replaced pollution generating impervious surface exceeds 5,000 SF, the applicant will be required to provide basic water quality treatment. Any proposed detention and/or water quality vault shall be designed in accordance with the RSWDM that is current at the time of civil construction permit application. Separate structural plans will be required to be submitted for review and approval under a separate building permit for the detention and/or water quality vault. 5. Appropriate on-site BMPs satisfying Core Requirement #9 will be required to help mitigate the new runoff created by this development to the maximum extent feasible. On-site BMPs shall be evaluated in order of preference by feasibility as described in Section C.1.3 of the 2017 RSWDM. A preliminary drainage plan, including the application of on-site BMPs, shall be included with the land use application, as applicable to the project. The final drainage plan and drainage report must be submitted with the utility construction permit application. 6. A geotechnical soils report for the site is required per the 2017 Renton Surface Water Design Manual Section C.1.3. Information on the water table and soil permeability (measured infiltration rates), with recommendations of appropriate on-site BMPs per Core Requirement #9 and Appendix C shall be included in the report. The report should also include information concerning the soils, geology, drainage patterns and vegetation present shall be presented in order to evaluate the drainage, erosion control and slope stability for site development of the proposed plat. The applicant must demonstrate the development will not result in soil erosion and sedimentation, landslide, slippage, or excess surface water runoff. 7. Erosion control measures to meet the City requirements shall be provided. 8. The development falls within the R-8 zone which has a maximum impervious surface area of 65% per lot. 9. The development is subject to a surface water system development charge (SDC) fees. Fees will be charged based on the rate at the time of construction permit issuance. The current SCD fee for new single family homes is $2,000 per home. The full fee schedule can be found at: https://edocs.rentonwa.gov/Documents/DocView.aspx?id=8515298&dbid=1&repo=CityofR enton Transportation 1. Per City code 4-6-060 frontage improvements are required for new construction in excess of $150,000. The proposed project fronts NE 12th St to the north, Queen Ave NE to the east and Pierce Ave NE to the west. Queen Ave NE is classified as a residential access street with an existing right-of-way (ROW) width of approximately 50 ft (30 feet from centerline) per the King County Assessor Map. To meet the City’s complete street standards for Residential Access streets, a minimum ROW width of 53 ft is required. Per RMC 4-6-060 half of street improvements as taken from the ROW centerline shall be required and include a 26 foot paved road (13 feet each side), a 0.5 foot curb, an 8 foot planting strip, and a 5 foot sidewalk. No dedication will be required. Pierce Ave NE is classified as a residential access street with an existing right-of-way (ROW) width of approximately 30 feet except for the southern 20 feet which has an existing ROW width of approximately 50 ft according to the King County Assessor Map. To meet the City’s complete street standards for Residential Access streets, a minimum ROW width of 53 ft is required. Per RMC 4-6-060 half of street improvements as taken from the ROW centerline shall be required and include a 26 foot paved road (13 feet each side), a 0.5 foot curb, an 8 foot planting strip, and a 5 foot sidewalk. Pending a field survey, dedication of approximately 23 ft along the frontage of 1065700100 except the southern 20 feet for which a dedication of approximately 3 ft will be required. 2. Refer to City code 4-4-080 regarding driveway regulations. A minimum separation of 5 feet is required between driveway and the property line. Maximum driveway slopes shall not exceed 15%. Driveways exceeding 8% shall provide slotted drains. The maximum width of single loaded garage driveway shall not exceed nine feet (9') and double-loaded garage driveway shall not exceed sixteen feet (16'). 3. Access to lots may be restricted to Pierce Ave NE by plat development under King County recording numbers 8004230583 and 9802099012. 4. Undergrounding of all existing utilities is required on all frontages per RMC 4-6-090. 5. Street lighting is not required for a project that consists of less than 4 residential units. See RMC 4-6- 060 for street lighting requirements. 6. Paving and trench restoration within the City of Renton right of way shall comply with the City’s Trench Restoration and Street Overlay Requirements. 