HomeMy WebLinkAbout320.21-1/2" AND 2" WATER SERVICE DETAIL
CAUTION: VALVE BOX SHOULD NOT REST ON
PIPE. LATER COMPACTION IN AREA OF VALVE BOX
COULD CAUSE THE BREAKAGE OF THE SERVICE.
CITY
PIPING
w
C
Z
z
J
J
}
IN UNIMPROVED
>
RIGHT—OF—WAY INSTALL METER
a
BOX AT PROPERTY LINE WITH
ii
0
12" LONG COPPER TAILPIECE
0
X
o_
Of
o_
COUPLING x MIPT CAST IRON OR DUCTILE IRON WATERMAIN
9" MIN.
12" MAX.
z� za
Q
g ?
W 3 �� M:2>
0 4 o, LEAVE EXPOSED : 0 0
N r) 12„
BY PASS NOT ALLOWED
�o FOR IRRIGATION METERS
MATERIAL LIST FOR 2" SERVICE: METER LOCATED IN PLANTING STRIP
BETWEEN CURB & SIDEWALK
1. 2" tapped tee, on new water main.
2. 4" long X 2" brass nipple with threaded ends (MIPT).
3. 2" resilient seat gate valve with threaded ends, square operating nut,
and valve nut extension if required (see standard detail 330.1).
4. Two piece cast iron valve box. Standard 8" top section with regular
base section, length to fit, "lug" type cover. 2" brass bushing (MIPT x
FIPT).
5. 2 each 2" brass or bronze nipples 6" length, threaded ends. 2 each
2"-90° brass or bronze elbows (FIPT x FIPT).
6. 2" (MIPT) x compression fitting, Ford C84-66 or equal.
7. 2" soft copper tubing type K or brass nipples (MIPT x MIPT), length to
fit.
8. 2" threaded brass 90' ell.
9. 2" Customsetter with by—pass Ford: VBH 86-12B-11-77 (x 17-3/16"
), McDonald Brass: 30B715WDFF775 or Mueller B-1427-2", with flanged
angle ball valve and padlock wings on inlet, and angle check valve
outlet, ball valve on bypass with padlock wings. Customsetter shall
have vertical inlet and outlet.
10. Rigid meter spreader to be supplied and installed in meter setter by
contractor.
11. Water meter shall be supplied and installed by City of Renton upon
payment of all related water meter fee and satisfactory pressure and
purity tests.
12. 17"x30" Plastic meter box equal to Mid—States Plastics, Inc. BCF Series
MSBCF 1730-18 with 2" thick Ductile iron diamond plate cover 18"x31"
equal to Mid—States Plastics, Inc. MSCBC-1730—R with 2" drilled hole
for touchread pit lid, and meter read lid.
13. 2" coupling (compression x FIPT) with 2" plug (MIPT), Ford C-14-66
or equal. The property owner is responsible for any necessary adaptation or
extension of water service.
NOTE:
ALL METER BOXES INSTALLED IN CONCRETE OR PAVED
DRIVEWAYS SHALL BE CAST—IRON EQUAL TO OLYMPIC
FOUNDARY.
EXPANSION JOINTS MUST BE INSTALLED 12" MINIMUM ON BOTH
SIDES OF METER BOX.
PRIVATE
PIPING
MATERIAL LIST FOR 1-1/2" SERVICE: METER LOCATED IN PLANTING STRIP
BETWEEN CURB & SIDEWALK
1. 2" tapped tee on new water main.
2. 4" long X 2" brass nipple with threaded ends (MIPT).
3. 2" resilient seat gate valve with threaded ends, square operating nut, and
valve nut extension if required (see standard detail 330.1).
4. Two piece cast iron valve box. Standard 8" top section with regular base
section, length to fit, "lug" type cover.
5. 2" X 1-1/2" hex brass bushing (MIPT x FIPT. 2 each 1-1/2" brass or
bronze nipples 6" length, threaded ends. 2 each 1-1/2"-90° brass or
bronze elbows (FIPT x FIPT.
6. 1-1/2" (MIPT) x compression fitting, Ford C84-66 or equal.
7. 1-1/2" soft copper tubing type K or brass nipples (MIPT x MIPT), length
to fit.
8. 1-1/2" threaded brass 90° ell, for Ford L44-77 or equal.
9. 1-1/2" Customsetter with by—pass Ford: VBH 86-12B-11-66 (x
13-3/16"), McDonald Brass: 3OB612WDFF665 or Mueller B-1427-1 1/2",
with flanged angle ball valve and padlock wings on inlet, and angle check
valve outlet, ball valve on bypass with padlock wings. Customsetter shall
have vertical inlet and outlet.
10. Rigid meter spreader to be supplied and installed in meter setter by
contractor.
11. Water meter shall be supplied and installed by City of Renton upon
payment of all related water meter fee and satisfactory pressure and
purity tests.
12. 17"x30" Plastic meter box equal to Mid—States Plastics, Inc. BCF Series
MSBCF 1730-18 with 2" thick Ductile iron diamond plate cover 18"x31"
equal to Mid—States Plastics, Inc. MSCBC-1730—R with 2" drilled hole for
touchread pit lid.
13. 1-1/2" coupling (compression x FIPT) with 1-1/2" plug (MIPT), Ford
C-14-66 or equal. The property owner is responsible for any necessary
adaptation or extension of water service.