7. The development is subject to transportation impact fees. Fees will be charged based on the rate at the time of building permit issuance. The 2021 transportation impact fee is $10,861.69 per single family home. General Comments 1. If frontage improvements are required, all existing and proposed utility lines (i.e. electrical, phone, and cable services, etc.) along property frontage or within the site must be underground as outlined in RMC 4-6-090 – UTILITY LINES - UNDERGROUND INSTALLATION. The construction of these franchise utilities must be inspected and approved by a City of Renton inspector. 2. Maximum exposed retaining wall height is 6-ft and shall be setback a minimum of 3-ft from the right- of-way as outlined in RMC 4-4-040 – Fences, Hedges and Retaining Walls. 3. Adequate separation between utilities as well as other features shall be provided in accordance with code requirements. a. 7-ft minimum horizontal and 1-ft vertical separation between storm and other utilities is required with the exception of water lines which require 10-ft horizontal and 1.5-ft vertical. b. The stormwater line should be minimum 5 feet away from any other structure or wall or building. c. Trench of any utility should not be in the zone of influence of the retaining wall or of the building. 4. All construction utility permits for utility and street improvements will require separate plan submittals. All utility plans shall confirm to the Renton Drafting Standards. A licensed Civil Engineer shall prepare the civil plans. Please visit the Development Engineering Forms page for the most up- to-date plan submittal requirements: http://rentonwa.gov/business/default.aspx?id=42473 5. A landscaping plan shall be included with the civil plan submittal. Each plan shall be on separate sheets. 6. Fees quoted in this document reflect the fees applicable in the year 2019 only and will be assessed based on the fee that is current at the time of the permit application or issuance, as applicable to the permit type. Please visit www.rentonwa.gov for the current development fee schedule. CityofRenton\Department Folders\Community and Economic Development (CED)\Current Planning\Pre- Applications\2021\PRE21-000359\Working Files DEPARTMENT OF COMMUNITY AND ECONOMIC DEVELOPMENT M E M O R A N D U M DATE:October 21, 2021 TO:Pre-Application File No. 21-000359 FROM:Angelea Weihs, Associate Planner SUBJECT:Shum Short Plat – 1157 Queen Avenue NE (Parcel number 1065700100) General: We have completed a preliminary review of the pre-application for the above- referenced development proposal. The following comments on development and permitting issues are based on the pre-application submittals made to the City of Renton by the applicant and the codes in effect on the date of review. The applicant is cautioned that information contained in this summary may be subject to modification and/or concurrence by official decision-makers (e.g., Hearing Examiner, Community & Economic Development Administrator, Public Works Administrator, Planning Director, and City Council). Review comments may also need to be revised based on site planning and other design changes required by City staff or made by the applicant. The applicant is encouraged to review all applicable sections of the Renton Municipal Code. The Development Regulations are available online at https://www.codepublishing.com/WA/Renton/. Project Proposal: The subject property is a through-lot located at 1157 Queen Avenue NE (Parcel number 1065700100). The parcel has public street frontage on both Pierce Ave NE and Queen Ave NE and is located within the R-8 Zone. The site area is approximately 17,174 square feet (0.39 acres) and is currently vacant. The proposal is to subdivide the property into 2 lots. Access to the site appears to be proposed via residential driveways off of either Pierce Ave NE or Queen Ave NE. The proposed lot size for both Lots 1 and 2 is 7,474.99 square feet. No critical areas are mapped on the project site. Current Use: The property is currently vacant. Zoning/Density Requirements: The subject property is located within the Residential-8 (R-8) zoning classification. The density range allowed in the R-8 zone is a minimum of 4.0 to a maximum of 8.0 dwelling units per 1 net acre. The Residential Medium Density Land Use designation is intended to implement the R-8 zone. Development in the R-8 zone is intended to create opportunities for new single family residential neighborhoods and to facilitate high- quality infill development that promotes reinvestment in existing single-family neighborhoods. It is intended to accommodate uses that are compatible with and support a high-quality residential environment and add to a sense of community. Detached single family residential dwelling units are permitted uses within the R-8 zoning designation. Density: The area of public and private streets and critical areas would be deducted from the gross site area to determine the “net” site area prior to calculating density. In order to calculate the proposed density of the project, any area of public road, private driveway/easement, and/or Shum Short Plat, PRE21-000359 Page 2 of 5 October 21, 2021 CityofRenton\Department Folders\Community and Economic Development (CED)\Current Planning\Pre- Applications\2021\PRE21-000359\Working Files critical area dedication must be known. All fractions which result from net density calculations shall be truncated at two (2) numbers past the decimal (e.g., 4.5678 becomes 4.56). Calculations for minimum or maximum density that result in a fraction that is 0.50 or greater shall be rounded up to the nearest whole number. Those density calculations resulting in a fraction that is less than 0.50 shall be rounded down to the nearest whole number. Based on the gross land area of 17,174 square feet, the 2-lot proposal arrives at a gross density of approximately 5.07 du/ac (2 lots / 0.39 gross acres = 5.07 du/ac). Based on the gross density of 5.07 du/ac, the subject site would meet the minimum density requirements of the zone. The applicant would be required to demonstrate compliance with the net density requirements of the zone at the time of formal application, after deduction of ROW dedication. Development Standards: The project would be subject to RMC 4-2-110A, “Development Standards for Single Family Zoning Designations” effective at the time of complete application (noted as “R-8 standards” herein). Minimum Lot Size, Width and Depth – The minimum lot size permitted in the R-8 zone is 5,000 square feet for parcels being subdivided. Minimum lot width is 50 feet for interior lots and 60 feet for corner lots; minimum lot depth is 80 feet. Please note that for short plats of parcels smaller than one acre, one parcel may be allowed to be smaller than the required minimum lot size, if all other parcels meet the required minimum lot size standard of the zone. In the R-8 zone, one parcel may be allowed to be four thousand five hundred (4,500) square feet. Based on the pre-application submittal provided by the applicant, proposed lots 1 and 2 appear to comply with minimum lot size, width, and depth requirements of the zone. The applicant will need to demonstrate compliance with the minimum lot size, width, and depth requirements of the zone (following deduction of required ROW dedication), based on the definitions of lot size, width, and depth (RMC 4-11-120), at the time of formal land use application. Building Standards – The R-8 standards allow a maximum building coverage of 50% of the lot area. The maximum impervious coverage in the R-8 zone is 65%. The maximum wall plate height is restricted to 24 feet, and the buildings shall be not more than two stories. Roofs with a pitch equal to or greater than 4:12 may project an additional six (6) vertical feet from the maximum wall plate height; common rooftop features, such as chimneys, may project an additional four (4) vertical feet from the roof surface. Non-exempt vertical projections (e.g., decks, railings, etc.) shall not extend above the maximum wall plate height unless the projection is stepped back one-and-a-half (1.5) horizontal feet from each façade for each one (1) vertical foot above the maximum wall plate height. The maximum wall plate height for detached accessory structures is 12 feet. The gross floor area must be less than that of the primary structure. Accessory structures are also included in building lot coverage calculations. The new single-family homes would need to comply with the maximum building coverage, impervious surface requirements, and building height regulations of the zone at the time of building permit review. Setbacks – Setbacks are the minimum required distance between the building footprint and the property line. The required setbacks for the R-8 zone are: Front yard: 20 feet for the primary structure; Rear yard: 20 feet; Side yards: 5 feet; and secondary front yards: 15 feet. Side yard along a street is defined as the yard requirement that is neither a front yard nor a rear yard, yet it abuts a street right-of-way or private street. New single-family homes must comply with the secondary front yard setback requirements from Queen Ave NE. Compliance with required Shum Short Plat, PRE21-000359 Page 3 of 5 October 21, 2021 CityofRenton\Department Folders\Community and Economic Development (CED)\Current Planning\Pre- Applications\2021\PRE21-000359\Working Files setbacks for the new single-family homes would be verified at the time of building permit