+
ZY e� �+ PUBLIC WORKS 1 %2" AND 2" WATER SERVICE LOCATED STD. PLAN — 320.2
�O DEPARTMENT IN PLANTING STRIP
N,yp MARCH 2010
CRUSHED ROCK
�J BASE TO SUPPORT
AVAULT.
A
—
DRILL 2" DIA. HOLE FOR
TOUCHREAD DEVICE
QUICK—JOINT
COUPLING x MIPT CAST IRON OR DUCTILE IRON WATERMAIN
2-1/2" MIN. FROM NEAREST
NOTE:
AND FRONT EDGE OF PIT LID
THE CENTER OF THE HOLE MUST BE AT LEAST 1" FROM
UNDERNEATH RIBS UNLESS THE RIB SPACING ALLOWS
THE NUT TO TIGHTEN AGAINST THE OPEN SIDE OF
MORE THAN ONE RIB.
TYPICAL RIB
MATERIAL LIST FOR 2" SERVICE: METER LOCATED IN PLANTING STRIP
BETWEEN CURB & SIDEWALK
1. 2" tapped tee, on new water main.
2. 4" long X 2" brass nipple with threaded ends (MIPT).
3. 2" resilient seat gate valve with threaded ends, square operating nut,
and valve nut extension if required (see standard detail 330.1).
4. Two piece cast iron valve box. Standard 8" top section with regular
base section, length to fit, "lug" type cover. 2" brass bushing (MIPT x
FIPT).
5. 2 each 2" brass or bronze nipples 6" length, threaded ends. 2 each
2"-90° brass or bronze elbows (FIPT x FIPT).
6. 2" (MIPT) x compression fitting, Ford C84-66 or equal.
7. 2" soft copper tubing type K or brass nipples (MIPT x MIPT), length to
fit.
8. 2" threaded brass 90' ell.
9. 2" Customsetter with by—pass Ford: VBH 86-12B-11-77 (x 17-3/16"
), McDonald Brass: 30B715WDFF775 or Mueller B-1427-2", with flanged
angle ball valve and padlock wings on inlet, and angle check valve
outlet, ball valve on bypass with padlock wings. Customsetter shall
have vertical inlet and outlet.
10. Rigid meter spreader to be supplied and installed in meter setter by
contractor.
11. Water meter shall be supplied and installed by City of Renton upon
payment of all related water meter fee and satisfactory pressure and
purity tests.
12. 17"x30" Plastic meter box equal to Mid—States Plastics, Inc. BCF Series
MSBCF 1730-18 with 2" thick Ductile iron diamond plate cover 18"x31"
equal to Mid—States Plastics, Inc. MSCBC-1730—R with 2" drilled hole
for touchread pit lid, and meter read lid.
13. 2" coupling (compression x FIPT) with 2" plug (MIPT), Ford C-14-66
or equal. The property owner is responsible for any necessary adaptation or
extension of water service.
NOTE:
ALL METER BOXES INSTALLED IN CONCRETE OR PAVED
DRIVEWAYS SHALL BE CAST—IRON EQUAL TO OLYMPIC
FOUNDARY.
EXPANSION JOINTS MUST BE INSTALLED 12" MINIMUM ON BOTH
SIDES OF METER BOX.
PRIVATE
PIPING
MATERIAL LIST FOR 1-1/2" SERVICE: METER LOCATED IN PLANTING STRIP
BETWEEN CURB & SIDEWALK
1. 2" tapped tee on new water main.
2. 4" long X 2" brass nipple with threaded ends (MIPT).
3. 2" resilient seat gate valve with threaded ends, square operating nut, and
valve nut extension if required (see standard detail 330.1).
4. Two piece cast iron valve box. Standard 8" top section with regular base
section, length to fit, "lug" type cover.
5. 2" X 1-1/2" hex brass bushing (MIPT x FIPT. 2 each 1-1/2" brass or
bronze nipples 6" length, threaded ends. 2 each 1-1/2"-90° brass or
bronze elbows (FIPT x FIPT.
6. 1-1/2" (MIPT) x compression fitting, Ford C84-66 or equal.
7. 1-1/2" soft copper tubing type K or brass nipples (MIPT x MIPT), length
to fit.
8. 1-1/2" threaded brass 90° ell, for Ford L44-77 or equal.
9. 1-1/2" Customsetter with by—pass Ford: VBH 86-12B-11-66 (x
13-3/16"), McDonald Brass: 3OB612WDFF665 or Mueller B-1427-1 1/2",
with flanged angle ball valve and padlock wings on inlet, and angle check
valve outlet, ball valve on bypass with padlock wings. Customsetter shall
have vertical inlet and outlet.
10. Rigid meter spreader to be supplied and installed in meter setter by
contractor.
11. Water meter shall be supplied and installed by City of Renton upon
payment of all related water meter fee and satisfactory pressure and
purity tests.
12. 17"x30" Plastic meter box equal to Mid—States Plastics, Inc. BCF Series
MSBCF 1730-18 with 2" thick Ductile iron diamond plate cover 18"x31"
equal to Mid—States Plastics, Inc. MSCBC-1730—R with 2" drilled hole for
touchread pit lid.
13. 1-1/2" coupling (compression x FIPT) with 1-1/2" plug (MIPT), Ford
C-14-66 or equal. The property owner is responsible for any necessary
adaptation or extension of water service.
+
ZY e� �+ PUBLIC WORKS 1 %2" AND 2" WATER SERVICE LOCATED STD. PLAN — 320.2
�O DEPARTMENT IN PLANTING STRIP
N,yp MARCH 2010