application. Access/Parking: Access to the site appears to be proposed via residential driveways off of either Pierce Ave NE or Queen Ave NE. Each lot is required to accommodate off street parking for a minimum of two vehicles. The maximum width of single loaded garage driveways shall not exceed 9 feet and double loaded garage driveways shall not exceed 16 feet. Based on restrictions identified on the underlying recorded plat maps (King County recording numbers 8004230583 and 9802099012), access to the lots via Queen Ave NE is prohibited. Compliance with driveway and parking standards would be verified at the time of building permit review. Landscaping: With the exception of critical areas, all portions of the development area not covered by structures, required parking, access, circulation or service areas, must be landscaped with native, drought-resistant vegetative cover. The minimum on-site landscape width required along street frontages is 10 feet and shall contain trees, shrubs, and landscaping. Street trees in the ROW planter will also be required. Landscaping may include hardscape such as decorative paving, rock outcroppings, fountains, plant containers, etc. Minimum planting strip widths between the curb and sidewalk are established according to the street development standards of RMC 4-6-060. Street trees and, at a minimum, groundcover are to be located in this area when present. Street trees shall be planted in the center of the planting strip between the curb and the sidewalk at the following intervals; provided, that, where right-of-way is constrained, irregular intervals and slight increases or decreases may be permitted or required. Additionally, trees shall be planted in locations that meet required spacing distances from facilities located in the right-of-way including, but not limited to, underground utilities, street lights, utility poles, traffic signs, fire hydrants, and driveways; such spacing standards are identified in the City’s Approved Tree List. Generally, the following spacing is required: i. Small-sized maturing trees: thirty feet (30') on center; ii. Medium-sized maturing trees: forty feet (40') on center; and iii. Large-sized maturing trees: fifty feet (50') on center. A conceptual landscape plan shall be provided with the building permit application as prepared by a registered Landscape Architect, a certified nurseryman or other certified professional. Storm drainage facilities are required to comply with the minimum 15-foot perimeter landscaping strip on the outside of the fence unless otherwise determined through the site plan review or subdivision review process. Please refer to landscape regulations RMC 4-4-070 for further general and specific landscape requirements. Significant Tree Retention: An aerial image of the site identifies mature trees on the site. If significant trees (greater than 6-inch caliper or 8-caliper inches for alders and cottonwoods) are proposed to be removed, a tree inventory and a tree retention plan along with an arborist report, tree retention plan and tree retention worksheet shall be provided with the formal land use application as defined in RMC 4-8-120. The tree retention plan must show preservation of at least 30% of significant trees. The Administrator may authorize the planting of replacement trees on the site if it can be demonstrated to the Administrator's satisfaction that an insufficient number of trees can be retained. Please refer to Tree Retention and Land Clearing Regulations RMC 4-4-130 for further general and specific tree retention and land clearing requirements. In addition to retaining 30% of existing significant trees, each new lot would be required to provide a minimum tree density of 2 trees per 5,000 square feet of lot area onsite. Protected trees that do not contribute to a lot's required minimum tree density shall be held in perpetuity within a tree protection tract. Shum Short Plat, PRE21-000359 Page 4 of 5 October 21, 2021 CityofRenton\Department Folders\Community and Economic Development (CED)\Current Planning\Pre- Applications\2021\PRE21-000359\Working Files Significant trees shall be retained in the following priority order: Priority One: Landmark trees; significant trees that form a continuous canopy; significant trees on slopes greater than twenty percent (20%); Significant trees adjacent to critical areas and their associated buffers; and Significant trees over sixty feet (60') in height or greater than eighteen inches (18") caliper. Priority Two: Healthy tree groupings whose associated undergrowth can be preserved; Other significant native evergreen or deciduous trees; and Other significant non- native trees. Priority Three: Alders and cottonwoods shall be retained when all other trees have been evaluated for retention and are not able to be retained, unless the alders and/ or cottonwoods are used as part of an approved enhancement project within a critical area or its buffer. The Administrator may require independent review of any land use application that involves tree removal and land clearing at the City's discretion. If staff determines that the trees cannot be retained, replacement trees, with at least a 2-inch caliper or an evergreen at least 6 feet tall, shall be planted at a rate of 12 caliper inches of new trees to replace each protected tree removed. A formal tree retention plan prepared by an arborist or landscape architect would be reviewed at the time of the Short Plat application. Fences/Walls: If the applicant intends to install any fences or retaining walls as part of this project, the location must be designated on the landscape plan or grading plan. A fence and/or wall detail should also be included on the plan. A fence taller than 6 feet shall require a building permit or an explicit exemption from the Building Official. A retaining wall that is 4 feet or taller, as measured by the vertical distance from the bottom of the footing to the finish grade at the top of the wall requires a building permit. A fence shall not be constructed on top of a retaining wall unless the total combined height of the retaining wall and the fence does not exceed the allowed height of a standalone fence. For more information about fences and retaining walls refer to RMC 4-4-040. Critical Areas: According to COR Maps, no critical areas are located on the project site. However, it is the applicant’s responsibility to ascertain whether any critical areas are present on the site. Environmental Review: Projects consisting of nine (9) units or less and that will not impact a critical area are exempt from Environmental (SEPA) Review. Based on the proposal submitted by the applicant, the proposed project would be exempt from SEPA review. Permit Requirements: The proposal would require administrative short plat approval. The application would be reviewed within an estimated time frame of six to eight weeks. The 2021 administrative short plat application fee is $5,410.00. Each modification request is $260.00. A 5% technology fee would also be assessed at the time of land use application. All fees are subject to change. Detailed information regarding the land use permit application submittal requirements can be found on the Short Plat Submittal Requirements checklist. Other informational applications and handouts can be found on the City’s Digital Records Library. The City requires electronic plan submittal for all applications. Please refer to the City’s Electronic File Standards. A Final Plat application, and it’s associated fee, will be required following construction of the plat’s infrastructure. Public Information Sign: Public Information Signs are required for all Type II and Type III Land Use Permits as classified by RMC 4-8-080. Public Information Signs are intended to inform the Shum Short Plat, PRE21-000359 Page 5 of 5 October 21, 2021 CityofRenton\Department Folders\Community and Economic Development (CED)\Current Planning\Pre- Applications\2021\PRE21-000359\Working Files public of potential land development, specific permits/actions being considered by the City, and to facilitate timely and effective public participation in the review process. The applicant must follow the specifications provided in the public information sign handout. The applicant is solely responsible for the construction, installation, maintenance, removal, and any costs associated with the sign. Fees: In addition to the applicable building and construction fees, impact fees would be required. The fee in effect at the time of permit issuance will apply. The 2021 impact fees are as follows: A Transportation Impact Fee based on $10,861.69 per each new detached dwelling unit. A Parks Impact Fee based on $2,914.99 per each new detached dwelling unit. A Fire Impact fee of $829.77 per each new detached dwelling unit. Renton School District Impact Fee is $7,681.00 per each new detached dwelling unit. A handout listing Renton’s development-related fees is available on the City of Renton website for your review. Next Steps: When the formal application materials are complete, should a land use application be needed, the applicant shall have the application materials pre-screened prior to submitting the complete application package. Please contact Angelea Weihs, Associate Planner at aweihs@rentonwa.gov or 425-430-7312 for an appointment. Expiration: Upon approval, the Short Plat is valid for five years with a possible one year extension (RMC 4-7-070M). It is the responsibility of the owner to monitor the expiration date.